Technical description and composition of the FUSION FLTV-24W9D TV, panel type and applicable modules. The composition of the modules.FUSION LED
Model: FLTV-24W9D
Chassis / Version: CV7168L-A
Panel: TC236F101
MainBoard: CV7168L-A
IC MainBoard: SPI Flash: 25Q32;
Tuner: F21WT-3BAR-E
Technical Specifications FLTV-24W9D
FUSION FLTV-24W9D
General repair guidelines for TV LCD LED
Repair of the FUSION FLTV-24W9D TV should begin with a careful external examination of all its components and modules. Sometimes, based on visible changes in the components of the device, it is possible to draw some conclusions and decide on the direction of further troubleshooting even before the necessary measurements are taken. Elements with visible damage, for example, capacitors swelled up after boiling the electrolyte, charred resistors in certain nodes of the circuit, as well as ring cracks in solders will help the master to guess the causes and possible consequences of the malfunction.
If the TV does not turn on, no indicators on its front panel are lit or blinking. Also, if the TV does not respond to the remote control and buttons, does not make any sounds or any signs of operability when turned on, there is a certain probability that the power module is defective and needs repair. Sometimes with similar manifestations, a problem can only occur in the absence of standby power. In the general case, first of all, it is necessary to check the electrolytic capacitors of the secondary rectifier filters and the fuse at the input of the network. If it is cut off, then it is necessary to check the diodes of the rectifier bridge and the key transistor of the converter for a breakdown of the PN junctions, which can either be on a separate radiator or integrated with a PWM controller in a common chip. Possible options.
Mos-Fet keys used in switching power supplies (SMPS) rarely fail for no reason to look for when checking other circuit elements. Often the breakdown is caused by malfunctions of electrolytic capacitors or semiconductor elements in the primary circuit, or by a break in the resistors in the stabilization circuits. The PWM controller chip may also cause a breakdown of the power switch of the converter.
If, when you turn on the TV, the image appears and immediately disappears, or is absent initially when you turn on, but the sound is there and other functions work, there is a high probability of a malfunction of the LED driver (power converter for the backlight LEDs of the TC236F101 panel).
Often there is a need for disassembling the panel to check the health of the LEDs, as well as contact connections in the connectors and soldering.
When diagnosing, it is necessary to take into account that it is impossible to check the open in the circuit of the LED lines without disassembling the panels using a tester or a multimeter. To open all PN junctions connected in series, a voltage of the order of several tens of volts is required, and ideally, a current source.
If the CV7168L-A motherboard is faulty, first of all it is necessary to check all the linear stabilizers and power converters of its chips, and also, if necessary, update the software (software). Sometimes you can check the health of MB only by replacement.
In some cases, chip repair may be required to repair the MB (SSB) board - SPI Flash: 25Q32; to new or obviously serviceable. In cases where BGA technologies are used, defects are usually localized by the heating method.If you suspect a malfunction of the F21WT-3BAR-E tuner, first of all, it is necessary to verify the correctness of the software, as well as the presence of the necessary voltage levels at the corresponding terminals of the tuner.
Owners of the FLTV-24W9D TV are recommended to repair only qualified specialists with experience! Self-repair attempts without the appropriate knowledge and skills can lead to serious negative consequences!
FIRMWARE FOR SPI FLASH -----------> FUSION FLTV-24W9D, Main: CV7168L-A, Panel: TC236F101
The appearance of the MainBoard CV7168L-A is shown in the figure below:CV7168L-A
Main features of the FUSION FLTV-24W9D device:
The matrix (LED panel) TC236F101 is installed.
The required supply voltage for all nodes of the TV FUSION FLTV-24W9D provides a switching power supply.
MainBoard - the main board (motherboard) is a CV7168L-A module, using SPI Flash chips: 25Q32; and others.
The F21WT-3BAR-E tuner provides television reception and channel tuning.
FUSION FLTV-24W9D TV with LCD display TC236F101, diagonal size 24 "(61 cm) 16: 9 format. The required brightness of the screen 300 cd / m² is provided by LED backlight LED. Contrast, as the ratio of maximum brightness to minimum, is 1000: 1. Dynamic contrast ratio of 20,000: 1 is achieved by special control of the LEDs. The LED-panel of this TV is equipped with an end LED backlight - Edge LED. The design and technical capabilities of the TV include viewing programs and movies in high quality HD at a resolution of 1920x1080 pixels in graphic format standard 1080p (Full HD). The input high-frequency or video signal can be processed in analog systems PAL, SECAM, NTSC. Graphic processing and digital signal generation occurs in standards 480i, 480p, 576i, 576p, 720p, 1080i, 1080p. Supported media file formats : MP3, WMA, MPEG4, DivX, VideoCD, SVCD, JPEG.
The power of the acoustic system of sound 6 W (2x3 W) provide two speakers. The audio processing system NICAM STEREO is used.
The external interface (communication with other devices) is supported by standard input and output connectors: antenna input (RF), AV, audio x2, component, SCART, VGA, HDMI, USB. An output for connecting headphones is provided. To connect a computer or laptop to this TV model, a VGA (D-Sub 15) connector is used on the TV case, this interface supports resolutions: 640x480, 800x600, 1024x768, 1280x1024, 1360x768.
The power consumed by the TV working in the network mode is 40 watts.
Overall dimensions: 583x460x165 mm.
TV Weight: 5.5 kg.
Attention! The TC236F101 panel of the FUSION FLTV-24W9D LED TV is an expensive and unreliable element.
Avoid any impact on the glass and pressure on the surface of the screen to avoid damage to the LED panel!
It is also unsafe to get liquid on the screen. Sometimes one drop is enough if it flows down the glass onto the cables so that the TV becomes unrepairable.
