Technical description and composition of the FUSION FLTV-32K62 TV, panel type and applicable modules. The composition of the modules.FUSION LED
Model: FLTV-32K62
Chassis / Version: TP.VST59.P8B
Panel: LC320DXJ (SF) (E1)
T-CON: 6870C-0442B
LED driver (backlight): integrated into Mainboard
PWM LED driver: LD5850GS
MOSFET LED driver: ME15N10
Power Supply (PSU): integrated into Mainboard
PWM Power: PWM SOT23-6
MOSFET Power: 7N65L
MainBoard: TP.VST59.P8B
IC MainBoard: CPU: TSUMV59XE-Z1, SPI Flash: 25Q32, TPA3110LD2
Technical Specifications FLTV-32K62
FUSION FLTV-32K62
General repair guidelines for TV LCD LED
Repair of the FUSION FLTV-32K62 TV should begin with a careful external examination of all its components and modules. According to some external signs of a change in the state of some elements, it is sometimes possible to make assumptions about the nature of the defect, as well as determine the further direction of the troubleshooting. Experienced repairmen are well aware of what ring cracks in solder pins look like, swollen capacitors, and other causes of problems in electronic devices.
Sometimes the FUSION FLTV-32K62 TV simply does not turn on. No control lights on the front panel are lit or blinking, the TV does not respond to the remote control and does not make any sounds or any signs of life when turned on. The most likely cause of the malfunction is a failure of the common power module. If it is working properly, you must check the standby batteries on the Main Board. When diagnosing and repairing the power supply, first of all, replace the swollen capacitors of the filter of the secondary rectifiers and check the fuse and, if it is broken, it is necessary to identify the cause. Often in such cases, an avalanche (thermal) breakdown is detected in the power semiconductor elements of the module — rectifier diodes and transistors in the primary circuit.
It should be remembered that in the practice of repair, usually the power switches in switching power supplies (SMPS) do not fail due to their poor quality and, in such cases, it is necessary to look for the cause that led to a malfunction and provoked a breakdown of the key. Most often, the culprits of the accident are dried electrolytic capacitors or dangling resistors in the primary circuit, or the PWM controller chip itself may be faulty. It is also necessary to check all the semiconductor elements of the stabilization circuit in the primary and secondary circuits.
If the FUSION FLTV-32K62 does not have an image, but there is sound, the backlight LEDs of the LC320DXJ (SF) (E1) panel or their power converter may malfunction.
In case of breaks in the LED circuit, a complete disassembly of the panel is required, the LEDs are checked for an open circuit, as well as the reliability of the connections in the connectors and rations of the terminals.
To check the LED lines for breaks without disassembling the panel, for example, a current source will help. It is impossible to open series-connected PN junctions with a simple multimeter, a voltage of the order of several tens of volts is required.
Diagnostics and repair of the TP.VST59.P8B motherboard usually begins with a test of the performance of the stabilizers and power converters of the module chips. In some cases, a software update is required.
If it is not possible to replace the MB (SSB) card, you must check the health of its elements - CPU: TSUMV59XE-Z1; SPI Flash: 25Q32; . Defective components should be replaced.
It should be remembered! Attempts to repair the FUSION FLTV-32K62 TV, in the absence of the necessary qualifications and experience, are categorically not recommended and are fraught with negative consequences, up to the complete non-repairability of the device!
One of the typical FUSION FLTV-32K62 malfunctions often occurs in the LG panel LC320DXJ (SF) (E1).
External manifestations: there is no image, the backlight does not work. In most such cases, the LEDs turn out to be malfunctioning, which during testing turn out to be either in a cliff or with broken internal zener diodes.
LEDs must be replaced, and the maximum current from the driver should be limited to 10-20%.
FIRMWARE FOR SPI FLASH ------> FUSION FLTV-32K62, Main: TP.VST59.P8B, Panel: LC320DXJ(SF)(E1)
The appearance of MainBoard TP.VST59.P8B is shown in the figure below:TP.VST59.P8B
TP.VST59.P8B can be used in TVs:
FUSION FLTV-32K62 (Panel LC320DXJ (SF)(E1)), FUSION FLTV-28K62 (Panel ST2751A01-4), THOMSON T32ED07U-01B (Panel LC320DXE (SF)(R1) ).
Main features of the FUSION FLTV-32K62 device:
Installed matrix (LED-panel) LC320DXJ (SF) (E1).
The matrix control uses the Timing Controller (T-CON) 6870C-0442B.
An integrated LED driver is used to power the backlight LEDs, it is controlled by the LD5850GS PWM controller. As the power elements of the LED driver, keys of the type ME15N10 are used.
The power module is combined with the MainBoard and is designed according to a flyback AC / DC voltage converter using PWM SOT23-6 microcircuits and power switches of the 7N65L type.
MainBoard - the main board (motherboard) is a TP.VST59.P8B module, using CPU chips: TSUMV59XE-Z1, SPI Flash: 25Q32, TPA3110LD2 and others.
Additional technical information about the panel:
Brand: LG Display
Model: LC320DXJ-SFE1
Type: a-Si TFT-LCD, CELL
Diagonal size: 31.5 inch
Resolution: 1366x768, WXGA
Display Mode: IPS, Normally Black, Transmissive
Active Area: 697.685x392.256 mm
Surface: Antiglare (Haze 1%), Hard coating (3H)
Glass Depth: 0.50 + 0.50 mm
Contrast Ratio: 1200: 1
Display Colors: 16.7M (6-bit + Dithering)
Response Time: 8/10 (Tr / Td)
Frequency: 60Hz
Signal Interface: LVDS (1 ch, 8-bit), 30 pins
Voltage: 12.0V
FUSION FLTV-32K62 TV with LC320DXJ LCD display, 32 "(81 cm) diagonal size in 16: 9 format. The required brightness of the screen is 280 cd / m² LED backlighting. Dynamic contrast ratio of 100000: 1 is achieved by special control of the LEDs. In The LED panels of this TV are equipped with edge LED backlighting - Edge LED. You can view images in high quality HD at a resolution of 1366x768 pixels in the standard for graphic decomposition 720p (HD Ready). The input high-frequency or video signal can be processed in analog systems PAL, SECAM, NTSC Graphic processing and digital signal generation occurs in the standards 480i, 480p, 576i, 576p, 720p, 1080i. Supported media file formats: MP3, WMA, MPEG4, MKV, JPEG.
The power of the sound system 10 W (2x5 W) provides two speakers. The audio processing system NICAM STEREO is used.
The external interface (communication with other devices) is supported by standard input and output connectors: antenna input (RF), SCART, HDMI, USB. An output for connecting headphones is provided. To connect a computer or laptop to this TV model, a VGA (D-Sub 15) connector is used on the TV case, this interface supports resolutions: 640x480, 800x600, 1024x768, 1360x768.
Attention! The LC320DXJ (SF) (E1) panel of the FUSION FLTV-32K62 LED TV is an expensive and unreliable element.
Avoid any impact on the glass and pressure on the surface of the screen to avoid damage to the LED panel!
It is also unsafe to get liquid on the screen. Sometimes one drop is enough if it flows down the glass onto the cables so that the TV becomes unrepairable.
