Technical description and composition of the TV SUPRA STV-LC2210W, type of panel and applicable modules. The composition of the modules.SUPRA
Model: STV-LC2210W
Chassis / Version: JUG7.820.638-7 LS07
Panel: LTA216AT01
MainBoard: JUG7.820.638-7 LS07
IC MainBoard: CPU TSUMV26KE - LF, Flash 24C32 (U14) M25P40 (U15)
Tuner: CH TAF6 - C2121VH 1509BP
Technical Specifications STV-LC2210W
SUPRA STV-LC2210W
General repair guidelines for TV LCD
It is recommended that you start diagnostics and repair of SUPRA with the JUG7.820.638-7 LS07 chassis, as well as other electronic devices, with an external inspection of the external and internal elements. Often, according to the external signs and nature of the damage to the elements, it becomes possible to draw some conclusions and determine a further algorithm for finding a defect before making the necessary measurements at control points. If charred resistors, swollen electrolytic or cermet capacitors, ring cracks in the soldered terminals of transformers or heating elements are detected, it is advisable to establish the causes and consequences of the malfunction that has arisen, as well as to check the connected elements and assemblies.
In the absence of any signs of operability, when the SUPRA STV-LC2210W does not turn on and does not signal anything with the control lights on the panel, there is a possibility of a malfunction of the TV power module. With the same manifestations, the power regulator of the control processor on the motherboard may be faulty. When diagnosing and repairing the power supply, after replacing the swollen capacitors of the filters of the secondary rectifiers (if any), you must first check the mains fuse. When it is broken, the power elements of the transistors and diodes of the rectifier bridge should be checked for avalanche (thermal) breakdown.
It should be remembered that in the practice of repair, usually the power switches in switching power supplies (SMPS) do not fail due to their poor quality and, in such cases, it is necessary to look for the cause that led to a malfunction and provoked a breakdown of the key. Most often, the culprits of the accident are dried electrolytic capacitors or dangling resistors in the primary circuit, or the PWM controller chip itself may be faulty. It is also necessary to check all the semiconductor elements of the stabilization circuit in the primary and secondary circuits.
If the SUPRA STV-LC2210W does not have an image, but there is sound and the TV is controlled from the remote control, a malfunction in the display backlight nodes is likely. The lamps or the power converter - inverter may be faulty. Often in such cases, when you turn on the TV, an image appears and immediately disappears. First of all, it is necessary to verify the operability of the electrolytic capacitors of the rectifier filter supplying the inverter, and check the LCD lamps by connecting external and obviously serviceable for diagnosis to the connectors. Turning off the protection for diagnostic purposes, it must be remembered that in this case there is a risk of failure of the power elements of the inverter. Upon completion of the diagnosis, all regular protection circuits should be restored.
When trying to repair the motherboard, you should first check the serviceability of linear stabilizers or power converters of microcircuits and, if necessary, update the software (software). In some cases, to repair the MB (SSB) board, it may be necessary to replace the chips - CPU TSUMV26KE - LF, Flash 24C32 (U14) M25P40 (U15) with new or obviously working ones. In cases where BGA technologies are used, defects are usually localized by the heating method.
Attention! Users and owners of STV-LC2210W TVs who do not have the appropriate qualifications, knowledge and experience are strongly discouraged from attempting self-repair in order to avoid negative consequences that could lead to complete non-serviceability of the device.
Main features of the SUPRA STV-LC2210W device:
FIRMWARE FOR SPI FLASH -----------> EEPROM SUPRA STV-LC2210W, Main: JUG7.820.638-7 LS07, Panel: LTA216AT01
Installed matrix (LCD-panel) LTA216AT01.
The required supply voltage for all nodes of the TV SUPRA STV-LC2210W provides a switching power supply.
MainBoard - the main board (motherboard) is a JUG7.820.638-7 module, using CPU chips TSUMV26KE - LF, Flash 24C32 (U14) M25P40 (U15) and others.
Tuner CH TAF6 - C2121VH 1509BP provides reception of television programs and tuning to channels.
Information from an alternative source:
SUPRA STV-LC2210W Version V2K07
Panel Type (Matrix): LTA216AT02
Motherboard: JUG7.820.638-3, TSUMV26KE-LF, 25Q40T, 24LC32B, Tuner: CH TAF6-C2I21VH 1509BP
T-con: 216AT01S2LV0.3, LRX4211X0A, 416WP, A616BG, I7814HS x2
PSU & Invertor: IP0220430 REV:00, LD7575BGS, SVD7N60F, TL494C, ME4542 х2, Tr-r: IVTEL1900033 1046 x2
Additional technical information about the panel:
Brand: SAMSUNG
Model: LTA216AT01
Type: a-Si TFT-LCD, Panel
Diagonal size: 21.6 inch
Resolution: 1366x768, WXGA
Display Mode: TN, Normally White, Transmissive
Active Area: 477.417x268.416 mm
Surface: Hard coating (3H)
Brightness: 350 cd / m²
Contrast Ratio: 800: 1
Display Colors: 16.7M (6-bit + Hi-FRC), CIE1931 72%
Frequency: 60Hz
Lamp Type: 4 pcs CCFL Without Driver
Signal Interface: LVDS (1 ch, 8-bit), 30 pins
Voltage: 5.0V
SUPRA STV-LC2210W LCD TV with LTA216AT01 LCD, 22 "(55 cm) diagonal display in 16: 9 format. 300 cd / m² screen brightness is provided by CCFL (EEFL) fluorescent lamps. Contrast is the ratio of maximum brightness to minimum is 1000: 1. You can watch broadcasts and movies and images in high quality HD at a resolution of 1366x768 pixels in the standard of graphic decomposition 720p (HD Ready). The input high-frequency or video signal is decoded in analog systems PAL, SECAM, NTSC. Graphic processing and digital signal generation occurs in the standards 480i, 480p, 576i, 576p, 720p, 1080i.
The power of the speaker system of sound 4 W (2x2 W) provide two speakers. The audio processing system NICAM STEREO is used.
The external interface (communication with other devices) is supported by standard input and output connectors: antenna input (RF), AV, audio x3, S-Video, component, VGA, HDMI. An output for connecting headphones is provided. To connect a computer or laptop to this TV model, a VGA (D-Sub 15) connector is used on the TV case, this interface supports resolutions: 640x480, 800x600, 1024x768.
The power consumed by the TV in the operating mode from the network is 65 watts.
Overall dimensions: 600x467x142 mm.
TV Weight: 8 kg.
Attention! The LTRA216AT01 LCD panel of a SUPRA STV-LC2210W LCD TV is its most expensive component.
Avoid hitting the glass and exerting pressure on the screen surface to avoid permanent damage to the LCD panel!
