Technical description and composition of the TV SUPRA STV-LC22811FL, type of panel and applicable modules. The composition of the modules.SUPRA LED
Model: STV-LC22811FL
Chassis / Version: T.VST59.62
Panel: 1080p Full HD, 1920x1080
Power Supply (PSU): Adapter 12V
MainBoard: T.VST59.62
IC MainBoard: CPU TSUMV59XU-Z1, Flash 25Q322, TDA-1517P, TPS54329 (PWM Step-down), BL8024 (PWM Step-down marker GG ..)
Tuner: CDT-3NP5i1-10
Technical Specifications STV-LC22811FL
SUPRA STV-LC22811FL
General repair guidelines for TV LCD LED
It is advisable to start repairing electronic devices, including the SUPRA STV-LC22811FL TV, with an external examination of its external and internal elements. It often happens that visible damage to elements or connections helps determine the direction of the troubleshooting. If charred resistors, swollen electrolytic or cermet capacitors, ring cracks in the soldered terminals of transformers or heating elements are detected, it is advisable to establish the causes and consequences of the malfunction that has arisen, as well as to check the connected elements and assemblies.
Sometimes the SUPRA STV-LC22811FL TV simply does not turn on. No control lights on the front panel are lit or blinking, the TV does not respond to the remote control and does not make any sounds or any signs of life when turned on. The most likely cause of the malfunction is a failure of the common power module. If it is working properly, you need to check the processor batteries on the SSB (Main Board). In the general case, first of all, it is necessary to check the electrolytic capacitors of the secondary rectifier filters and the fuse at the input of the network. If it is broken, then you should check for breakdown of the PN junctions of the rectifier bridge diodes and the key transistor of the converter, which can either be on a separate radiator or integrated with a PWM controller in a common chip. Possible options.
Power switches in switching power supplies (SMPS) fail extremely rarely for no reason and, if they are broken, it is necessary to look for a malfunction in the stabilization circuits by checking electrolytic capacitors, semiconductor devices, and resistors in the primary circuit. The reason may be a malfunction of the PWM controller chip, which can only be checked by replacing it with a new or obviously working one.
In cases where the SUPRA STV-LC22811FL TV has lost its image, and the sound is there and all other functions are operational, there is a possibility of a malfunction of the LED driver (converter for powering the backlight LEDs of the panel 1080p Full HD, 1920x1080). When you turn on the TV, the image may appear briefly and disappear immediately. It must be borne in mind that with such manifestations the LEDs themselves also fail.
A malfunction in the backlight circuits often occurs due to a break in the power supply lines of the LED lines. It requires disassembling the panel and checking the LEDs themselves, the soldering of their outputs, as well as the reliability of the connections in the connectors and the soldering of the conclusions of the connectors.
To detect a break in the LED lines without disassembling the panel, a current source is required. It is impossible to open transitions connected in series with a simple multimeter; voltage of several tens of volts is necessary.
In cases of attempts to repair the motherboard T.VST59.62, it is necessary to check the operability of the stabilizers or power converters of its microcircuits and, if possible, update the software (software). BGA chips can in most cases be diagnosed by local heating.
Board repair and replacement of CPU chips TSUMV59XU-Z1, Flash 25Q32 are carried out with the necessary equipment, and the corresponding element base. Malfunctions associated with the application of the soldering technology of the BGA processor can be localized by the heating method.
Before changing the tuner CDT-3NP5i1-10, if it is not possible to tune to television channels, make sure that there are supply voltages that must be measured on the corresponding tuner pins.
Attention to the owners! Attempts to repair the TV SUPRA STV-LC22811FL on its own are not recommended by the manufacturer and can lead to serious negative consequences!
FIRMWARE FOR SPI FLASH -----------> SUPRA STV-LC22811FL, Main: T.VST59.62, Panel: 1080p Full HD, 1920x1080
The appearance of MainBoard T.VST59.62 is shown in the figure below:T.VST59.62
It is advisable to start repairing the T.VST59.62 motherboard based on the TSUMV59Xxx multifunction processor by checking the performance of linear voltage stabilizers or voltage converters necessary to provide power to the processor nodes - 1.2V core power, DDR 1.8V memory and Stand-by 3.3V mode . If there is no image, but the display backlight is working properly, you should check the power supply voltage of the LCD panel 5V or 12V, depending on the type of panel used.
T.VST59.62 can be used on TVs:
Akai LEA-22V21M (Panel A215ED1DA3-1), ERISSON 22LEN18 (Panel M215HGJ-L21), ERISSON 16LEN18 (Panel N156BGE-L11 Rev.C1), ERISSON 24LEN18 (Panel M236HGE-L20), Fusion FLTV-16L10B (Panel T156LL10-AW4), FUSION FLTV-24T9 (Panel M240HW01 V.B), FUSION FLTV-16T9 (Panel B156XTN02), FUSION FLTV-16T9D (Panel T156LL10-AW4), HYUNDAI H-LED19V13 (Panel CX185LEDM ), SUPRA STV-LC19811FL (Panel M185XTN01.3), SUPRA STV-LC19820WL (Panel LM185WH2), SUPRA STV-LC22820FL (Panel LS215AFTNM), SUPRA STV-LC18250WL (Panel B173HW02 V.1), SUPRA STV-LC22810FL (Panel M215HGE-L21 Rev.C1), SUPRA STV-LC16810WL (Panel B156RW01 V.1), SUPRA STV-LC18251FL (Panel N173HGE-L11 Rev. C1), SUPRA STV-LC22811FL (Panel 1080p Full HD 1920x1080), SUPRA STV-LC1982WL (Panel 1080p Full HD 1920x1080), TELEFUNKEN TF-LED22S3 (Panel M215HGE-P02).
Main features of the SUPRA STV-LC22811FL device:
Installed matrix (LED-panel) 1080p Full HD, 1920x1080.
To power all internal nodes of the SUPRA STV-LC22811FL TV, an external adapter 12V type is used.
MainBoard - the main board (motherboard) is a T.VST59.62 module, using CPU chips TSUMV59XU-Z1, Flash 25Q322, TDA-1517P, TPS54329 (PWM Step-down), BL8024 (PWM Step-down marker GG .. ) and others.
The tuner CDT-3NP5i1-10 provides reception of television programs and tuning to channels.
LED TV SUPRA STV-LC22811FL with LCD, diagonal size 22 "(56 cm) 16: 9 format. The required brightness of the screen 250 cd / m² is provided by LED backlight LED. Contrast - the ratio of maximum brightness to minimum is 1000: 1 This model uses an LED-panel with the end-face illumination LEDs - Edge LED. TV features include viewing programs and movies in high quality HD at a resolution of 1920x1080 pixels in the graphic resolution of the standard 1080p (Full HD). The input high-frequency or video signal is decoded in analog PAL, SECAM, NTSC systems. Graphic processing and digital signal generation occurs in the standards 480i, 480p, 576i, 576p, 720p, 1080i, 1080p. Supported media file formats: MP3, MPEG4, Xvid, DivX, MKV, JPEG.
The power of the sound system 6 W (2x3 W) provide two speakers. The audio processing system NICAM STEREO is used.
The external interface (communication with other devices) is supported by standard input and output connectors: antenna input (RF), AV, audio x2, component, SCART, VGA, HDMI, USB. An output for connecting headphones is provided. To connect a computer or laptop to this TV model, a VGA (D-Sub 15) connector is used on the TV case, this interface supports resolutions: 640x480, 800x600, 1024x768, 1280x1024, 1360x768, 1920x1080.
The power consumed by the TV in the operating mode from the network is 36 watts.
Overall dimensions: With stand 510x450x160 mm, Without stand 510x360x40 mm.
Mass of the TV: 4.6 kg.
Attention! The panel of a SUPRA STV-LC22811FL LED TV is an expensive and unreliable element.
Avoid any impact on the glass and pressure on the surface of the screen to avoid damage to the LED panel!
It is also unsafe to get liquid on the screen. Sometimes one drop is enough if it flows down the glass onto the cables so that the TV becomes unrepairable.
