REPAIRING AND NOT THROWING AWAY

REPAIRING AND NOT THROWING AWAY

Richtige Fernseher haben Röhren!

Richtige Fernseher haben Röhren!

In Brief: On this site you will find pictures and technical information about Service Modes, Circuit Diagrams, Firmware Update procedure, Disassemble procedure, Universal remote control set-up codes, Troubleshooting and more....

If you go into the profession, you will obtain or have access to a variety of tech tips databases HERE IT IS Master Electronics Repair !.

These are an excellent investment where the saying: 'time-is-money' rules. However, to learn, you need to develop a general troubleshooting approach - a logical, methodical, method of narrowing down the problem. A tech tip database might suggest: 'Replace C536' for a particular symptom. This is good advice for a specific problem on one model. However, what you really want to understand is why C536 was the cause and how to pinpoint the culprit in general even if you don't have a service manual or schematic and your tech tip database doesn't have an entry for your sick TV or VCR.

While schematics are nice, you won't always have them or be able to justify the purchase for a one-of repair. Therefore, in many cases, some reverse engineering will be necessary. The time will be well spent since even if you don't see another instance of the same model in your entire lifetime, you will have learned something in the process that can be applied to other equipment problems.
As always, when you get stuck, checking out a tech-tips database may quickly identify your problem and solution.In that case, you can greatly simplify your troubleshooting or at least confirm a diagnosis before ordering parts.

Happy repairing!
Today, the West is headed for the abyss. For the ultimate fate of our disposable society is for that society itself to be disposed of. And this will happen sooner, rather than later.

How to use the site:
- If you landed here via any Search Engine, you will get what you searched for and you can search more using the search this blog feature provided by Google. You can visit more posts scrolling the left blog archive of all posts of the month/year,
or you can click on the main photo-page to start from the main page. Doing so it starts from the most recent post to the older post simple clicking on the Older Post button on the bottom of each page after reading , post after post.

You can even visit all posts, time to time, when reaching the bottom end of each page and click on the Older Post button.

- If you arrived here at the main page via bookmark you can visit all the site scrolling the left blog archive of all posts of the month/year pointing were you want , or more simple You can even visit all blog posts, from newer to older, clicking at the end of each bottom page on the Older Post button.
So you can see all the blog/site content surfing all pages in it.

- The search this blog feature provided by Google is a real search engine. If you're pointing particular things it will search IT for you; or you can place a brand name in the search query at your choice and visit all results page by page. It's useful since the content of the site is very large.

Note that if you don't find what you searched for, try it after a period of time; the site is a never ending job !

..............The bitterness of poor quality is remembered long after the sweetness of todays funny gadgets low price has faded from memory........ . . . . . .....
Don't forget the past, the end of the world is upon us! Pretty soon it will all turn to dust!

©2010, 2011, 2012, 2013, 2014 Frank Sharp - You do not have permission to copy photos and words from this blog, and any content may be never used it for auctions or commercial purposes, however feel free to post anything you see here with a courtesy link back, btw a link to the original post here , is mandatory.
All posts are presented here for informative, historical and educative purposes as applicable within fair use. NOTHING HERE IS FOR SALE !

Friday, 1 February 2019

APPLE MACBOOK PRO 13 – HOW TO REPLACE HARD DRIVE


Apple MacBook Pro 13 – How to replace Hard drive


Apple MacBook Pro 13 – How to replace Hard drive of Apple MacBook Pro 13 – How to remove the rear cover – How to replace the laptop – How to install OS on new Hard drive – How to clone old drive
Apple MacBook Pro 13:  hard drive replacement procedure 
Remove the following ten screws:
Three 14.4 mm Phillips #00 screwsThree 3.5 mm Phillips #00 screws Four 3.5 mm shouldered Phillips #00 screws
Use your fingers to pry the lower case away from the body of the MacBook near the vent.
Remove the lower case.
Use the edge of a spudger to pry the battery connector upwards from its socket on the logic board. It is useful to pry upward on both short sides of the connector to "walk" it out of its socket. Be careful with the corners of the connectors, they can be easily broken off.
Bend the battery cable slightly away from its socket on the logic board so it does not accidentally connect itself while you work.
Remove the two Phillips screws securing the hard drive bracket to the upper case. These screws will remain attached to the hard drive bracket.
Remove the hard drive bracket. The hard drive bracket may be firmly seated against the upper case.
Use the attached pull tab to lift the hard drive out of the upper case. Don't try to completely remove the hard drive just yet. It is still attached to the hard drive cable.
Pull the hard drive cable away from the body of the hard drive.
Remove the hard drive.
Remove the four 6.0 mm T6 Torx hard drive retaining posts from the sides of the hard drive.
Transfer the hard drive retaining posts to your new hard drive.
If desired, transfer the pull tab over to your new hard drive.
Install operating system and software from scratch
Follow these instructions after physically installing your new hard drive.
# Insert an OS X installation disc into your optical drive.
# Start the computer up on the installation disc by holding down the “option” key while the computer boots.
# Select the installation disc from the menu.
# Select your language and wait for the installer to load.
# Select “Disk Utility” from the Utility drop down menu.
# Select your new hard drive from the left column in Disk Utility.
# Click on the “Erase” tab.
# Choose the Volume format (we recommend “Mac OS Extended (Journaled)”).
# Select a name for the drive.
# Click “Erase.”
# After erasing is done, quit Disk Utility.
# You may now continue with the OS X installation process. If the drive doesn’t show up as an available volume to install the OS onto, restarting the computer should fix the problem. 
Clone your existing hard drive
If you’re happy with your existing operating system installation and simply are upgrading your hard drive capacity, you can clone your existing hard drive to your new drive.
To clone a hard drive, you’ll need a way to connect two hard drives to your Mac. You’ll need to make sure you have an ATA enclosure (IF136-005) if you have a PowerBook or iBook, or a SATA enclosure (IF107-055) if you have a MacBook or MacBook Pro. After you’re done cloning the drive, you can put your old drive in the external enclosure and use it as a backup drive. You can also use an external USB or Firewire backup drive to clone your hard drive. However, in this situation you’ll need to first clone your existing drive to the external drive, and then clone the drive back to your new internal drive.
The following instructions assume you’ll be using an external Firewire enclosure for a laptop drive and SuperDuper. If you’re using a different setup, your installation process may be somewhat different.
# Install your new hard drive in the external Firewire enclosure.
# Connect the Firewire enclosure to your Mac.
# Open Disk Utility.
# Select your new hard drive from the left column in Disk Utility.
# Click on the “Erase” tab.
# Choose the Volume format (we recommend “Mac OS Extended (Journaled)”).
# Select a name for the drive.
# Click “Erase.”
# After erasing is done, quit Disk Utility.
# Your new hard drive should now appear on the computer’s desktop.
# Download and install SuperDuper!
# Open SuperDuper.
# Select your current hard drive in the dropdown menu labeled “Copy.”
# Select your new hard drive in the dropdown menu labeled “to.”
# Select “Backup – all files” in the dropdown menu labeled “using.”
# Click “Copy Now.”
# If prompted, provide your password.
# Wait for the drive to copy (this could take several hours if you have a lot on your hard drive already).
# After the copy is complete, quit SuperDuper.
# At this point, your new hard drive should be loaded with your existing software and ready to install; however, we recommend testing the software installation.
1 Restart the computer while holding down the “option” key.
2 Select your new hard drive from the menu.
3 Wait for the computer to boot up, then verify that everything looks right (make sure you’re actually booting up off the new drive).
4 Your new hard drive is now ready to be installed in your computer.
5 Remove your new hard drive from the external enclosure and install it in your computer.
Posted By: FRANK at 01:39
TAG: ,