REPAIRING AND NOT THROWING AWAY

REPAIRING AND NOT THROWING AWAY

Richtige Fernseher haben Röhren!

Richtige Fernseher haben Röhren!

In Brief: On this site you will find pictures and technical information about Service Modes, Circuit Diagrams, Firmware Update procedure, Disassemble procedure, Universal remote control set-up codes, Troubleshooting and more....

If you go into the profession, you will obtain or have access to a variety of tech tips databases HERE IT IS Master Electronics Repair !.

These are an excellent investment where the saying: 'time-is-money' rules. However, to learn, you need to develop a general troubleshooting approach - a logical, methodical, method of narrowing down the problem. A tech tip database might suggest: 'Replace C536' for a particular symptom. This is good advice for a specific problem on one model. However, what you really want to understand is why C536 was the cause and how to pinpoint the culprit in general even if you don't have a service manual or schematic and your tech tip database doesn't have an entry for your sick TV or VCR.

While schematics are nice, you won't always have them or be able to justify the purchase for a one-of repair. Therefore, in many cases, some reverse engineering will be necessary. The time will be well spent since even if you don't see another instance of the same model in your entire lifetime, you will have learned something in the process that can be applied to other equipment problems.
As always, when you get stuck, checking out a tech-tips database may quickly identify your problem and solution.In that case, you can greatly simplify your troubleshooting or at least confirm a diagnosis before ordering parts.

Happy repairing!
Today, the West is headed for the abyss. For the ultimate fate of our disposable society is for that society itself to be disposed of. And this will happen sooner, rather than later.

How to use the site:
- If you landed here via any Search Engine, you will get what you searched for and you can search more using the search this blog feature provided by Google. You can visit more posts scrolling the left blog archive of all posts of the month/year,
or you can click on the main photo-page to start from the main page. Doing so it starts from the most recent post to the older post simple clicking on the Older Post button on the bottom of each page after reading , post after post.

You can even visit all posts, time to time, when reaching the bottom end of each page and click on the Older Post button.

- If you arrived here at the main page via bookmark you can visit all the site scrolling the left blog archive of all posts of the month/year pointing were you want , or more simple You can even visit all blog posts, from newer to older, clicking at the end of each bottom page on the Older Post button.
So you can see all the blog/site content surfing all pages in it.

- The search this blog feature provided by Google is a real search engine. If you're pointing particular things it will search IT for you; or you can place a brand name in the search query at your choice and visit all results page by page. It's useful since the content of the site is very large.

Note that if you don't find what you searched for, try it after a period of time; the site is a never ending job !

..............The bitterness of poor quality is remembered long after the sweetness of todays funny gadgets low price has faded from memory........ . . . . . .....
Don't forget the past, the end of the world is upon us! Pretty soon it will all turn to dust!

©2010, 2011, 2012, 2013, 2014 Frank Sharp - You do not have permission to copy photos and words from this blog, and any content may be never used it for auctions or commercial purposes, however feel free to post anything you see here with a courtesy link back, btw a link to the original post here , is mandatory.
All posts are presented here for informative, historical and educative purposes as applicable within fair use. NOTHING HERE IS FOR SALE !

Thursday 28 February 2019

HOW TO DISASSEMBLE DELL LAPTOP – DELL ALIENWARE 15 – SETP BY STEP DISASSEMBLING PROCEDURE – HOW TO REMOVE THE BASE – HOW TO REMOVE THE KEY BOARD – LAPTOP REPAIR AND SERVICE

How to disassemble Dell laptop – Dell Alienware 15 – Setp by step disassembling procedure – How to remove the base – How to remove the key board – Laptop repair and service

Category: Laptop repair and Service 

Contents of this article 

  • How to remove the keyboard 
  • How to remove HDD
  • How to remove the case  

Dell  Alienware 15 

DISASSEMBLING PROCEDURE 
How to remove the base panel
Procedure
1. Close the display and turn the computer over.
2. Loosen the captive screws that secure the base panel to the computer base.
3. Using a plastic scribe, gently release the tabs that secure the base panel to the computer base.
4. Slide and remove the base panel from the computer base.
1. computer base 2 captive screws (2)
3. base panel 4 plastic scribe
5. Disconnect the battery cable from the system board.
1. battery cable
6. Turn the computer over and open the display as far as possible.
7. Press and hold the power button for 4 seconds to ground the system board. How to remove the memory modules
Procedure
1. Using your fingertips, carefully spread apart the securing clips on each end of the memory-module slot until the memory module pops up.
2. Slide and remove the memory module from the memory-module slot.
1 securing clips (2)
2 memory modules (2)
3 memory-module slot
How to remove the solid-state drives
Procedure
1. Remove the screw that secures the solid-state drive to the computer base.
2. Slide and remove the solid-state drive from the solid-state drive slot.
1 screw
2 solid-state drive slot
3 solid-state drives (2)
How to remove the hard drive
Procedure
1. Remove the keyboard-backlight cable, keyboard cable, and macro-keys cable from the routing guides on the computer base.
1. macro-keys cable
2. keyboard cable
3. keyboard-backlight cable
4. routing guides (3)
5. hard-drive assembly 6 computer base
2. Remove the screws that secure the hard-drive assembly to the computer base.
3. Using the pull tab, disconnect the hard-drive cable from the system board.
4. Note the hard-drive cable routing and remove the cable from the routing guides on the computer base.
5. Lift and slide the hard-drive assembly off the computer base.
1. pull tab
2. hard-drive cable
3. screws (4)
4. hard-drive assembly
6. Remove the screws that secure the hard-drive bracket to the hard-drive assembly.
How to remove palm rest
Procedure
1. Remove the keyboard cable, keyboard-backlight cable, and macro-keys cable from the routing guides on the computer base.
2. Lift the latches and disconnect the keyboard-backlight cable, keyboard cable, macro-keys cable, and macro-keys backlight cable from the system board.
1. keyboard-backlight cable
2. routing guides (3)
3. latches (4)
4. keyboard cable
5. macro-keys backlight cable 6 macro-keys cable
3. Remove the screws that secure the palm-rest assembly to the computer base.
1. screws (15)
2. computer base
4. Turn the computer over and open the display as far as possible.
5. Lift the computer base and rest the display on a clean and flat surface.
6. Push the palm-rest assembly from the release hole to release it from the tabs on the computer base.
1. palm-rest assembly 2 computer base
3. release hole
7. Place the computer in an upright position.
8. Using a plastic scribe, pry up along the edges of the palm-rest assembly.
9. Gently lift the palm-rest assembly and remove the keyboard cable, keyboard-backlight cable, macro-keys cable, and macro-keys backlight cable from the slot on the computer base.
1. palm-rest assembly
2. plastic scribe
10. Carefully turn the palm-rest assembly over and disconnect the power button board cable from the system board.
11. Lift the palm-rest assembly off the computer base.
1. palm-rest assembly
2. computer base
3. power-button board cable
How to remove keyboard
Procedure
1. Lift the latches and disconnect the touch-pad cable and the status-light
cable from the power-button board.
2. Note the touch-pad cable and status-light cable routings and peel off the cables from the keyboard bracket.
1. latches (2)
2. touch-pad cable
3. status-light cable
4. keyboard bracket
3. Remove the screws that secure the keyboard bracket to the palm-rest assembly
1. keyboard bracket
2. screws (8)
4. Lift the keyboard bracket at an angle and remove it from the tabs on the palm-rest assembly.
1. keyboard bracket
2. palm-rest assembly
3. tabs (3)
5. Remove the screws that secure the keyboard to the palm-rest assembly.
1. keyboard
2. screws (2)
6. Lift the keyboard at an angle and remove it from the tabs on the palm-rest assembly.
1. palm-rest assembly
2. keyboard
3. tabs (5)
Posted By: FRANK at 07:08
TAG: , ,