REPAIRING AND NOT THROWING AWAY

REPAIRING AND NOT THROWING AWAY

Richtige Fernseher haben Röhren!

Richtige Fernseher haben Röhren!

In Brief: On this site you will find pictures and technical information about Service Modes, Circuit Diagrams, Firmware Update procedure, Disassemble procedure, Universal remote control set-up codes, Troubleshooting and more....

If you go into the profession, you will obtain or have access to a variety of tech tips databases HERE IT IS Master Electronics Repair !.

These are an excellent investment where the saying: 'time-is-money' rules. However, to learn, you need to develop a general troubleshooting approach - a logical, methodical, method of narrowing down the problem. A tech tip database might suggest: 'Replace C536' for a particular symptom. This is good advice for a specific problem on one model. However, what you really want to understand is why C536 was the cause and how to pinpoint the culprit in general even if you don't have a service manual or schematic and your tech tip database doesn't have an entry for your sick TV or VCR.

While schematics are nice, you won't always have them or be able to justify the purchase for a one-of repair. Therefore, in many cases, some reverse engineering will be necessary. The time will be well spent since even if you don't see another instance of the same model in your entire lifetime, you will have learned something in the process that can be applied to other equipment problems.
As always, when you get stuck, checking out a tech-tips database may quickly identify your problem and solution.In that case, you can greatly simplify your troubleshooting or at least confirm a diagnosis before ordering parts.

Happy repairing!
Today, the West is headed for the abyss. For the ultimate fate of our disposable society is for that society itself to be disposed of. And this will happen sooner, rather than later.

How to use the site:
- If you landed here via any Search Engine, you will get what you searched for and you can search more using the search this blog feature provided by Google. You can visit more posts scrolling the left blog archive of all posts of the month/year,
or you can click on the main photo-page to start from the main page. Doing so it starts from the most recent post to the older post simple clicking on the Older Post button on the bottom of each page after reading , post after post.

You can even visit all posts, time to time, when reaching the bottom end of each page and click on the Older Post button.

- If you arrived here at the main page via bookmark you can visit all the site scrolling the left blog archive of all posts of the month/year pointing were you want , or more simple You can even visit all blog posts, from newer to older, clicking at the end of each bottom page on the Older Post button.
So you can see all the blog/site content surfing all pages in it.

- The search this blog feature provided by Google is a real search engine. If you're pointing particular things it will search IT for you; or you can place a brand name in the search query at your choice and visit all results page by page. It's useful since the content of the site is very large.

Note that if you don't find what you searched for, try it after a period of time; the site is a never ending job !

..............The bitterness of poor quality is remembered long after the sweetness of todays funny gadgets low price has faded from memory........ . . . . . .....
Don't forget the past, the end of the world is upon us! Pretty soon it will all turn to dust!

©2010, 2011, 2012, 2013, 2014 Frank Sharp - You do not have permission to copy photos and words from this blog, and any content may be never used it for auctions or commercial purposes, however feel free to post anything you see here with a courtesy link back, btw a link to the original post here , is mandatory.
All posts are presented here for informative, historical and educative purposes as applicable within fair use. NOTHING HERE IS FOR SALE !

Tuesday 26 February 2019

SONY TRINITRTON WEGA - [KV-TG21L70 _ KV-TG21M80 _ KV-TG21P55] - FAILS TO SWITCH ON EVEN WITH REPEATED ATTEMPTS.

SONY TRINITRTON WEGA - [KV-TG21L70 _ KV-TG21M80 _ KV-TG21P55] -fFAILS TO SWITCH ON EVEN WITH REPEATED ATTEMPTS.


Set fails to switch ON even after repeated switch OFF and switch ON; by its front panel power ON/OFF button, or by power ON button on remote control.

There are two possiblilites for this fault
The first  is with failure of 9VDC regulator [IC604 - PQ 09RD11]; or loose solder terminals to this IC.
     Check wether the standby light comes On, at least for a moment, when you switch ON the TV by its front panel power switch.  If yes, make sure that 5VDC and 9VDC supply rails are OK.  If not, check the voltage at the cathode of [D609] at SMPS power supply section.  If there is voltage at this point, check the voltage at pin number [1] of regulator IC stated above.  If there is no voltage found, check and repalce [R614 & R625].  If there is voltage at pin number [1] of the regulator IC, and there is no voltage at pin [3] of that IC, check the voltage at pin [4] (control).  This pin is connected by a 1K resistor to pin number [3] of main system IC (Standby). If there is no voltage at the output to this 9V regulator IC, means this is a bad one.  It must get a control voltage from main system control IC pin [3]; approximately 4.5VDC, to switch it On and to supply the 9VDC output.  So before repalce it, make sure that this control voltage is there or not.
If not; is the second case.
     Check the voltage at pin number 64 of main system IC.  It should be 5VDC.  If this voltage is absent, Check the voltages at the reset cum regulator IC [MM 1319AFBE].  The pin voltages to this IC  are;
Pin number 1 = 0V [Ground]
Pin number 2 = 4.6VDC [Reset voltage]
Pin number 3 = 4.6VDC [Reference voltage]
Pin number 4 = 11VDC [Supply in]
Pin number 5 = 5VDC [Output voltage from IC to supply main system control IC]
Pin number 6 = 0V [Ground]
Pin number 7 = free
Pin number 8 = Free.

     Check the voltages to these pins, especially to pins 4&5.  If there is no voltage at pin-4 check the supply rail from SMPS for any break.  If there is voltage at this pin-4 and not voltage at pin 5 (5VDC out); make sure that this IC is faulty.  Replace it with same number.
     Check the voltage at pin number 2 of this IC.  It is connected with pin number 36 of main system control IC via a 1k resistor. The pin number 36 of main system control IC is the reset pin [Strobe].  If this pin do not get a voltage, the microcomputer IC [system control IC] will not start up, and this is the fault to the set
Repalcing the the RESET IC stated above will solve the problem.
In my service experience, I've replaced several of this reset cum regualtor ICs, for this fault.
Be very carefull to take voltages to both main system control and rest ICs.  Never make a short circuit with meter probes with adjecent close soder terminals.  It may migh make main system control too to get damaged.
Posted By: FRANK at 06:09
TAG: , , ,