REPAIRING AND NOT THROWING AWAY

REPAIRING AND NOT THROWING AWAY

Richtige Fernseher haben Röhren!

Richtige Fernseher haben Röhren!

In Brief: On this site you will find pictures and technical information about Service Modes, Circuit Diagrams, Firmware Update procedure, Disassemble procedure, Universal remote control set-up codes, Troubleshooting and more....

If you go into the profession, you will obtain or have access to a variety of tech tips databases HERE IT IS Master Electronics Repair !.

These are an excellent investment where the saying: 'time-is-money' rules. However, to learn, you need to develop a general troubleshooting approach - a logical, methodical, method of narrowing down the problem. A tech tip database might suggest: 'Replace C536' for a particular symptom. This is good advice for a specific problem on one model. However, what you really want to understand is why C536 was the cause and how to pinpoint the culprit in general even if you don't have a service manual or schematic and your tech tip database doesn't have an entry for your sick TV or VCR.

While schematics are nice, you won't always have them or be able to justify the purchase for a one-of repair. Therefore, in many cases, some reverse engineering will be necessary. The time will be well spent since even if you don't see another instance of the same model in your entire lifetime, you will have learned something in the process that can be applied to other equipment problems.
As always, when you get stuck, checking out a tech-tips database may quickly identify your problem and solution.In that case, you can greatly simplify your troubleshooting or at least confirm a diagnosis before ordering parts.

Happy repairing!
Today, the West is headed for the abyss. For the ultimate fate of our disposable society is for that society itself to be disposed of. And this will happen sooner, rather than later.

How to use the site:
- If you landed here via any Search Engine, you will get what you searched for and you can search more using the search this blog feature provided by Google. You can visit more posts scrolling the left blog archive of all posts of the month/year,
or you can click on the main photo-page to start from the main page. Doing so it starts from the most recent post to the older post simple clicking on the Older Post button on the bottom of each page after reading , post after post.

You can even visit all posts, time to time, when reaching the bottom end of each page and click on the Older Post button.

- If you arrived here at the main page via bookmark you can visit all the site scrolling the left blog archive of all posts of the month/year pointing were you want , or more simple You can even visit all blog posts, from newer to older, clicking at the end of each bottom page on the Older Post button.
So you can see all the blog/site content surfing all pages in it.

- The search this blog feature provided by Google is a real search engine. If you're pointing particular things it will search IT for you; or you can place a brand name in the search query at your choice and visit all results page by page. It's useful since the content of the site is very large.

Note that if you don't find what you searched for, try it after a period of time; the site is a never ending job !

..............The bitterness of poor quality is remembered long after the sweetness of todays funny gadgets low price has faded from memory........ . . . . . .....
Don't forget the past, the end of the world is upon us! Pretty soon it will all turn to dust!

©2010, 2011, 2012, 2013, 2014 Frank Sharp - You do not have permission to copy photos and words from this blog, and any content may be never used it for auctions or commercial purposes, however feel free to post anything you see here with a courtesy link back, btw a link to the original post here , is mandatory.
All posts are presented here for informative, historical and educative purposes as applicable within fair use. NOTHING HERE IS FOR SALE !

Monday, 4 February 2019

SYMPHONIC WF2703 CRT TV - HOW TO ENTER SERVICE MODE – ADJUSTMENTS – SMPS AND DEFLECTION CIRCUIT DIAGRAM - 27" CTV

Symphonic WF2703 CRT TV - How to enter service mode – adjustments – SMPS and deflection circuit diagram - 27" CTV

Electrical adjustments are required after replacing circuit components and certain mechanical parts. It is important to perform these adjustments, after all repairs and replacements have been completed. Also, do not attempt these adjustments unless the proper equipment is available.
Test Equipment Required
1. NTSC Pattern Generator (Color Bar W/White Window, Red Color, Dot Pattern, Gray Scale, Monoscope, Multi-Burst)
2. DC Voltmeter
3. Oscilloscope: Dual-trace with 10:1 probe,
V-Range:0.001~50V/Div,
F-Range:DC~AC-60MHz
4. Plastic Tip Driver
5. Remote control unit:Part No. N0127UD or N0132UD or N0105UD or N0108UD
6. DC power supply 13.2V/5A
How to make Service remote control unit
1. Prepare normal remote control unit. (Part No. N0127UD or N0132UD or N0105UD or N0108UD)
Remove 3 Screws from the back lid. (Fig. 1-1)
2. Add J1 (Jumper Wire) to the remote control CBA. (Fig. 1-2)
DC 120V Adjustment
Purpose: To obtain correct operation.
Symptom of Misadjustment: The picture is dark and the unit does not operate correctly.
Note: TP601, TP300(GND), VR661 --- Main CBA
1. Connect DC Volt Meter to TP601 and TP300(GND).
2. Adjust VR661 so that the voltage of TP601 becomes +120±0.5V DC.
SMPS (Power Supply) and Deflection circuit diagrams [Click on the pictures to magnify]
CAUTION
Fixed voltage ( or Auto voltage selectable ) power supply circuit is used in this unit.  If Main Fuse (F601) is blown, check to see that all components in the power supply circuit are not defective before you connect the AC plug to the AC power supply. Otherwise it may cause some components in the power supply circuit to fail.
Service mode adjustments
Black Strech Control Adjustment
Purpose: To show the fine black color.
Symptom of Misadjustment: Black color will not appear correctly.
Note: Use Service remote control unit.
1. Enter the Service mode. (See page 5-1)
2. Press " 6 " button on the Service remote control unit. " B-S " is indicated.
3. Press " CH ▲/▼"buttons on the Service remote control unit so that display will change " OFF ", " 0", " 1 ", " 2 " and " 3 ". Then choose " B-S OFF ".
4. Press " 6 " button on the Service remote control unit. " B-S*2 " is indicated.
5. Press " CH ▲/▼" buttons on the Service remote control unit so that display will change " 0 " and " 1 ". Then choose " B-S*2 0".
6. Turn the power off and on again. (Main power button on the TV unit.).
Setting for 7F and FRENCH data Values
General
1. Enter the Service mode.
2. Press " VOL ▼" button on the Service remote control unit. Display changes " C/D ", " 7F ", " FRENCH
", " ACCESS CODE ", " STEREO ", " VIDEO TONE ", " FM-MODE ", and " V-OUT " cyclically when " VOL  ▼" button is pressed.
7F
1. Press " VOL ▼" button on the Service remote control unit. Then select 7F display.
2. Press " CH ▲/▼" buttons on the Service remote control unit. Then choose 7F=FF
FRENCH
1. Press " VOL ▼" button on the Service remote control unit. Then select FRENCH display.
2. Press " CH ▲/▼" buttons on the Service remote control unit. Then choose FRENCH=OFF.
ACCESS CODE ---- set to OFF
VIDEO TONE ---- set to ON
FM-MODE ---- set to OFF
V-OUT ---- set to OFF
STEREO ---- set to ON
Note: C/D and VCO data values do not need to be adjusted at this moment.
Setting for CONTRAST, COLOR, TINT, V-TINT and SHARP data Values
General
1. Enter the Service mode.
2. Press " MENU " button on the Service remote control unit. Display changes " BRIGHT ", " CONTRAST "," COLOR ", " TINT ", " V-TINT " and " SHARP "
cyclically when " MENU " button is pressed.
CONTRAST (CNT)
1. Press " MENU " button on the Service remote control unit. Then select " CONTRAST " (CNT) display.
2. Press " CH ▲/▼" buttons on the Service remote control unit so that the value of " CONTRAST "(CNT) becomes 84.
COLOR (CLR)
1. Press " MENU " button on the Service remote control unit. Then select " COLOR " (CLR) display.
2. Press " CH ▲/▼" buttons on the Service remote control unit so that the value of " COLOR " (CLR) becomes 58.
TINT (TNT)
1. Press " MENU " button on the Service remote control unit. Then select " TINT " (TNT) display.
2. Press " CH ▲/▼" buttons on the Service remote control unit so that the value of " TINT " (TNT) becomes 62.
V-TINT (V-TNT)
1. Press " MENU " button on the Service remote control unit. Then select " V-TINT " (V-TNT) display.
2. Press " CH  ▲/▼" buttons on the Service remote control unit so that the value of " V-TINT " (V-TNT) becomes 59
SHARP (SHARP)
1. Press " MENU " button on the Service remote control unit. Then select " SHARP " (SHARP) display.
2. Press " CH ▲/▼" buttons on the Service remote control unit so that the value of “ SHARP " (SHARP) becomes 47.
Note: BRIGHT data value does not need to be adjusted at this moment.
 Black Level Adjustment
Purpose: Set Black Level
Symptom of Misadjustment: 
If black level is incorrect, Proper brightness can not be obtained by adjusting the Brightness Control.
1. Enter the Service mode. 
2. Press " MENU " button on the Service remote control unit and select " BRT "mode. (Display changes " BRT ", " CNT ", " CLR ", " TNT ", " V-TNT ", and
" SHARP " cyclically when MENU button is pressed).
3. Press " CH ▲/▼" buttons on the Service remote control unit so that the value of " BRT " becomes 128.
4. Turn the power off and on again. (Main power button on the TV unit.)
Posted By: FRANK at 04:00
TAG: , , ,