PHILIPS BDP5012/F7 FIRMWARE UPDATE INITIALIZATION AND POWER SUPPLY
PHILIPS BDP5012/F7
FIRMWARE UPDATE INITIALIZATION AND POWER SUPPLY
HOW TO EJECT THE DISC MANUALLY
1. Remove the Top Cover and Front Assembly.
2. Insert a screwdriver, hexagon wrench to push the Portion A.
3. Pull the tray out manually and remove a disc.
1. Remove the Top Cover and Front Assembly.
2. Insert a screwdriver, hexagon wrench to push the Portion A.
3. Pull the tray out manually and remove a disc.
HOW INITIALIZE THE BLU-RAY DISC PLAYER
To put the program back at the factory-default, initialize the BD player as the following procedure.
1. Turn the power on.
2. Remove the disc on the tray and close the tray.
3. Press [1], [2], [3], [4], and [INFO] buttons on the remote control unit in that order.4. Press [ STOP ] button on the remote control unit.
CLEAR WILL DISPLAY
5. To exit this mode, press [ POWER ] button.
5. To exit this mode, press [ POWER ] button.
FIRMWARE RENEWAL MODE
Note: The file extension of the available
firmware is “b20”.
1. Turn the power on and remove the disc on the tray and close the tray.
2. To put the BD player into version up mode, press [9], [8], [7], [6], and [DISC MENU/POP UP MENU] buttons on the remote control unit in that order.
The tray will open automatically.
1. Turn the power on and remove the disc on the tray and close the tray.
2. To put the BD player into version up mode, press [9], [8], [7], [6], and [DISC MENU/POP UP MENU] buttons on the remote control unit in that order.
The tray will open automatically.
3. Load the disc
for version up.
4. The BD player enters the F/W version up mode automatically. Make sure to insert the proper F/W for the state of this model.
4. The BD player enters the F/W version up mode automatically. Make sure to insert the proper F/W for the state of this model.
5. After
programming is finished, the checksum on the VFD .
6. Unplug the AC
cord from the AC outlet. Then plug it again.
7. Turn the power on.
8. Press [1], [2], [3], [4], and [INFO] buttons on the remote control unit in that order.
7. Turn the power on.
8. Press [1], [2], [3], [4], and [INFO] buttons on the remote control unit in that order.
9. Press [ STOP ]
button on the remote control unit.
10. To exit this
mode, press [POWER ] button.
How to Verify the Firmware Version
1. Turn the power on.
2. Remove the disc on the tray and close the tray.
3. Press [1], [2], [3], [4], and [INFO] buttons on the remote control unit in that order.
4. To exit this mode, press [ POWER ] button.
1. Turn the power on.
2. Remove the disc on the tray and close the tray.
3. Press [1], [2], [3], [4], and [INFO] buttons on the remote control unit in that order.
4. To exit this mode, press [ POWER ] button.
HOW TO RENEW THE FIRMWARE
1. Press [HOME]
to display Home menu.
2. Select to Settings - Advanced Setup - Others - Software Upgrade.
3. F/W Upgrade will appear on the screen, then select Yes
2. Select to Settings - Advanced Setup - Others - Software Upgrade.
3. F/W Upgrade will appear on the screen, then select Yes
4.Insert the disc
and press [OPEN/CLOSE].
5. Disc loading
starts.
6. UPDATE WILL
DISPLAY ON THE SCREEN AND VFD
7. F/W loading
starts
8. Updating
starts automatically. Wait until installation complete
9. SHUTDOWN on
the VFD and turn the power off automatically when it finishes.
10. The power turns on and the tray will open automatically. Remove the disc on the tray. All the Settings will be kept as they were.
10. The power turns on and the tray will open automatically. Remove the disc on the tray. All the Settings will be kept as they were.
POWER SUPPLY CIRCUIT
CLICK ON THE IMAGE TO ZOOM IN
The
laser bream is emitted for the location shown in picture. when checking
the laser diode , be sure to keep the eyes at least 30 cm away from the
pickup lens when the diode is turned on . Do not look directly at the
laser beam.
CAUTION :
use of controls and adjustments,or doing procedure other than
those specified herein , may result in hazardous radiation
exposure.
TOP PICTURE OF BD MECHANISM
