SHARP LC20D42U - LCD TV - HOW TO UPGRADE THE FIRMWARE - SERVICE MODE
How to upgrade the Firmware - Sharp LCD TV LC-20D42U
ADJUSTMENT PROCEDURE
The adjustment values are set to the optimum conditions at the
factory before shipping. If a value should become improper or an adjustment is
required due to part replacement, make an adjustment according to the following
procedure.
After replacement of any PWB unit
and/or IC for repair, note the following.
When replacing the following units, make sure to prepare the new units loaded with updated software. MAIN Unit:DUNKE001FMF1
When replacing the following units, make sure to prepare the new units loaded with updated software. MAIN Unit:DUNKE001FMF1
UPGRADING OF EACH MICROPROCESSOR SOFTWARE
Caution: Never "POWER OFF" the unit when software
upgrade is ongoing. Otherwise the system
may be damaged beyond recovery.
Software version upgrade
The model employs the following software.
Main Software
Monitor microprocessor software.
The main software and the monitor microprocessor software can be upgraded by using a general-purpose USB Memory.
The followings are the procedures for upgrading, explained separately for each of the main software, the monitor microprocessor software.
Main Software
Monitor microprocessor software.
The main software and the monitor microprocessor software can be upgraded by using a general-purpose USB Memory.
The followings are the procedures for upgrading, explained separately for each of the main software, the monitor microprocessor software.
MAIN SOFTWARE VERSION UPGRADE
Get ready before you start.
> USB Memory of 128MB or higher capacity.
> PC running on Windows 98/98SE/ME/2000/XP operating system.
> USB Memory reader/writer with USB connectivity.
> PC running on Windows 98/98SE/ME/2000/XP operating system.
> USB Memory reader/writer with USB connectivity.
Preparations
To upgrade the main software, it is necessary to get ready the USB
Memory for version upgrade before you start.
Follow the steps below and create the USB Memory for version
upgrade.
> Copy the file 42LTAxxx.USB(named temporarily) for version
upgrade to the root directory (folder) of the USB Memory.
NOTE: In the USB Memory drive, do not store other folders or unrelated files, or more than one files for version upgrade. Now the USB Memory for version upgrade is ready.
NOTE: In the USB Memory drive, do not store other folders or unrelated files, or more than one files for version upgrade. Now the USB Memory for version upgrade is ready.
HOW TO UPGRADE THE SOFTWARE
> Unplug the AC cord. (Make sure AC power shut down more than 1
minute.)
> Insert the USB Memory for version upgrade (prepared as above) into the service socket located Right side from center at terminals, above HDMI4 terminal in the rear of the unit.
>> Plug in the AC cord with power button pressing after 5 seconds later, release the power button. [SERVICE MODE]
> After the unit start-up, the system upgrade screen as shown below appears within 20-40 seconds.
> Insert the USB Memory for version upgrade (prepared as above) into the service socket located Right side from center at terminals, above HDMI4 terminal in the rear of the unit.
>> Plug in the AC cord with power button pressing after 5 seconds later, release the power button. [SERVICE MODE]
> After the unit start-up, the system upgrade screen as shown below appears within 20-40 seconds.
Even a single failure in the process will trigger the upgrade
failure screen as shown below. the word "NG" changes to red for the
item failed.
NOTE: In the event of a failure, repeat the upgrading process. If the process repeatedly fails. it is likely that the hardware is troubled.
NOTE: In the event of a failure, repeat the upgrading process. If the process repeatedly fails. it is likely that the hardware is troubled.
> Unplug the AC cord and remove the USB Memory for version
upgrade. Now the software version upgrade is complete.
NOTE: When you are done with the software version upgrade, start the set, go to the top page of the adjustment process screen and check the main software version information.
NOTE: When you are done with the software version upgrade, start the set, go to the top page of the adjustment process screen and check the main software version information.
MONITOR MICROPROCESSOR SOFTWARE UPGRADE
Create the USB memory for monitor microprocessor software
version upgrade in the same manner as explained in the "Main software
version upgrade". Copy the file
42LTMxxx.USB and 42LTMxxx.BIN(named temporarily ) for monitor microprocessor
software version upgrade to the USB memory.
How to upgrade the software
> Unplug the AC cord.(make sure AC power shut down more than 1
minute.)
> Insert the USB memory for version upgrade (prepared as above) into the service socket located Right side from center at terminals, above HDMI4 terminal in the rear of the unit.
> Insert the USB memory for version upgrade (prepared as above) into the service socket located Right side from center at terminals, above HDMI4 terminal in the rear of the unit.
> Plug in the AC cord while the power button pressing. After 5 seconds, release the power button. [SERVICE MODE]
CAUTION: The moment this operation is done, the upgrading of the
monitor microprocessor software starts. While the upgrade is ongoing, never
power off the unit. Otherwise the upgrade will fail and the system may have a
serious damage beyond recovery (inability to start). After the monitor microprocessor software is
upgrade, should perform the "Industry Init " by all mean.
> After the upgrade start-up, the power light will flash
continuous.
> A failure in the process will trigger the upgrade failure
screen. The word "NG" changes to red for the item failed.
NOTE: In the event of
a failure, repeat the upgrading process. If the process repeatedly fails, it is
likely that the hardware is troubled.
> Upon completion of the whole process, the set will restart
automatically.
> Unplug the AC cord and remove the USB Memory for version upgrade. Now the software version upgrade is complete.
NOTE: When you are done with the software version upgrade, start the set, go to the top page of the adjustment process screen and check the monitor microprocessor software version information and panel size information.
> Unplug the AC cord and remove the USB Memory for version upgrade. Now the software version upgrade is complete.
NOTE: When you are done with the software version upgrade, start the set, go to the top page of the adjustment process screen and check the monitor microprocessor software version information and panel size information.
LCD TV ADJUSTMENT ITEM
MICON SOFTWARE Writing
Monitor Micon and Main Micon software writing (Main PWB :
QPWBXE001WJN1)
Adjustment item > Software writing
Adjustment conditions > Inspection mode
file version checking.
Adjustment procedure > Connect the tool
by using write MAIN soft to P9301 (TL9301,TL9302,TL9310 - TL9355,TL9357,
TL9359,TL9375,TL9378,TL9380 - TL9383) that is mounted on the main PWB, and
insert USB Memory by using MONITOR MICON to main PWB.MONITOR connect to
TL8123,TL8124 that denoted figure. Load stated voltage to MAIN PWB, write the latest
version MAIN SOFT to IC8451, and write the MONITOR MICON SOFT to IC2002, after
all completed, turn off the AC power.
NOTE: When the USB MEMORY can't insert to main PWB or read out is error, MAIN Miro software must be write again.
NOTE: When the USB MEMORY can't insert to main PWB or read out is error, MAIN Miro software must be write again.