Janome Sewing machine error codes causes and solution
Janome
Sewing machine error codes causes and solution - Troubleshooting tips - Janome
MB4 - Janome MC15000 - Janome MC12000 - Janome MC11000S / MC11000 - Janome
MC9900 - Janome MC350E / MC300E - Janome
MC10001 / MC10000 - Janome MC8900QCP - Janome MC7700QCP
Janome Sewing Machine
Janome MB4
E:00
Please
power down and restart again. (Communication error with the RCS. The machine
won’t display this error on the RCS. Instead the screen will not go to the next
step from the ‘Welcome screen’.)
1. Check the connection going from the RCS plug into the RCS unit and the connector on the machine to the ‘B’ board.
2. Try another RCS unit to determine which part is the problem.
E:01
1. Check the connection going from the RCS plug into the RCS unit and the connector on the machine to the ‘B’ board.
2. Try another RCS unit to determine which part is the problem.
E:01
Please
power down and restart again. (There is a problem with a stepping motor not
initializing correctly or at all.)
1. With the machine off, manually move the head to needle #4, push the carriage unit all of the way to the front and to the right. Turn on the machine and see which doesn’t calibrate.
2. While holding down the Start/Stop & Reverse buttons, turn on the machine. Release the buttons once you see icons on the screen:
A. Press “Phase” then ‘All Init’ to calibrate the machine, then press “Cancel”.
B. Check the “Needle” and press the left & right arrow keys to bring the needle to #4 then back to #1 to check the step motor & sensors. Press “Cancel” to exit.
C. Press “Pick-Up” and press “Init” to check the thread catcher. Press “Cancel” to exit.
D. Press “Sensor Solenoid” and press “Solenoid1” to check [QQQQQQ] and “Solenoid2” to check [QQQQQQ]. Press “Cancel” to exit.
E. Press “Cut Motor” and press “Init” to calibrate the dynamic cutter. Now press “Divide” then “Init” once again to check the cutter.
E:02:
1. With the machine off, manually move the head to needle #4, push the carriage unit all of the way to the front and to the right. Turn on the machine and see which doesn’t calibrate.
2. While holding down the Start/Stop & Reverse buttons, turn on the machine. Release the buttons once you see icons on the screen:
A. Press “Phase” then ‘All Init’ to calibrate the machine, then press “Cancel”.
B. Check the “Needle” and press the left & right arrow keys to bring the needle to #4 then back to #1 to check the step motor & sensors. Press “Cancel” to exit.
C. Press “Pick-Up” and press “Init” to check the thread catcher. Press “Cancel” to exit.
D. Press “Sensor Solenoid” and press “Solenoid1” to check [QQQQQQ] and “Solenoid2” to check [QQQQQQ]. Press “Cancel” to exit.
E. Press “Cut Motor” and press “Init” to calibrate the dynamic cutter. Now press “Divide” then “Init” once again to check the cutter.
E:02:
Please
power down and restart again. (Needle bar changeover.)
1. Remove the stationary cover then turn the hand wheel to 270°. Using a 2.5mm hex driver, turn the silver gear on the needle-change step motor to move the head from needle bar #1 to #4 then back to #1 to check for any binds. If there is a bind, adjust ‘head play’ as shown in the service manual.
2. Check and adjust ‘moving head stop position’ and ‘needle stop position’ as shown in the service manual.
E:03
1. Remove the stationary cover then turn the hand wheel to 270°. Using a 2.5mm hex driver, turn the silver gear on the needle-change step motor to move the head from needle bar #1 to #4 then back to #1 to check for any binds. If there is a bind, adjust ‘head play’ as shown in the service manual.
2. Check and adjust ‘moving head stop position’ and ‘needle stop position’ as shown in the service manual.
E:03
Needle
bar is out of position. Press OK to move the needle bar to switching position.
(Needle bar change over phase.)
3. Remove the stationary cover then turn the hand wheel to 270°. Using a 2.5mm hex driver, turn the silver gear on the needle-change step motor to move the head from needle bar #1 to #4 then back to #1 to check for any binds. If there is a bind, adjust ‘head play’ as shown in the service manual.
4. Check and adjust ‘moving head stop position’ and ‘needle stop position’ as shown in the service manual.
E:04
3. Remove the stationary cover then turn the hand wheel to 270°. Using a 2.5mm hex driver, turn the silver gear on the needle-change step motor to move the head from needle bar #1 to #4 then back to #1 to check for any binds. If there is a bind, adjust ‘head play’ as shown in the service manual.
4. Check and adjust ‘moving head stop position’ and ‘needle stop position’ as shown in the service manual.
E:04
Lock!!.
(There is a problem with the DC Motor.)
1. Clean the sensor on the DC motor and check if the shield plate on the motor is not loose or hitting the sensor. If either the sensor or shield plate is damaged, replace the motor.
2. Try resetting the DC motor. Hold down the Forward & Bobbin Winder buttons on the RCS unit then turn on the machine. Press the button called “Clear”. Turn off the machine.
E:05
1. Clean the sensor on the DC motor and check if the shield plate on the motor is not loose or hitting the sensor. If either the sensor or shield plate is damaged, replace the motor.
2. Try resetting the DC motor. Hold down the Forward & Bobbin Winder buttons on the RCS unit then turn on the machine. Press the button called “Clear”. Turn off the machine.
E:05
Rethread
and start. (Either the machine broke the thread or it thinks the thread is
broken.)
1. Remove any thread, then the tension unit cover. Now run the machine and quickly spin the small wheel by hand (depending on which needle is being ‘sewn’). If it still gives you the error, check the connections or replace the circuit board.
2. If you do not get the error, check: needle position (left-right & front-back), needle bar height, presser bar height, hook timing, and clearance.
E:06
1. Remove any thread, then the tension unit cover. Now run the machine and quickly spin the small wheel by hand (depending on which needle is being ‘sewn’). If it still gives you the error, check the connections or replace the circuit board.
2. If you do not get the error, check: needle position (left-right & front-back), needle bar height, presser bar height, hook timing, and clearance.
E:06
[Deleted]
E:07
E:07
Please
power down and restart again. (The thread cutter malfunctioned.)
1. Check the connections and any binds in the thread cutter linkage. Replace the dynamic thread cutter unit if necessary.
E:08
1. Check the connections and any binds in the thread cutter linkage. Replace the dynamic thread cutter unit if necessary.
E:08
Pull
the tension release lever. (The lever that opens the tension discs may be
engaged.)
1. Make sure the lever is not engaged (keeping the tension discs open) and check the connections.
2. Remove the tension unit cover and check the position of the microswitch. Adjust the position of this microswitch. Replace the microswitch if necessary.
E:09
1. Make sure the lever is not engaged (keeping the tension discs open) and check the connections.
2. Remove the tension unit cover and check the position of the microswitch. Adjust the position of this microswitch. Replace the microswitch if necessary.
E:09
Please
power down and restart again. (The driving motor malfunctioned.)
Replace DC Motor
1. While holding down the Bobbin Winder & Forward buttons on the RCS, turn on the machine.
2. Once a menu appears on the screen, release the buttons. Press ‘Clear’.
3. Turn the machine off then back on like normal.
Replace DC Motor
1. While holding down the Bobbin Winder & Forward buttons on the RCS, turn on the machine.
2. Once a menu appears on the screen, release the buttons. Press ‘Clear’.
3. Turn the machine off then back on like normal.
Janome MC15000
Raise
Presser Foot and Needle Bar, then turn power on again.
1. Turn the machine off and attach the carriage unit.
2. Raise the needle bar to the highest position and push the needle bar to the left.
3. Open the embroidery arm and push the carriage all of the way out towards the back and to the left.
4. Put your ear up the machine and then turn it on. Listen for which step motor ‘stutters’ or does not calibrate. Follow the service book to adjusting/replacing the specific unit.
Warning (with a picture showing you to attach the needle plate):
1. The needle plate is not attached properly.
2. The needle plate micro switch needs to be adjusted.
Please make sure the proper presser foot is attached.
1. The needle plate is not attached properly.
2. The needle plate micro switch needs to be adjusted.
Rethread and start.
1. The machine ran out of thread.
2. There is a problem with the thread check sensor on the tension unit.
Bobbin thread may not be sufficient. Bobbin winding is recommended.
1. The bobbin is almost empty.
2. The remaining bobbin thread sensor needs to be adjusted in the test mode.
Check bobbin winder.
1. The bobbin winder is not pushed to the left (engaged).
2. The bobbin winder connection is not plugged in.
Pull down BH Lever.
1. The buttonhole lever is not lowered all the way before sewing a buttonhole.
2. The shield plate is not in the center of the sensor.
3. The buttonhole sensor connection is not plugged in.
Warning! The embroidery unit is attached/detached. Please turn off the power and then on again.
1. The embroidery unit was connected or disconnected while the machine was on. Turn the machine off then back on again to reset the machine.
Warning: Is something stuck in machine? Is cloth too thick? Is needle bent? Check the above and restart.
1. Replace the foot controller.
2. The machine may be jammed. Remove the timing belt to locate whether the bind is on the upper shaft or lower shaft. If it is the upper shaft, there may be thread caught in the take-up lever or crank pin. If the lower shaft is binding, check hook clearance, hook backlash.
3. If you continue to have the problem, loosen the screws that hold the metal, lower shaft supporter. While the machine is running slow-to-medium speed, tighten the screws.
4. Clean the sensor on the DC motor and check if the shield plate on the motor is not loose or hitting the sensor. If either the sensor or shield plate is damaged, replace the motor.
5. Clean the lower shaft sensor and make sure the shield plate going thru this sensor is not hitting the sides of the sensor.
6. If you still get the error, replace the DC motor or lower shaft sensor (in this order).
1. Turn the machine off and attach the carriage unit.
2. Raise the needle bar to the highest position and push the needle bar to the left.
3. Open the embroidery arm and push the carriage all of the way out towards the back and to the left.
4. Put your ear up the machine and then turn it on. Listen for which step motor ‘stutters’ or does not calibrate. Follow the service book to adjusting/replacing the specific unit.
Warning (with a picture showing you to attach the needle plate):
1. The needle plate is not attached properly.
2. The needle plate micro switch needs to be adjusted.
Please make sure the proper presser foot is attached.
1. The needle plate is not attached properly.
2. The needle plate micro switch needs to be adjusted.
Rethread and start.
1. The machine ran out of thread.
2. There is a problem with the thread check sensor on the tension unit.
Bobbin thread may not be sufficient. Bobbin winding is recommended.
1. The bobbin is almost empty.
2. The remaining bobbin thread sensor needs to be adjusted in the test mode.
Check bobbin winder.
1. The bobbin winder is not pushed to the left (engaged).
2. The bobbin winder connection is not plugged in.
Pull down BH Lever.
1. The buttonhole lever is not lowered all the way before sewing a buttonhole.
2. The shield plate is not in the center of the sensor.
3. The buttonhole sensor connection is not plugged in.
Warning! The embroidery unit is attached/detached. Please turn off the power and then on again.
1. The embroidery unit was connected or disconnected while the machine was on. Turn the machine off then back on again to reset the machine.
Warning: Is something stuck in machine? Is cloth too thick? Is needle bent? Check the above and restart.
1. Replace the foot controller.
2. The machine may be jammed. Remove the timing belt to locate whether the bind is on the upper shaft or lower shaft. If it is the upper shaft, there may be thread caught in the take-up lever or crank pin. If the lower shaft is binding, check hook clearance, hook backlash.
3. If you continue to have the problem, loosen the screws that hold the metal, lower shaft supporter. While the machine is running slow-to-medium speed, tighten the screws.
4. Clean the sensor on the DC motor and check if the shield plate on the motor is not loose or hitting the sensor. If either the sensor or shield plate is damaged, replace the motor.
5. Clean the lower shaft sensor and make sure the shield plate going thru this sensor is not hitting the sides of the sensor.
6. If you still get the error, replace the DC motor or lower shaft sensor (in this order).
Janome MC12000
Raise
Presser Foot and Needle Bar, then turn power on again.
1. Turn the machine off and attach the carriage unit.
2. Raise the needle bar to the highest position and push the needle bar to the left.
3. Open the embroidery arm and push the carriage all of the way out towards the back and to the left.
4. Put your ear up the machine and then turn it on. Listen for which step motor ‘stutters’ or does not calibrate. Follow the service book to adjusting/replacing the specific unit.
Warning (with a picture showing you to attach a needle plate):
1. The needle plate is not attached properly.
2. The needle plate micro switch needs to be adjusted.
Stop for Safety Purposes:
1. Replace the foot controller.
2. Check for a tight or stuck clutch by the hand wheel.
3. The machine may be jammed. Remove the timing belt to locate whether the bind is on the upper shaft or lower shaft. If it is the upper shaft, there may be thread caught in the take-up lever or crank pin. If the lower shaft is binding, check hook clearance, hook backlash.
4. If you continue to have the problem, loosen the screws that hold the metal, lower shaft supporter. While the machine is running slow-to-medium speed, tighten the screws.
5. Clean the sensor on the DC motor and check if the shield plate on the motor is not loose or hitting the sensor. If either the sensor or shield plate is damaged, replace the motor.
6. Clean the lower shaft sensor and make sure the shield plate going thru this sensor is not hitting the sides of the sensor.
7. If you still get the error, replace the DC motor or lower shaft sensor (in this order)
1. Turn the machine off and attach the carriage unit.
2. Raise the needle bar to the highest position and push the needle bar to the left.
3. Open the embroidery arm and push the carriage all of the way out towards the back and to the left.
4. Put your ear up the machine and then turn it on. Listen for which step motor ‘stutters’ or does not calibrate. Follow the service book to adjusting/replacing the specific unit.
Warning (with a picture showing you to attach a needle plate):
1. The needle plate is not attached properly.
2. The needle plate micro switch needs to be adjusted.
Stop for Safety Purposes:
1. Replace the foot controller.
2. Check for a tight or stuck clutch by the hand wheel.
3. The machine may be jammed. Remove the timing belt to locate whether the bind is on the upper shaft or lower shaft. If it is the upper shaft, there may be thread caught in the take-up lever or crank pin. If the lower shaft is binding, check hook clearance, hook backlash.
4. If you continue to have the problem, loosen the screws that hold the metal, lower shaft supporter. While the machine is running slow-to-medium speed, tighten the screws.
5. Clean the sensor on the DC motor and check if the shield plate on the motor is not loose or hitting the sensor. If either the sensor or shield plate is damaged, replace the motor.
6. Clean the lower shaft sensor and make sure the shield plate going thru this sensor is not hitting the sides of the sensor.
7. If you still get the error, replace the DC motor or lower shaft sensor (in this order)
Janome MC11000S
/ MC11000
Raise
Presser Foot and Needle Bar then Turn Machine on Again
1. Turn the machine off. Raise the needle bar to the highest position and raise the presser foot.
2. Open the embroidery arm. *Slowly & firmly*, move the carriage all the way towards the back and all the way to the left.
1. Turn the machine off. Raise the needle bar to the highest position and raise the presser foot.
2. Open the embroidery arm. *Slowly & firmly*, move the carriage all the way towards the back and all the way to the left.
3. Push
the needle bar to the left.
4. Open the face plate. Lower the needle threader only half-way down by manually turning the black threaded bar. (See the diagram on the inside of the face plate.)
5. Turn the machine on. The carriage should return to the home position, the needle bar will center itself, the needle threader will return to the up position, and the tension unit will calibrate. If you still get an error, check to see which does not calibrate. Check the connections, any binds, clean the gears, etc. If the error pops up on the screen only after 10 seconds or you hear a highpitched ‘screeching’ or ‘whining’ sound, you have a problem with the feed dog drop step motor. Check the connections, thread caught in the gears, any binds, etc., or replace the unit.
Lock
There’s a problem with the DC motor. Check the connections and make sure the shield plate going thru its sensor and is not loose or touching the sides of the sensor. Make sure both the shield plate and sensor are not damaged. If either the shield plate or sensor is damaged or you still get the “Lock” error, replace the DC motor.
Raise Presser Foot (when the presser foot is down and you try to run the machine)
There’s a problem with the feed dog drop step motor. Check the connections, thread caught in the gears, any binds, etc., or replace the unit.
Low Bobbin Thread (you need the green & red bobbin gauges [#00310KGAUGE] to fix this):
1. With the machine off, hold down the Start/Stop & Reverse buttons, then turn the machine on.
2. Press ‘Bobbin’.
3. Insert the red bobbin gauge. Press ‘Key’ until you get the most common number, then press ‘MEM1’.
4. Remove the green gauge and Insert the red gauge. Press ‘Key’ until you get the most common number, then press ‘MEM2’.
5. Press ‘X’ to save it and turn the machine off.
Presser Foot (P)
1. Go into embroidery mode and select any built-in design.
2. Attach the ‘P’ foot and lower the presser bar.
3. Locate the "L"-shaped bracket directly underneath the large, metal bracket that the handle pivots on.
4. On older models, you can loosen the Phillips screw next to the c-clip and push the "L"-shaped bracket slightly downwards. Do not push the bracket towards the front of the machine too much,
as it will hit the needle bar supporter and cause a loud ‘clacking’ sound.
5. On newer models, there will not be a Phillips screw, so you will need to loosen the Phillips screw that holds the sensor this "L"-shaped bracket goes into and move it slightly towards the back of the machine.
These are very fine adjustments. You do not have to turn the machine off each time an adjustment is made. Just press the ‘Start/Stop’ button each time an adjustment is made.
4. Open the face plate. Lower the needle threader only half-way down by manually turning the black threaded bar. (See the diagram on the inside of the face plate.)
5. Turn the machine on. The carriage should return to the home position, the needle bar will center itself, the needle threader will return to the up position, and the tension unit will calibrate. If you still get an error, check to see which does not calibrate. Check the connections, any binds, clean the gears, etc. If the error pops up on the screen only after 10 seconds or you hear a highpitched ‘screeching’ or ‘whining’ sound, you have a problem with the feed dog drop step motor. Check the connections, thread caught in the gears, any binds, etc., or replace the unit.
Lock
There’s a problem with the DC motor. Check the connections and make sure the shield plate going thru its sensor and is not loose or touching the sides of the sensor. Make sure both the shield plate and sensor are not damaged. If either the shield plate or sensor is damaged or you still get the “Lock” error, replace the DC motor.
Raise Presser Foot (when the presser foot is down and you try to run the machine)
There’s a problem with the feed dog drop step motor. Check the connections, thread caught in the gears, any binds, etc., or replace the unit.
Low Bobbin Thread (you need the green & red bobbin gauges [#00310KGAUGE] to fix this):
1. With the machine off, hold down the Start/Stop & Reverse buttons, then turn the machine on.
2. Press ‘Bobbin’.
3. Insert the red bobbin gauge. Press ‘Key’ until you get the most common number, then press ‘MEM1’.
4. Remove the green gauge and Insert the red gauge. Press ‘Key’ until you get the most common number, then press ‘MEM2’.
5. Press ‘X’ to save it and turn the machine off.
Presser Foot (P)
1. Go into embroidery mode and select any built-in design.
2. Attach the ‘P’ foot and lower the presser bar.
3. Locate the "L"-shaped bracket directly underneath the large, metal bracket that the handle pivots on.
4. On older models, you can loosen the Phillips screw next to the c-clip and push the "L"-shaped bracket slightly downwards. Do not push the bracket towards the front of the machine too much,
as it will hit the needle bar supporter and cause a loud ‘clacking’ sound.
5. On newer models, there will not be a Phillips screw, so you will need to loosen the Phillips screw that holds the sensor this "L"-shaped bracket goes into and move it slightly towards the back of the machine.
These are very fine adjustments. You do not have to turn the machine off each time an adjustment is made. Just press the ‘Start/Stop’ button each time an adjustment is made.
Janome MC9900
Raise
Presser Foot and Needle Bar, then turn power on again.
1. Turn the machine off and attach the carriage unit.
2. Raise the needle bar to the highest position and push the needle bar to the left.
3. Open the embroidery arm and push the carriage all of the way out towards the back and to the left.
4. Put your ear up the machine and then turn it on. Listen for which step motor ‘stutters’ or does not calibrate. Follow the service book to adjusting/replacing the specific unit.
Warning (with a picture showing you to attach a needle plate):
1. The needle plate is not attached properly.
2. The needle plate micro switch needs to be adjusted.
Please make sure the proper presser foot is attached.
1. Remove the needle plate
Bobbin thread may not be sufficient. Bobbin winding is recommended.
1. The bobbin thread is almost empty.
2. The remaining bobbin thread sensor needs to be adjusted in the test mode.
Lower the Presser Foot.
1. The position of the presser foot up/down micro switch needs to be adjusted.
2. The presser foot up/down micro switch may be unplugged or plugged into the wrong connection on the ‘A’ board.
Please attach the P Foot
1. The wrong foot is on the machine.
2. The ‘P’ foot sensor may need to be adjusted.
Lower the Feed Dog.
1. The feed dog drop lever may not be activating/deactivating the micro switch.
2. The drop feed plate by the hook race may be bent causing it to bind.
Pull down BH Lever.
1. The buttonhole lever is not lowered all the way before sewing a buttonhole.
2. The shield plate is not in the center of the sensor.
3. The buttonhole sensor connection is not plugged in.
Rethread and start.
1. The machine ran out of thread.
2. There is a problem with the thread check sensor on the tension unit.
Turn off the machine and attach the embroidery unit.
1. The embroidery unit was connected or disconnected while the machine was on. Turn the machine off then back on again to reset the machine.
Warning: Is something stuck in machine? Is cloth too thick? Is needle bent? Check the above and restart.
1. Replace the foot controller.
2. The machine may be jammed. Remove the timing belt to locate whether the bind is on the upper shaft or lower shaft. If it is the upper shaft, there may be thread caught in the take-up lever or crank pin. If the lower shaft is binding, check hook clearance, hook backlash.
3. If you continue to have the problem, loosen the screws that hold the metal, lower shaft supporter. While the machine is running slow-to-medium speed, tighten the screws.
Clean the sensor on the DC motor and check if the shield plate on the motor is not loose or hitting the sensor. If either the sensor or shield plate is damaged, replace the motor.
4. Clean the lower shaft sensor and make sure the shield plate going thru this sensor is not hitting the sides of the sensor.
5. If you still get the error, replace the DC motor or lower shaft sensor (in this order)
1. Turn the machine off and attach the carriage unit.
2. Raise the needle bar to the highest position and push the needle bar to the left.
3. Open the embroidery arm and push the carriage all of the way out towards the back and to the left.
4. Put your ear up the machine and then turn it on. Listen for which step motor ‘stutters’ or does not calibrate. Follow the service book to adjusting/replacing the specific unit.
Warning (with a picture showing you to attach a needle plate):
1. The needle plate is not attached properly.
2. The needle plate micro switch needs to be adjusted.
Please make sure the proper presser foot is attached.
1. Remove the needle plate
Bobbin thread may not be sufficient. Bobbin winding is recommended.
1. The bobbin thread is almost empty.
2. The remaining bobbin thread sensor needs to be adjusted in the test mode.
Lower the Presser Foot.
1. The position of the presser foot up/down micro switch needs to be adjusted.
2. The presser foot up/down micro switch may be unplugged or plugged into the wrong connection on the ‘A’ board.
Please attach the P Foot
1. The wrong foot is on the machine.
2. The ‘P’ foot sensor may need to be adjusted.
Lower the Feed Dog.
1. The feed dog drop lever may not be activating/deactivating the micro switch.
2. The drop feed plate by the hook race may be bent causing it to bind.
Pull down BH Lever.
1. The buttonhole lever is not lowered all the way before sewing a buttonhole.
2. The shield plate is not in the center of the sensor.
3. The buttonhole sensor connection is not plugged in.
Rethread and start.
1. The machine ran out of thread.
2. There is a problem with the thread check sensor on the tension unit.
Turn off the machine and attach the embroidery unit.
1. The embroidery unit was connected or disconnected while the machine was on. Turn the machine off then back on again to reset the machine.
Warning: Is something stuck in machine? Is cloth too thick? Is needle bent? Check the above and restart.
1. Replace the foot controller.
2. The machine may be jammed. Remove the timing belt to locate whether the bind is on the upper shaft or lower shaft. If it is the upper shaft, there may be thread caught in the take-up lever or crank pin. If the lower shaft is binding, check hook clearance, hook backlash.
3. If you continue to have the problem, loosen the screws that hold the metal, lower shaft supporter. While the machine is running slow-to-medium speed, tighten the screws.
Clean the sensor on the DC motor and check if the shield plate on the motor is not loose or hitting the sensor. If either the sensor or shield plate is damaged, replace the motor.
4. Clean the lower shaft sensor and make sure the shield plate going thru this sensor is not hitting the sides of the sensor.
5. If you still get the error, replace the DC motor or lower shaft sensor (in this order)
Janome MC350E
/ MC300E
Raise
Presser Foot and Needle Bar then Turn Machine on Again
You have a problem with the base unit. Check for any pinched wires, thread caught in the gears, or binds in the base. If you have pinched wires, you need to replace the sensor and/or step motor the wires go to and also the ‘A’ board.
1. The machine may be jammed. Check for any black ‘gunk’ by the right side bushing on the upper shaft. If there is any ‘gunk’ there, replace both the upper shaft & rear bushing.
2. Check for thread caught in the take-up lever/crank pin area.
3. Clean the sensor on the DC motor and check if the shield plate on the motor is not loose or hitting the sensor. If either the sensor or shield plate is damaged, replace the motor.
4. Check the upper shaft sensor. Make sure the shield plates are going perfectly thru the middle of the sensor. Replace the sensor if damaged.
5. Check the connections. If everything looks OK but you still get the error, replace the DC motor.
You have a problem with the base unit. Check for any pinched wires, thread caught in the gears, or binds in the base. If you have pinched wires, you need to replace the sensor and/or step motor the wires go to and also the ‘A’ board.
1. The machine may be jammed. Check for any black ‘gunk’ by the right side bushing on the upper shaft. If there is any ‘gunk’ there, replace both the upper shaft & rear bushing.
2. Check for thread caught in the take-up lever/crank pin area.
3. Clean the sensor on the DC motor and check if the shield plate on the motor is not loose or hitting the sensor. If either the sensor or shield plate is damaged, replace the motor.
4. Check the upper shaft sensor. Make sure the shield plates are going perfectly thru the middle of the sensor. Replace the sensor if damaged.
5. Check the connections. If everything looks OK but you still get the error, replace the DC motor.
Janome MC10001
/ MC10000
01
Base
Unit.
A. Remove the base unit from the machine.
B. Check the connections especially for pinched wires.
C. Remove the 2 step motors from the base. Clean all of the gears thoroughly and lubricate them with white lithium grease
D. Service the base by lubricating all moving parts.
When reattaching the step motors, be sure to push them away from the gears when tightening the screws. Replace the base unit (first) or ‘A’ board if you still have problems.
02
A. Remove the base unit from the machine.
B. Check the connections especially for pinched wires.
C. Remove the 2 step motors from the base. Clean all of the gears thoroughly and lubricate them with white lithium grease
D. Service the base by lubricating all moving parts.
When reattaching the step motors, be sure to push them away from the gears when tightening the screws. Replace the base unit (first) or ‘A’ board if you still have problems.
02
Zigzag
Motor.
A. Check the connections.
B. With the machine off, push the needle bar to the left & right several times. You should just feel the friction of the step motor.
C. Check for thread caught in the gears and clean zigzag motor sensor.
D. Replace the zigzag motor if necessary.
04
A. Check the connections.
B. With the machine off, push the needle bar to the left & right several times. You should just feel the friction of the step motor.
C. Check for thread caught in the gears and clean zigzag motor sensor.
D. Replace the zigzag motor if necessary.
04
Feed
Step Motor.
A. Check the connections.
B. With the machine off, and the presser foot up, push the triangle-shaped, large, black feed step motor gear back & forth several times. You should just feel the friction of the step motor and no binds in the feed system.
C. Check for thread caught in the gears and clean feed step motor sensor.
D. Replace the feed step motor if necessary.
08
A. Check the connections.
B. With the machine off, and the presser foot up, push the triangle-shaped, large, black feed step motor gear back & forth several times. You should just feel the friction of the step motor and no binds in the feed system.
C. Check for thread caught in the gears and clean feed step motor sensor.
D. Replace the feed step motor if necessary.
08
Tension
Unit.
A. Check the connections.
B. Reset the tension by turning the small, flat-head screw on the side of the tension unit counter-clockwise until it stops (do not overturn it!). Now turn the screw clockwise 16 ‘clicks’.
C. If it continues to jam, replace the tension unit.
10
A. Check the connections.
B. Reset the tension by turning the small, flat-head screw on the side of the tension unit counter-clockwise until it stops (do not overturn it!). Now turn the screw clockwise 16 ‘clicks’.
C. If it continues to jam, replace the tension unit.
10
Needle
Threader Motor Unit.
A. Turn off the machine and open the face plate.
B. Lower the needle threader only half-way down by manually turning the black threader bar, then turn the machine on to reset it the unit.
If it continues to jam, check the connections or replace the entire unit.
A. Turn off the machine and open the face plate.
B. Lower the needle threader only half-way down by manually turning the black threader bar, then turn the machine on to reset it the unit.
If it continues to jam, check the connections or replace the entire unit.
If
you do not see any error number on the lower-right or lower-left section of the
error screen, perform the following:
1. Turn the machine off.
2. Raise the needle bar to the highest position and raise the presser foot.
3. Open the embroidery arm. *Slowly & firmly*, move the carriage all the way towards the back and all the way to the left.
4. Push the needle bar to the left.
5. Open the face plate. Lower the needle threader only half-way down by manually turning the black threaded bar. (See the diagram on the inside of the face plate).
6. Turn the machine on. The carriage should return to the home position, the needle bar will center itself, the needle threader will return to the up position, and the tension unit will calibrate. If
you still get an error, check to see which does not calibrate. Check the connections, any binds, clean the gears, etc.
Is Needle Bent, Fabric too Thick.
1. The machine may be jammed. Check for any black ‘gunk’ by the right side bushing on the upper shaft. If there is any ‘gunk’ there, replace both the upper shaft & rear bushing.
2. Clean the sensor on the DC Motor and check if the shield plate on the motor is loose or hitting the sensor. If either the sensor or shield plate is damaged, replace the motor.
3. Check & clean the upper shaft sensor. Make sure the shield plates are going perfectly thru the middle of the sensor. Replace the sensor and/or shield plate if there is damage.
4. Check the connections. If everything looks OK but you still get the error, replace the DC motor.
1. Turn the machine off.
2. Raise the needle bar to the highest position and raise the presser foot.
3. Open the embroidery arm. *Slowly & firmly*, move the carriage all the way towards the back and all the way to the left.
4. Push the needle bar to the left.
5. Open the face plate. Lower the needle threader only half-way down by manually turning the black threaded bar. (See the diagram on the inside of the face plate).
6. Turn the machine on. The carriage should return to the home position, the needle bar will center itself, the needle threader will return to the up position, and the tension unit will calibrate. If
you still get an error, check to see which does not calibrate. Check the connections, any binds, clean the gears, etc.
Is Needle Bent, Fabric too Thick.
1. The machine may be jammed. Check for any black ‘gunk’ by the right side bushing on the upper shaft. If there is any ‘gunk’ there, replace both the upper shaft & rear bushing.
2. Clean the sensor on the DC Motor and check if the shield plate on the motor is loose or hitting the sensor. If either the sensor or shield plate is damaged, replace the motor.
3. Check & clean the upper shaft sensor. Make sure the shield plates are going perfectly thru the middle of the sensor. Replace the sensor and/or shield plate if there is damage.
4. Check the connections. If everything looks OK but you still get the error, replace the DC motor.
Janome MC8900QCP
E1
Zigzag
Motor:
1. Check the connections.
2. With the machine off, push the needle bar to the left & right several times. You should just feel the friction of the step motor.
3. Check for thread caught in the gears and clean zigzag motor sensor.
4. Replace the zigzag motor if necessary.
E2
1. Check the connections.
2. With the machine off, push the needle bar to the left & right several times. You should just feel the friction of the step motor.
3. Check for thread caught in the gears and clean zigzag motor sensor.
4. Replace the zigzag motor if necessary.
E2
Feed
Step Motor:
1. Check the connections.
2. With the machine off, and the presser foot up, push the triangle-shaped, large, black feed step motor gear back & forth several times. You should just feel the friction of the step motor and no binds in the feed system.
3. Check for thread caught in the gears and clean feed step motor sensor.
4. Replace the feed step motor if necessary.
E4
1. Check the connections.
2. With the machine off, and the presser foot up, push the triangle-shaped, large, black feed step motor gear back & forth several times. You should just feel the friction of the step motor and no binds in the feed system.
3. Check for thread caught in the gears and clean feed step motor sensor.
4. Replace the feed step motor if necessary.
E4
Thread
Cutter Motor:
1. Check the connections.
2. Check & clean the gears.
3. Check the position of the microswitch and adjust if necessary.
4. If you still get the error, replace the thread cutter motor.
E6
1. Check the connections.
2. Check & clean the gears.
3. Check the position of the microswitch and adjust if necessary.
4. If you still get the error, replace the thread cutter motor.
E6
Could
Not Detect Feed Phase:
1. Clean the lower shaft sensor
2. The lower shaft shield plate set screw may be loose. Make sure the shield plates are going perfectly thru the middle of the sensor then tighten the screw.
3. Replace the sensor and/or shield plate if damaged.
Stop for Safety Purposes:
1. Replace the foot controller.
2. Check for a tight or stuck clutch by the hand wheel.
3. The machine may be jammed. Remove the timing belt to locate whether the bind is on the upper shaft or lower shaft. If it is the upper shaft, there may be thread caught in the take-up lever or
crank pin. If the lower shaft is binding, check hook clearance & hook backlash.
4. If you continue to have the problem, loosen the screws that hold the metal, lower shaft supporter. While the machine is running slow-to-medium speed, tighten the screws.
5. Clean the sensor on the DC motor and check if the shield plate on the motor is not loose or hitting the sensor. If either the sensor or shield plate is damaged, replace the motor.
6. Clean the lower shaft sensor and make sure the shield plate going thru this sensor is not hitting the sides of the sensor.
7. If you still get the error, replace the DC motor or lower shaft sensor (in this order).
Warning: Is something stuck in machine? Is cloth too thick? Is needle bent? Check the above and restart.:
1. The machine may be jammed. Remove the timing belt to locate whether the bind is on the upper shaft or lower shaft. If it is the upper shaft, there may be thread caught in the take-up lever or
crank pin. If the lower shaft is binding, check hook clearance, hook backlash.
2. If you continue to have the problem, loosen the screws that hold the metal, lower shaft supporter. While the machine is running slow-to-medium speed, tighten the screws.
3. Clean the sensor on the DC motor and check if the shield plate on the motor is not loose or hitting the sensor. If either the sensor or shield plate is damaged, replace the motor.
4. Clean the upper shaft sensor and make sure the shield plate going thru this sensor is not hitting the sides of the sensor.
5. If you still get the error, replace the DC motor or upper shaft sensor (in this order).
Pull down BH Lever:
1. Clean the lower shaft sensor
2. The lower shaft shield plate set screw may be loose. Make sure the shield plates are going perfectly thru the middle of the sensor then tighten the screw.
3. Replace the sensor and/or shield plate if damaged.
Stop for Safety Purposes:
1. Replace the foot controller.
2. Check for a tight or stuck clutch by the hand wheel.
3. The machine may be jammed. Remove the timing belt to locate whether the bind is on the upper shaft or lower shaft. If it is the upper shaft, there may be thread caught in the take-up lever or
crank pin. If the lower shaft is binding, check hook clearance & hook backlash.
4. If you continue to have the problem, loosen the screws that hold the metal, lower shaft supporter. While the machine is running slow-to-medium speed, tighten the screws.
5. Clean the sensor on the DC motor and check if the shield plate on the motor is not loose or hitting the sensor. If either the sensor or shield plate is damaged, replace the motor.
6. Clean the lower shaft sensor and make sure the shield plate going thru this sensor is not hitting the sides of the sensor.
7. If you still get the error, replace the DC motor or lower shaft sensor (in this order).
Warning: Is something stuck in machine? Is cloth too thick? Is needle bent? Check the above and restart.:
1. The machine may be jammed. Remove the timing belt to locate whether the bind is on the upper shaft or lower shaft. If it is the upper shaft, there may be thread caught in the take-up lever or
crank pin. If the lower shaft is binding, check hook clearance, hook backlash.
2. If you continue to have the problem, loosen the screws that hold the metal, lower shaft supporter. While the machine is running slow-to-medium speed, tighten the screws.
3. Clean the sensor on the DC motor and check if the shield plate on the motor is not loose or hitting the sensor. If either the sensor or shield plate is damaged, replace the motor.
4. Clean the upper shaft sensor and make sure the shield plate going thru this sensor is not hitting the sides of the sensor.
5. If you still get the error, replace the DC motor or upper shaft sensor (in this order).
Pull down BH Lever:
If
the lever is already down and you get this message perform the following:
1. Remove the face plate, remove any foot on the machine, and pull down the buttonhole lever.
2. Follow the lever all of the way up where it turns into a shield plate with a thin ‘slit’ in the middle. This slit should be perfectly (may be tweaked to work better) in the middle of the sensor.
3. If an adjustment is necessary, locate the 1.5mm hex screw sticking out of a silver, locknut. Turn this screw to push the shield plate towards the front or back to align the plate to the sensor.
4. Check the connections and replace the buttonhole sensor if necessary.
Stop for Safety Purposes (with a picture showing you to attach a needle plate):
1. Remove the needle plate, bed cover, free arm cover, then reattach the needle plate.
2. Loosen the 2x 2.0mm set screws that hold the needle plate micro switch towards the back of the needle plate.
3. Push the micro switch up all of the way until it stops then very slightly down. Tighten the screws.
4. If you still get the error, replace the micro switch unit.
1. Remove the face plate, remove any foot on the machine, and pull down the buttonhole lever.
2. Follow the lever all of the way up where it turns into a shield plate with a thin ‘slit’ in the middle. This slit should be perfectly (may be tweaked to work better) in the middle of the sensor.
3. If an adjustment is necessary, locate the 1.5mm hex screw sticking out of a silver, locknut. Turn this screw to push the shield plate towards the front or back to align the plate to the sensor.
4. Check the connections and replace the buttonhole sensor if necessary.
Stop for Safety Purposes (with a picture showing you to attach a needle plate):
1. Remove the needle plate, bed cover, free arm cover, then reattach the needle plate.
2. Loosen the 2x 2.0mm set screws that hold the needle plate micro switch towards the back of the needle plate.
3. Push the micro switch up all of the way until it stops then very slightly down. Tighten the screws.
4. If you still get the error, replace the micro switch unit.
Janome MC7700QCP
Before
you do anything to this machine, check if the machine has the new, updated ‘A’
board.
1. Remove the belt cover.
2. Take a peak in from the side of the machine where all of the wires are going into the ‘A’ board. If every single wire plugs into the board and you see no wires that are ‘glued’ or ‘soldered’ on to the board, replace the ‘A’ board with the new, updated version. The updated board has 2 sets of wires that are ‘glued’ or ‘soldered’ on with grey paste.
F1
1. Remove the belt cover.
2. Take a peak in from the side of the machine where all of the wires are going into the ‘A’ board. If every single wire plugs into the board and you see no wires that are ‘glued’ or ‘soldered’ on to the board, replace the ‘A’ board with the new, updated version. The updated board has 2 sets of wires that are ‘glued’ or ‘soldered’ on with grey paste.
F1
Microswitch
for Needle Plate Step Motor:
1. Remove the needle plate and press ‘D1S’. If you don’t get the error, replace the needle plate unit.
2. If you still get the error, replace the Needle Plate Step Motor Unit.
F2
1. Remove the needle plate and press ‘D1S’. If you don’t get the error, replace the needle plate unit.
2. If you still get the error, replace the Needle Plate Step Motor Unit.
F2
Center
Needle Position Sensor. The sensor is not aligned with the slit on the zigzag
rod when the needle is in center position of the needle plate.
1. When in straight-stitch, center-needle position, make sure the needle is perfectly in the middle of the hole of the needle plate. Adjust if necessary.
2. If you still get the error, go to ‘D1S’ anyway.
3. On the zigzag rod on the top of the machine, just to the left of the zigzag motor is the center needle position sensor. Verify the sensor is perfectly thru the middle of the sensor. Adjust if necessary.
4. If you still get the error, replace the Center Needle Position Sensor.
E1
1. When in straight-stitch, center-needle position, make sure the needle is perfectly in the middle of the hole of the needle plate. Adjust if necessary.
2. If you still get the error, go to ‘D1S’ anyway.
3. On the zigzag rod on the top of the machine, just to the left of the zigzag motor is the center needle position sensor. Verify the sensor is perfectly thru the middle of the sensor. Adjust if necessary.
4. If you still get the error, replace the Center Needle Position Sensor.
E1
Zigzag
Motor:
1. Check the connections.
2. With the machine off, push the needle bar to the left & right several times. You should just feel the friction of the step motor.
3. Check for thread caught in the gears and clean zigzag motor sensor.
4. Replace the zigzag motor if necessary.
E2
1. Check the connections.
2. With the machine off, push the needle bar to the left & right several times. You should just feel the friction of the step motor.
3. Check for thread caught in the gears and clean zigzag motor sensor.
4. Replace the zigzag motor if necessary.
E2
Feed
Step Motor:
1. Check the connections.
2. With the machine off, and the presser foot up, push the triangle-shaped, large, black feed step motor gear back & forth several times. You should just feel the friction of the step motor and no binds in the feed system.
3. Check for thread caught in the gears and clean feed step motor sensor.
4. Replace the feed step motor if necessary.
E3
1. Check the connections.
2. With the machine off, and the presser foot up, push the triangle-shaped, large, black feed step motor gear back & forth several times. You should just feel the friction of the step motor and no binds in the feed system.
3. Check for thread caught in the gears and clean feed step motor sensor.
4. Replace the feed step motor if necessary.
E3
Needle
Plate Step Motor:
1. Remove the needle plate and press ‘D1S’. If you don’t get the error, replace the needle plate unit.
2. If you still get the error, replace the Needle Plate Step Motor Unit.
E4
1. Remove the needle plate and press ‘D1S’. If you don’t get the error, replace the needle plate unit.
2. If you still get the error, replace the Needle Plate Step Motor Unit.
E4
Thread
Cutter Motor:
1. Check the connections.
2. Check & clean the gears.
3. Check the position of the microswitch and adjust if necessary.
4. If you still get the error, replace the thread cutter motor.
E5
1. Check the connections.
2. Check & clean the gears.
3. Check the position of the microswitch and adjust if necessary.
4. If you still get the error, replace the thread cutter motor.
E5
Could
Not Detect Zigzag Phase.
1. The lower shaft shield plate set screw may be loose. Adjust the position of set plate making sure the set plate ‘blades’ are as close to each of the sensors as possible then tighten the screw.
2. Clean the lower shaft sensor.
3. Replace lower shaft sensor.
E6
1. The lower shaft shield plate set screw may be loose. Adjust the position of set plate making sure the set plate ‘blades’ are as close to each of the sensors as possible then tighten the screw.
2. Clean the lower shaft sensor.
3. Replace lower shaft sensor.
E6
Could
Not Detect Feed Phase.
1. The lower shaft shield plate set screw may be loose. Adjust the position of set plate making sure the set plate ‘blades’ are as close to each of the sensors as possible then tighten the screw.
2. Clean the lower shaft sensor.
3. Replace lower shaft sensor.
1. The lower shaft shield plate set screw may be loose. Adjust the position of set plate making sure the set plate ‘blades’ are as close to each of the sensors as possible then tighten the screw.
2. Clean the lower shaft sensor.
3. Replace lower shaft sensor.
E7
The
customer pressed the thread cutter button too many times. The thread cutter can
only be used up to 3 times in a row. Once the machine sews several stitches,
the button can then
be used.
Stop for Safety Purposes
1. Replace the foot controller first.
2. Check the connections.
3. The machine may be jammed. Remove the timing belt to locate whether the bind is on the upper shaft or lower shaft. If it is the upper, there may be thread caught in the take-up lever or crank pin. If the lower shaft is binding, check hook clearance & hook backlash. If you continue to have the problem, loosen the screws that hold the metal, lower shaft supporter. While the machine is
running slow-to-medium speed, tighten the screws.
4. Check the lower shaft sensor. Make sure the shield plate is going perfectly thru the middle of the sensor. Replace the sensor and/or shield plate if damaged.
5. Clean the sensor on the DC motor and check if the shield plate on the motor is not loose or hitting the sensor. If either the sensor or shield plate is damaged, replace the motor.
be used.
Stop for Safety Purposes
1. Replace the foot controller first.
2. Check the connections.
3. The machine may be jammed. Remove the timing belt to locate whether the bind is on the upper shaft or lower shaft. If it is the upper, there may be thread caught in the take-up lever or crank pin. If the lower shaft is binding, check hook clearance & hook backlash. If you continue to have the problem, loosen the screws that hold the metal, lower shaft supporter. While the machine is
running slow-to-medium speed, tighten the screws.
4. Check the lower shaft sensor. Make sure the shield plate is going perfectly thru the middle of the sensor. Replace the sensor and/or shield plate if damaged.
5. Clean the sensor on the DC motor and check if the shield plate on the motor is not loose or hitting the sensor. If either the sensor or shield plate is damaged, replace the motor.
