WHIRPOOL WASHING MACHINE ERROR CODES – ELECTRIC DRYER ERROR CODES

Whirpool Washing machine error codes – Electric Dryer error codes

Whirpool Error codes - Washing  machine error codes – Electric Dryer error codes Whirpool Error codes

ERROR CODES CAUSES AND SOLUTION – 4 DIGIT

F1-E0

CAUSES

EEPROM Communication Error

SOLUTIONS

Disconnect power for at least 30 seconds and then reconnect. Allow at least a minute after power has been restored and if error code reappears, replace control board .

F1-E1

CAUSES

EEPROM Checksum Error

SOLUTIONS

Disconnect power for at least 30 seconds and then reconnect. Allow at least a minute after power has been restored and if error code reappears, replace control board .

F1-E2

CAUSES

UL A/D Error(s)

SOLUTIONS

Disconnect power for at least 30 seconds and then reconnect. Allow at least a minute after power has been restored and if error code reappears, replace control board .

F1-E4

CAUSES

Model ID Error

SOLUTIONS

Disconnect power for at least 30 seconds and then reconnect. Allow at least a minute after power has been restored and if error code reappears, replace control board .

F1-E5

CAUSES

Calibration Shifted

SOLUTIONS

Disconnect power for at least 30 seconds and then reconnect. Allow at least a minute after power has been restored and if error code reappears, replace control board .

F1-E6

CAUSES

Latch Signal Mismatch Error

SOLUTIONS

Disconnect power for at least 30 seconds and then reconnect. Allow at least a minute after power has been restored and if error code reappears, replace control board .

F1-E9

CAUSES

Stack Overflow

SOLUTIONS

Disconnect power for at least 30 seconds and then reconnect. Allow at least a minute after power has been restored and if error code reappears, replace control board .

F1-E3

CAUSES

Wiring Harness Cavity Size Does Not Match Stored Value

SOLUTIONS

Check the jumpers in the harness to make sure they agree with the actual oven size.

F2-E0

CAUSES

Shorted Touch Pad (Keypad)

SOLUTIONS

Check the connection between the touch pad (keypad) and control board  to make sure it is secure. Select the 'cancel' function and wait 60 seconds. If error code reappears then replace the touch pad, or touch pad and control board  if all one assembly.

F2-E1

CAUSES

Touch Pad (Keypad) Cable Unplugged

SOLUTIONS

Check the connection between the touch pad (keypad) and control board  to make sure it is secure. Select the 'cancel' function and wait 60 seconds. If error code reappears then replace the touch pad, or touch pad and control board  if all one assembly.

F2-E5

CAUSES

Cancel Key Line Open

SOLUTIONS

Check the connection between the touch pad (keypad) and control board  to make sure it is secure. Select the 'cancel' function and wait 60 seconds. If error code reappears then replace the touch pad, or touch pad and control board  if all one assembly.

F2-E6

CAUSES

Cancel Key Line Open

SOLUTIONS

Check the connection between the touch pad (keypad) and control board  to make sure it is secure. Select the 'cancel' function and wait 60 seconds. If error code reappears then replace the touch pad, or touch pad and control board  if all one assembly.

All Error codesF3-E 

CAUSES

Oven Temperature Sensor (RTD) or Warming Drawer Defect

SOLUTIONS

Replace oven temperature sensor (RTD).

F4-E1

CAUSES

Meat Probe Defect

SOLUTIONS

This error indicates a problem with either the probe, receptacle, or probe circuit. Check the probe for pinched wires and make sure there is no condensation or contamination on receptacle. If ok, replace probe.

All Error F5-E 

CAUSES

Door Switch Defect

SOLUTIONS

This occurs when the door switches do not match. If door is latched, disconnect power from unit and check wires and connections. If damage is found, replace appropriate part. If connections are not damaged, reconnect power and hold down any key until the F5 error clears. Once the F2 code appears, select 'cancel' and observe for one minute for errors. If door is NOT latched, disconnect power from unit and check wires and connections. If damage is found, replace appropriate part. If connections are not damaged, measure door switch (door open = latch open) and latch switch (unlatch = switch open) and replace either if defective. If corrections are made during any step, power should be reconnected and the unit should be tested. Press and hold any key to clear the error code and F2 code should appear. Select 'cancel' and observe for one minute for errors. If error continues, disconnect power and replace control.

F6-E0

CAUSES

Return Line Not Connected

SOLUTIONS

This error should appear within 60 seconds after power up to appliance. Replace control board .

F7-E1

CAUSES

Common Switch Wire Is Defective

SOLUTIONS

This error occurs when common wire to latch switch and door switch is shorted. Check all connections at control board and at the latch switch and door switch. If connections are ok, then check individual switches as outlined for the F5 error code. Note: Double ovens will have two of each switch and one common wire.

ERROR CODE CAUSES AND SOLUTION - 2 DIGIT

F0

CAUSES

Control Board Failure

SOLUTIONS

Replace control board .

F1

CAUSES

Control Board Failure

SOLUTIONS

Replace control board .

F2

CAUSES

Oven Temperature Is Too High

SOLUTIONS

Check for welded contacts on bake and broil relays. If present, replace control board . For SELF CLEAN models, check door lock operation. Check sensor, sensor harness, and the sensor harness connection at sensor and oven control. Also check for any causes of high resistance in the oven temperature sensor circuit. Remember: The oven control board measures resistance of sensor circuit, not actual oven temperature.

F3

CAUSES

Open Oven Temperature Sensor (RTD)

SOLUTIONS

Replace oven temperature sensor (RTD).

F4

CAUSES

Shorted Oven Temperature Sensor (RTD)

SOLUTIONS

Replace oven temperature sensor (RTD).

F5

CAUSES

Control Board Failure

SOLUTIONS

Replace control board .

F7

CAUSES

Function Key Stuck

SOLUTIONS

Replace control board .

F8

CAUSES

Control Board Failure

SOLUTIONS

Replace control board .

F9

CAUSES

Oven Door Lock Failure

SOLUTIONS

Check door lock switches and wiring. Check for stuck lock switch.

Whirpool Duet Front Loading Automatic Washer Fault Codes

FH

CAUSES

Detects No Water Entering Machine or No Pressure Switch Trip

SOLUTIONS

Select 'cancel' twice to clear this code. If there is NO water in the unit, make sure the valves are turned on all the way. Check for plugged or kinked inlet hoses, as well as plugged screens in the inlet valves. Verify that the inlet valve is operational. If there is water in the unit, verify the drain pump is working and the pressure switch hose is in good condition and properly connected. Make sure there is not a siphon problem and check all hoses for possible leaks. Unplug the unit and disconnect the power to check all wire harness connections to the inlet valve, pressure switch, drain pump, flow meter, and Central Control Unit (CCU). Reconnect the unit and power to verify the pressure switch is operational, as well as the flow meter (blow air through the flow meter and measure resistance). Check CCU is also operational by performing a diagnostic test or any cycle. Replace failed component.

F02

CAUSES

Long Drain (Drain Exceeds 8 Minutes)

SOLUTIONS

Select 'cancel' twice to clear error code. Note: You may see a "SUD" error code appear first during this failure. This should change to the F02 error code after a few minutes. Proceed by checking the drain hoses for proper connection and kinks. Unplug unit and disconnect power. Check the electrical connections at the pump and make sure it is operational with no debris or blockage. Reconnect power and plug unit in. If problem has not been corrected, replace the pump.

F05

CAUSES

Water Temperature Sensor Error

SOLUTIONS

Unplug and disconnect power to the unit and check all connections to the water temperature sensor, heating element and element relay. Also check all components for defects. Replace failed component.

F06

CAUSES

Drive Motor Tachometer Error (Unable to Detect Motor Speed)

SOLUTIONS

Disconnect power and unplug unit. Check wire harness connections between drive motor and Motor Control Unit (MCU), and between MCU and the Central Control Unit (CCU). Reconnect power and plug unit in. Check the MCU by looking for operations of the drive motor, and check drive motor for powered rotations. Replace failed component. Note: If this failure occurs during high-speed spin, the door will be unlocked after three minutes.

F09

CAUSES

Overflow Condition (Pressure Switch Closed Too Long)

SOLUTIONS

Check to make sure drain hose is not plugged or kinked and unplug the unit and disconnect power. Check wire harness connections to pressure switch, drain pump, and Central Control Unit (CCU). Check for drain pump failure and clean it of any debris. Check the inlet valve and pressure switch for proper shut off and operation. Replace failed component. Note: If this error occurs, the door will remain locked and the drain pump will run constantly even if 'cancel' is selected. Turn off hot and cold water to faucets and unplug the unit before proceeding.

F10

CAUSES

Motor Control Unit (MCU) Heat Kink Thermal Trip (Too Hot)

SOLUTIONS

Check for proper installation and ventilation, and make sure unit is not located near a heat source. Disconnect power and unplug the unit to check wire harness connections to the motor, MCU, and Central Control Unit (CCU). Check the drive system for any worn or failed components and reconnect power and plug unit in. Check MCU by looking for operations of the drive motor and check drive motor for powered rotations. Replace failed component.

F11

CAUSES

Serial Communication Error Between MCU and CCU

SOLUTIONS

Disconnect power and unplug unit. Check wire harness connections to the motor, Motor Control Unit (MCU), and Central Control Unit (CCU). Check the drive system for any worm or failed components and reconnect power and plug unit in. Verify CCU is working by performing diagnostic test or any cycle. Check MCU by looking for operations of the drive motor and check drive motor for powered rotations. Also check the motor and wire harness. Replace defective part.

F13

CAUSES

Dispenser Circuit Error

SOLUTIONS

Disconnect power and unplug unit to check mechanical linkage from dispenser motor to top of dispenser. Check wire harness connections to the Central Control Unit (CCU) and the dispenser motor. Check dispenser motor for powered rotations. Replace failed component.

F14

CAUSES

EEPROM Error

SOLUTIONS

Disconnect power and unplug unit. Verify Central Control Unit (CCU) is operating properly by running a diagnostic test or any cycle. Replace is defective. Note: A power glitch may cause this error. Try unplugging unit for two minutes to see if that fixes error.

F15

CAUSES

Motor Control Unit (MCU) Error

SOLUTIONS

Disconnect power and unplug unit to check wire harness connections to the motor, MCU, and Central Control Unit (CCU). Check the drive belt and reconnect power and plug unit in. Check the MCU by looking for operations of the drive motor and check the drive motor for powered rotations. Replace failed component.

FdU

CAUSES

Door Unlock Error

SOLUTIONS

It is possible the door lock mechanism is broken or the door switch/lock unit has failed. Check the door switch/lock for any debris or foreign objects. Disconnect power and unplug unit to check wire harness connections to the Central Control Unit (CCU) and the door switch/lock unit. Note: Unit will attempt to unlock itself during this error six times before displaying this error code. To manually unlock the unit, unplug the power cord from the outlet and remove the toe panel. Reach up along the inside of the front panel and locate the bottom of the door latch assembly, where there should be a tear-drop shaped tab. Gently pull the tab down approximately 1/4 inch or until a 'click' is heard. The door should now be unlocked.

FdL

CAUSES

Door Lock Error

SOLUTIONS

It is possible the door lock mechanism is broken or removed, or the door switch/lock unit has failed. Disconnect power and unplug unit to check door switch/lock unit. Check the wire harness connections to the Central Control Unit (CCU) and the door switch/lock unit. Note: Unit will attempt to lock itself during this error six times before displaying the error code.

SUD

CAUSES

Suds Lock (Too Much Detergent Detected)

SOLUTIONS

Make sure drain hose is not plugged or kinked and disconnect power and unplug unit. Check wire harness connections to pressure switch, drain pump, and Central Control Unit (CCU). Make sure the drain pump is free from debris or foreign objects and then reconnect power and plug unit in. Check drain pump and pressure switch and verify CCU operation by running a diagnostic test or any cycle. Note: This error may signify a bad pump, an extra heavy load, excessive detergent, or excessive suds. If too much detergent was used, run the unit through a Rinse/Spin cycle, and then run a Normal cycle without adding detergent.

Whirpool Duet Front Loading Gas and Electric Dryer Error codes

PF

CAUSES

Power Failure

SOLUTIONS

PF error code indicates a power failure during the dryer's cycle. Press and HOLD start to continue the cycle, or press off/pause to clear display.

E1

CAUSES

Open Thermistor

SOLUTIONS

Replace thermistor.

E2

CAUSES

Shorted Thermistor

SOLUTIONS

Replace thermistor.

Whirpool Calypso Automatic Washer Error codes

PF

CAUSES

Power Failure

SOLUTIONS

PF error code indicates a power failure during the dryer's cycle. Press and HOLD start to continue the cycle, or press 'Stop/Cancel' to clear display and cancel cycle.

FL

CAUSES

Flood Condition

SOLUTIONS

FL error code will appear when the unit detects an overfill, or excessive amounts of water in tub. When this error occurs, the pump should be cycled in drain mode for 30 seconds on and 30 seconds off until the switch resets. Press 'Stop/Cancel' to clear display.

Er

CAUSES

Processor Reset Error

SOLUTIONS

This error will only occur if the unit fails to save cycle information during a power outage. Press 'Stop/Cancel' to clear display.

LF

CAUSES

Long Fill

SOLUTIONS

If the water fill time exceeds ten minutes, the water valves will be shut off and this error code will display. Press 'Stop/Cancel' to clear display.

CE

CAUSES

Communication Error

SOLUTIONS

Disconnect power and unplug unit. Check for conformal coating on serial communication pins between the machine controller and the motor controller. Make sure the harness does not have a faulty connection by checking the resistance values between serial communication pins with the connectors in place.

Ld

CAUSES

Long Drain

SOLUTIONS

This error code will appear if unit takes longer than 5 minutes to pump out water to the point where the pressure switch resets. Press 'Stop/Cancel' to clear display.

CA / CI

CAUSES

Average Current Limit / Instantaneous Current Limit

SOLUTIONS

This error code may signify a problem with the drive motor, thermal protector, or motor controller. Overloading the unit may also cause this problem.

ob

CAUSES

Off Balance

SOLUTIONS

The lid switch must be opened at least once before reseting the cycle. Opening the lid will allow you to redistribute the load to avoid a further off balance error. Press 'Stop/Cancel' to clear display.

Sr

CAUSES

Stuck Relay

SOLUTIONS

The machine control board may have a bad relay and may need to be replaced. Check pins 1 and 5 of P16 of the machine controller and pins 1 and 2 of P1 of the motor controller. This should have AC line voltage when the motor controller is powered. Press 'Stop/Cancel' to clear display.

LS

CAUSES

Lid Switch Error

SOLUTIONS

This error will occur if unit cannot detect the lid switch opening or closing. It is also possible this error code will appear is there is a disagreement between the motor and machine controllers. Open the lid or press 'Stop/Cancel' to clear display.

Flashing Display Time

CAUSES

Open Lid

SOLUTIONS

This will only occur if the lid is opened during a running cycle. Close the lid and press 'Start' to continue.

SL

CAUSES

Suds Lock

SOLUTIONS

This error will occur if the unit detects suds but is unable to clean them out. The unit will attempt the clean out the suds three times before displaying this error. It can also indicate a bad pump, an extra heavy load, excessive detergent, or excessive suds. Press 'Stop/Cancel' to clear the display.

Whirlpool Duet washing machine error codes are seen on the digital display as: F# and E# OR just as F#.
The “F” error code indicates the washing machine system or “Fault”.
Ehe “E” error is indicating the part in your washer that causing the issue or “Error”.
As a general rule, these “F” error codes mean the following…
– Whirlpool Duet Washing Machine F1 error code indicates main control board and/or program faults.
– Whirlpool Duet Washing Machine F2 error code indicates main control board and/or program faults.
– Whirlpool Duet Washing Machine F3 error code indicates washing machine sensor related issues.
– Whirlpool Duet Washing Machine F5 error code indicates door lock and door switch issues.
– Whirlpool Duet Washing Machine F6 error code indicates main control board and/or program faults.
– Whirlpool Duet Washing Machine F7 error code indicates motor and motor control problems.
– Whirlpool Duet Washing Machine F8 error code indicates water type issues related to flow or pressure issues.
– Whirlpool Duet Washing Machine F9 error code indicates the draining system on your washer has a problem.

Miscellaneous Whirlpool Duet Washing Machine Error Codes F# E#

Unplug the washer for 5 minutes and reconnect power once again.
Reselect the cycle and press Start.
The code SHOULD clear and RESET… if not continue reading below to find the exact error code on your Whirlpool washer.
Whirlpool Duet Washing Machine Error Code E01 **
Pump issue or dirty drain filter.
Clean drain filter and if error code still comes up then the pump should be checked to see if it has a stuck impeller or is faulty, clogged, or the wiring harness to it is damaged or loose.
Whirlpool Washing Machine Error Code F20
The f20 (or fh) error code on a Whirlpool Front Load Washer is an indication of a water supply issue. To remove the f20 error code from the display panel:
Press Pause/Cancel 2 times.
Whirlpool Washing Machine Error Code F21
The Whirlpool washer error code F21 means the washing machine has a “water draining issue”.
The drain pump itself or the drain hose is clogged and the washer is having problems draining the water.
The washer is taking too long to drain the water out of the tub.
Whirlpool Duet Washing Machine Error Code F 01
The pump driver does not activate.
One of the main relays is not working properly.
A communication error between the Central Control Unit and the EEPROM has occurred.
Whirlpool Duet Washing Machine Error Code F 02
Takes long time to drain.
Remove excess suds as the washer will not be able to drain sudsy water.
Unplug the washer and check filter in the drain pump for a blockage.
Whirlpool Duet Washing Machine Error Code F 05
Water temp sensor.
Unplug the washer and check the wire harness going to the water temperature sensor.
If the wiring checks good then replace the temperature sensor.
Whirlpool Duet Washing Machine Error Code F 06
Motor tachometer issue.
Check the wiring between the motor control board and the drive motor.
Whirlpool Duet Washing Machine Error Code F 09
Water Overflow or Overflow “Sensed”.
Drain pump runs constantly to drain the water.
Unplug the washer and if the washer is overfilled, check the water inlet valve for shut off of the water flow.
Whirlpool Duet Washing Machine Error Code F 10
Motor control board has overheated.
Unplug the washer and check the wiring connections on the motor control board.
Check the drive system for issues.
Whirlpool Duet Washing Machine Error Code F 11
Communication error = main electronic control board & motor control board.
Check connections on the main control board, motor control board & drive motor.
If no connection issue replace the motor control board OR the main control board.
Whirlpool Duet Washing Machine Error Code F 13
Dispenser circuit error issue.
The dispenser is unable to move into position.
You will hear the dispenser shifting before this code is shown.
Unplug the washer and check the linkage on the dispenser housing.
Whirlpool Duet Washing Machine Error Code F 14
Main control board EEPROM error.
Unplug the washer for 10 minutes and restore power.
See if the code clears and if it does not then replace the main electronic control board.
Whirlpool Duet Washing Machine Error Code F 15
Motor control board error.
Unplug washer.
Check wire harness connections on the motor control board.
Be sure that the drive motor connections are secure.
If no wiring connection problem then the motor control board should be replaced.
Whirlpool Duet Washing Machine Error Code Int
The cycle was paused/canceled.
The washer can take 30 minutes to stop spinning and drain,.
The washer will display this error code during this time.
To remove the code, press PAUSE or the CANCEL button 2 TIMES and the POWER BUTTON ONE TIME.
If the code is still shows then unplug the washer 5 minutes.
Whirlpool Duet Washing Machine Error Code rL
Certain items in the washing machine were detected on the Clean Washer cycle.
Remove the items from the washer and simply restart the Clean Washer cycle.
Whirlpool Duet Washing Machine Error Code SUD
Excess suds in the washing machine.
Washer cannot spin out the water with the excess suds or bubbles.
The washer will extend the rinse cycle time to remove the excess detergent SUDS.
The washer stops tumbling and puts in water for additional rinsing.
The washer pauses or STOPS to allow the bubbles in the suds to be removed.
Use HE detergent.
NOTE: The Sud error code can be from a bent drain hose.
Be sure the drain hose is not bent or blocked.
Whirlpool Duet Washing Machine Error Code dET
Detergent dispenser is not detected in the dispenser.
Be sure the dispenser is inserted properly.
Be sure the dispenser drawer is completely closed.
Excess SUDS can cause drain problems.
Use HE detergent.
Whirlpool Duet Washing Machine Error Code LO FL
Low flow of water.
Check the home water supply is turned on.
Check that the cold and the hot water valves are fully open.
Make sure the water inlet hoses are not bent or blocked.
Press the PAUSE or CANCEL button 2 TIMES and the POWER button ONE TIME to clear the code.
Whirlpool Duet Washing Machine Error Code FH
Not filling with water.
Make sure that both water supply valves behind the washer are open.
Check the drain system for a siphoning pissue.
If the water inlet valve assembly is defective then replace it.
Whirlpool Duet Washing Machine Error Code F 34
Certain items in the washing machine were detected on the Clean Washer cycle.
Remove the items from the washer and simply restart the Clean Washer cycle.
Whirlpool Duet Washing Machine Error Code F5 E2
The door is not locking properly.
Check that there are no items blocking the door and it is closing completely.
Press the Pause or Cancel button twice and the Power button once to clear the code.
Whirlpool Duet Washing Machine Error Code F7 E1
This code indicates a motor speed sensing error, the motor can not achieve the correct speed for the cycle selection.
Check that: All the shipping bolts have been removed and the washer has not been overloaded.
Press the Pause or Cancel button twice and the Power button once to clear the code.
Whirlpool Duet Washing Machine Error Code F8 E1
Low flow of water.
Check the home water supply is turned on.
Check that the cold and the hot water valves are fully open.
Make sure the water inlet hoses are not bent or blocked.
Press the PAUSE or CANCEL button 2 TIMES and the POWER button ONE TIME to clear the code.
Whirlpool Duet Washing Machine Error Code F8 E2
Problem with the Dispenser System.
Be sure detergent drawer is not blocked from excess detergent.
Whirlpool Duet Washing Machine Error Code F9 E1
Drain times are longer than expected – over eight 8 minutes.
Make sure the drain hose is not bent.
Whirlpool Duet Washing Machine Error Code FdL
Door lock error code.
The washer door can’t lock.
Check the door lock for damage or loose wiring.
If no problems then replace the door lock assembly.
Whirlpool Duet Washing Machine Error Code FdU
Door unlock error code.
The washer will NOT unlock – Not open.
Check door lock assembly for damage or a loose wiring.
If no problems replace the door lock assembly.
Whirlpool Duet Washing Machine Error Code 0E1
Load detected during a clean cycle fault.
Your Duet washer has detected a load during a washer cleaning cycle.
Whirlpool Duet Washing Machine Error Code F1 E1
Main control fault.
Whirlpool Duet Washing Machine Error Code F1 E2
Motor control fault.
Whirlpool Duet Washing Machine Error Code F2 E3
Cycle fault.
Whirlpool Duet Washing Machine Error Code F3 E1
Pressure switch ore sensor fault.
Whirlpool Duet Washing Machine Error Code F3 E2
Temperature sensor fault.
Whirlpool Duet Washing Machine Error Code F5 E1
Door lock fault.
Whirlpool Duet Washing Machine Error Code F5 E2
Door lock fault.
Whirlpool Duet Washing Machine Error Code F5 E3
Door unlock fault.
Whirlpool Duet Washing Machine Error Code F6 E2
Communication fault.
Whirlpool Duet Washing Machine Error Code F6 E3
Communication fault.
Whirlpool Duet Washing Machine Error Code F7 E2
Motor or motor control board fault.
Whirlpool Duet Washing Machine Error Code F8 E0
Steam valve fault.
Whirlpool Duet Washing Machine Error Code F8 E1
Water fill fault.
Whirlpool Duet Washing Machine Error Code F8 E2
Dispenser fault.
Whirlpool Duet Washing Machine Error Code F8 E3
Overflow fault.
Whirlpool Duet Washing Machine Error Code F8 E4
Flow meter fault.
Whirlpool Duet Washing Machine Error Code F9 E1
Long drain fault