Technical description and composition of the HYUNDAI H-LEDVD22V10 TV, type of panel and applicable modules. The composition of the modules.HYUNDAI LED
Model: H-LEDVD22V10
Chassis / Version: T.MS6M181.7A
Panel: M215HW01 V.B
LED backlight: Edge LED N8HE
LED driver (backlight): SQD-605 VER3.2
PWM LED driver: SAQ8818
MOSFET LED driver: FQD19N10L
Power Supply (PSU): Adapter 12V
MainBoard: T.MS6M181.7A 11012
IC MainBoard: CPU: MST6E181VS-LF-Z1, SPI Flash: 25Q32SIP, Audio: YD1517P
Tuner: ET-9L1E-E01W
Technical Specifications H-LEDVD22V10
HYUNDAI H-LEDVD22V10
General repair guidelines for TV LCD LED
Possible malfunctions
- The HYUNDAI H-LEDVD22V10 TV does not turn on and does not show any signs of operability at all. There is no reaction to the remote control and control buttons from the front panel.
With such manifestations, a malfunction is most likely to be detected in the Adapter power module.
The external adapter 12V power supply is not always subject to repair, especially since the owner can purchase it independently. But, in some cases, it makes sense to open it and eliminate the simple typical defects inherent in converters in pulsed sources. It is necessary to verify the presence of its output voltages and, if they are completely absent, check the power switches and rectifier diodes for a probable short circuit.
In case of breakdowns of semiconductors in the secondary circuits of any converter, as a rule, it can operate in emergency short-circuit mode without output voltages, and during short circuit in the elements of the primary circuit, the main fuse and, less often, the current sensor at the source of the key are most often cut off.
Mos-Fet keys used in switching power supplies usually fail due to a malfunction of other elements that can put it out of operation in key mode or provoke an excess of the maximum current or voltage. These can be circuits supplying the PWM controller, damping or frequency-setting circuits, or elements of OOS (negative feedback) in the stabilization circuit. PWM controllers (PWM), in the absence of external damage and short circuit between the terminals, are checked by replacing with obviously good ones.
- There is no image, but there is sound and all other functions work. Sometimes when you turn on the image for a second appears and disappears.
Usually in such cases, a malfunction is detected in the backlight nodes of the LED panel. Often the cause of the malfunction is the lack of current in the LED circuit, for example, an open or short circuit, or a violation of the contact connections of the connectors.
To detect a break in the LED lines without disassembling the panel, a current source is required. It is impossible to open transitions connected in series with a simple multimeter; voltage of several tens of volts is necessary.
- The TV does not turn on, the indicator indicates standby or operating mode, or blinks.
Repair or diagnostics of the T.MS6M181.7A motherboard should begin by checking the stabilizers and power converters needed to power the chips and matrix. If necessary, update or replace the software (software). In cases of attempts to repair the MB (SSB) board, it is necessary to check the health of its elements - CPU: MST6E181VS-LF-Z1b SPI Flash: 25Q32SIP, Audio: YD1517P which may require replacement with new ones. If a BGA processor is installed, there is a possibility of a violation of the soldering of the contacts of its conclusions with the board (it is diagnosed by heating).
If there is no reception of television channels, but the TV is working properly from external devices, first of all you need to check the voltage of the tuner ET-9L1E-E01W and update the software. The pulses from the I2C bus must be controlled with an oscilloscope.
Owners and users of the HYUNDAI H-LEDVD22V10 TV should remember that self-repair without special knowledge, skills and qualifications can be fraught with negative consequences that can lead to complete non-repairability of the device!
FIRMWARE FOR SPI FLASH -----------> HYUNDAI H-LEDVD22V10, Main: T.MS6M181.7A 11012, Panel: M215HW01
The appearance of MainBoard T.MS6M181.7A is shown in the figure below:Repair of the motherboard T.MS6M181.7A, which uses the multifunctional processor MST6M181VS combined with a scaler, is advisable to start by checking the power supply of the standby mode, which is implemented using a separate linear stabilizer 3.3V. Further, in the operating mode, it is necessary to check the operability of linear stabilizers or voltage converters necessary to provide power to the processor nodes: 1.2V, 2.5V, 3.3V. A voltage of 2.5V is required to power the DDR W9425G6JH memory. If there is a backlight and no image, the power of the LCD panel 5V or 12V, depending on the type of panel used, it is advisable to measure directly on the LVDS connector. If the TV does not exit Stand-by, does not respond to the remote control and control buttons, update the SPI FLASH software.
T.MS6M181.7A can be used in TVs:
AKAI LEA-19V07P (Panel M185B3-LC1), AKAI LEA-22V07P (Panel M215HGE-L10 Rev.C1), ERISSON 22LEE01 (Panel CLAA215FA04), FUSION FLTV-D22H11 (Panel LQ215M1LGN2), HYUNDAI H-LED19V13 (Panel CX185LEDM ), HYUNDAI H-LED15V7 (Panel N156B6-L0B Rev. C1 / Rev. C2), HYUNDAI H-LEDVD24V10 (Panel M236H3-LA2), RUBIN RB-19S2U (Panel HT185WX1-100), RUBIN RB-22S2UF (Panel LE2360A-V02), RUBIN RB-22S2UFD (Panel 22 "), RUBIN RB-24S2UFD (Panel V236H1-P01).
Main features of the HYUNDAI H-LEDVD22V10 device:
Installed matrix (LED panel) M215HW01 V.B.
To power the backlight LEDs, the SQD-605 LED driver is used, controlled by the SAQ8818 PWM controller. As the power elements of the LED driver, keys of the type FQD19N10L are used.
To power all the internal components of the HYUNDAI H-LEDVD22V10 TV, an external adapter 12V type source is used.
MainBoard - the main board (motherboard) is a module T.MS6M181.7A, using CPU chips: MST6E181VS-LF-Z1, SPI Flash: 25Q32SIP, Audio: YD1517P and others.
The ET-9L1E-E01W tuner provides television reception and channel tuning.
Additional technical information about the panel:
Brand: AUO
Model: M215HW01 VB
Type: a-Si TFT-LCD, Panel
Diagonal size: 21.5 inch
Resolution: 1920x1080, FHD
Display Mode: TN, Normally White, Transmissive
Active Area: 476.64x268.11 mm
Surface: Antiglare, Hard coating (3H)
Brightness: 250 cd / m²
Contrast Ratio: 1000: 1
Display Colors: 16.7M (6-bit + Hi-FRC), CIE1931 68%
Response Time: 3.8 / 1.2 (Tr / Td)
Frequency: 60Hz
Lamp Type: 16S4P WLED Without Driver
Signal Interface: LVDS (2 ch, 8-bit), 30 pins
Voltage: 5.0V
HYUNDAI H-LEDVD22V10 TV with M215HW01 LCD display, diagonal size 22 "(56 cm) in 16: 9 format. The required screen brightness of 250 cd / m² is provided by LED backlighting. Contrast, as the ratio of maximum brightness to minimum, is 1000: 1. The LED panel of this TV has an end LED backlight - Edge LED.The TV design and technical features include viewing programs and movies in high quality HD at a resolution of 1920x1080 pixels in a graphic resolution of 1080p (Full HD) standard. frequency or video signal can be processed in analogue systems PAL, SECAM, NTSC. Graphic processing and digital signal generation occurs in standards 480i, 480p, 576i, 576p, 720p, 1080i, 1080p. Supported media file formats: MP3, WMA, MPEG4, DivX , VideoCD, SVCD, Picture CD, JPEG.
The power of the acoustic system of sound 6 W (2x3 W) provide two speakers. The audio processing system NICAM STEREO is used.
The external interface (communication with other devices) is supported by standard input and output connectors: antenna input (RF), AV, audio x2, component, SCART, RGB, VGA, HDMI, USB. An output for connecting headphones is provided. To connect a computer or laptop to this TV model, a VGA (D-Sub 15) connector is used on the TV case, this interface supports resolutions: 640x480, 800x600, 1024x768, 1360x768.
Overall dimensions: 529x322x155 mm.
Mass of the TV: 4.6 kg.
Attention! The panel of the M215HW01 V.B of the HYUNDAI H-LEDVD22V10 LED TV is an expensive and unreliable element.
Avoid any impact on the glass and pressure on the surface of the screen to avoid damage to the LED panel!
It is also unsafe to get liquid on the screen. Sometimes one drop is enough if it flows down the glass onto the cables so that the TV becomes unrepairable.
