MYSTERY LED
Model: MTV-4030LT2
Panel: V400HJ6-PE1
LED backlight: LED40D12-ZC14-04 (A) p-n 30340012203
LED driver (backlight): integrated into PSU
PWM LED driver: OB3368AP
Power Supply (PSU): TV3902-ZC02-01 (D)
PWM Power: OB5269CP
MainBoard: MSDV3222-ZC01-01 MSAV3220-ZC26-02 (B), pn 303C3220156
IC MainBoard: CPU: MSD308BT-SW, SPI Flash: GD25Q64B, EEPROM T-con 24C16, Scaler: NT71263FG-300; DRAM: H5TQ1G63DFR
Tuner: LHD
Control: IR: TV3023-ZC10-01 (C) p / n 303CMG30234
Technical Specifications MTV-4030LT2
MYSTERY MTV-4030LT2
General repair guidelines for TV LCD LED
Possible manifestations of defects
- The MYSTERY MTV-4030LT2 TV does not turn on, does not respond to the remote control and buttons on the control panel, the indicators do not light or flash.
In the vast majority of such cases, a malfunction is detected in the TV3902-ZC02-01 power supply module. Then we recommend that you measure its output voltages and, if they are absent, you should check the health of the power switches and rectifier diodes of the converters for a probable short circuit.
In the event of a breakdown in the secondary circuits of the converter, it can usually fail in short circuit mode, and in the event of a short circuit in the power elements of the primary circuit, the main fuse or current sensor at the source of the key most often breaks.
Mos-Fet keys used in switching power supplies usually fail due to a malfunction of other elements that can put it out of operation in key mode or provoke an excess of the maximum current or voltage. It can be supply, damper circuits, or elements of OOS (negative feedback) stabilization. The reason for the breakdown of the power key may be PWM (PWM) OB5269CP. It is checked only by replacement with a known good one.
- There is no image, but there is sound and reaction to the remote control. Or for a second, the image may appear immediately after switching on.
In most cases, the malfunction is caused by the lack of a backlight display. The reason for this may be a break in the LED circuit, or a problem in stabilizing their power supply.
It is impossible to check the LED line for breaks without disassembling the panel with a multimeter or tester. For these purposes, it is necessary to open all series-connected PN junctions and a voltage of the order of tens of volts will be required, and ideally, a current source. Having disassembled the panel, it is necessary to check each LED separately. Chinese multimeters, as a rule, light up a single 3-volt LED in the forward direction. In the case of using dual 6-volt LEDs, the PN junction of its protective zener diode can serve as a health indicator. In faulty LEDs, the zener diode will either be cut off or broken into short-circuit.
- The TV does not turn on, does not respond to the remote control. The indicator blinks or signals standby mode.
Repair or diagnostics of the motherboard MSDV3222-ZC01-01 should begin by checking the stabilizers and power converters needed to power the chips and matrix. If necessary, update or replace the software (software). Sophisticated MB board repair (SSB) is in some cases possible and practiced by repairmen. To do this, check and, if necessary, replace the CPU elements: MSD308BT-SW, SPI Flash: GD25Q64B, EEPROM T-con 24C16, Scaller: NT71263FG-300; DRAM: H5TQ1G63DFR. BGA chip malfunctions are usually easy to detect by warming up.
Before changing the LHD tuner, if it is not possible to tune to television channels, make sure that there are supply voltages, which must be measured at the corresponding terminals of the tuner and check the software for correctness. The pulses of the data exchange of the tuner with the processor can be controlled by an oscilloscope
It should be remembered! Attempts to independently repair the MYSTERY MTV-4030LT2 TV, in the absence of the necessary qualifications and experience, are categorically not recommended and are fraught with negative consequences, up to the complete non-repairability of the device!
FIRMWARE FOR SPI FLASH -----------> MYSTERY MTV-4030LT2 V1N11, Main: MSDV3222-ZC01-01, Panel: V400HJ6-PE1
SCHEMATIC DIAGRAM / SERVICE MANUAL ------------------> MYSTERY MTV-3224LT2 Chassis MSDV3222-ZC01-01 (MSDV3222-YL01-01)
Repair MainBoardTo reduce the backlight current in LED drivers with the OB3368AP controller, the total resistance of the resistors from the 17 ISET pin to the housing should be proportionally increased. The current in milliamperes in each channel is determined from the calculation of 4000 * 1.2 / Rset, where Rset is the resistance from the output of 17 ISET to the housing in kilo-ohms.
The appearance of the MainBoard MSDV3222-ZC01-01 is shown in the figure below:
The motherboard MSDV3222-ZC01-01 is made on a single chassis with a power module and an inverter to power the LED panel. The MSD308BT-SW multi-function control processor with built-in scaler is used. Repair of the power module is carried out according to standard technology - verification of power cells, electrolytic capacitors and secondary supply voltages. The following is a functional check of stabilizers and converters for powering the internal nodes of the processor and LCD panel. It should be borne in mind that if there are problems with the software in the SPI Flash chips manufactured by WINBOND, it is advisable to replace the chip itself along with the contents of the software.MSDV3222-ZC01-01 can be used in TVs:
BBK LEM3284DT2 (Panel LSC320AN02), MYSTERY MTV-2229LT2 (Panel M215HTN01.1 ), MYSTERY MTV-2429LT2 (Panel M240HTN01.2), MYSTERY MTV-2223LT2 (Panel LC215DTBA), MYSTERY MTV-2431LT2 (Panel V236BJ1 600), MYSTERY MTV-1924LT2 (Panel HT185WXF-100), MYSTERY MTV-3228LT2 (Panel LK315T3HB94), MYSTERY MTV-3023LT2 (Panel MT3151A05), MYSTERY MTV-2228LT2 (Panel RUNTK0001ZDP2), MYSTERY MTV-1929LT2 (Panel V185BJ1-PE1), MYSTERY MTV-3223LT2 (Panel LC315TU3A), MYSTERY MTV-3224LT2 (Panel HV320WX2-20A), MYSTERY MTV-3028LT2 (Panel ST2751A01-3), MYSTERY MTV-2428LT2 (Panel V236BJ1-P01), MYSTERY MTV-2424LT2 (Panel HM236WU8-200 ), MYSTERY MTV-4030LT2 (Panel V400HJ6-PE1), MYSTERY MTV-3031LT2 (Panel V290BJ1-PE1), MYSTERY MTV-3226LT2 (Panel V320BJ7-PE1).
The appearance of the power supply
Main features of the MYSTERY MTV-4030LT2 device:
Installed matrix (LED-panel) V400HJ6-PE1.
To power the backlight LEDs, a converter is used, combined with a power supply, controlled by the OB3368AP PWM controller.
The necessary supply voltages for all nodes of the MYSTERY MTV-4030LT2 television are generated by the TV3902-ZC02-01 power supply module or its analogs using OB5269CP microcircuits.
MainBoard - the main board (motherboard) is an MSDV3222-ZC01-01 module, using CPU chips: MSD308BT-SW, SPI Flash: GD25Q64B, EEPROM T-con 24C16, Scaller: NT71263FG-300; DRAM: H5TQ1G63DFR and others.
The LHD tuner provides television reception and channel tuning.
Additional technical information about the panel:
Brand: INNOLUX
Model: V400HJ6-PE1 Rev. C2
Type: a-Si TFT-LCD, CELL
Diagonal size: 40 inch
Resolution: 1920x1080, FHD
Display Mode: MVA, Normally Black, Transmissive
Active Area: 878.112x485.352 mm
Surface: Antiglare (Haze 1%)
Glass Depth: 0.50 + 0.50 mm
Transmissivity: 6.0% (with Polarizer)
Contrast Ratio: 5000: 1
Display Colors: 16.7M (8-bit)
Response Time: 8.5 (G to G)
Frequency: 60Hz
Signal Interface: LVDS (2 ch, 8-bit), 51 pins
Voltage: 12.0V
MYSTERY MTV-4030LT2 TV with V400HJ6-PE1 LCD, 40 "(102 cm) diagonal, 16: 9 format. The required screen brightness of 300 cd / m² is provided by LED backlighting. Contrast, as the ratio of maximum brightness to minimum, is 2000: 1. The LED-panel of this TV has end-face LED illumination - Edge LED.The design and technical capabilities of the TV include watching programs and movies in high quality HD at a resolution of 1920x1080 pixels in a graphic resolution according to the standard 1080p (Full HD). frequency or video signal can be processed in analog systems PAL, SECAM, NTSC. Graphic processing and digital signal generation occurs in standards 480i, 480p, 576i, 576p, 720p, 1080i, 1080p. Supported media file formats: MP3, WMA, MPEG4, MKV , JPEG.
The power of the sound system 16 W (2x8 W) provide two speakers. It uses a NICAM stereo signal processing system and Sound Surround.
The external interface (communication with other devices) is supported by standard input and output connectors: antenna input (RF), AV, audio x2, component, VGA, HDMI x2, USB. An output for connecting headphones is provided. To connect a computer or laptop to this TV model, a VGA (D-Sub 15) connector is used on the TV case, this interface supports resolutions: 640x480, 800x600, 1024x768, 1280x1024, 1360x768, 1920x1080.
A digital tuner is capable of receiving television channels in the DVB-T MPEG4, DVB-C, DVB-T2 standards.
Attention! The MYSTERY MTV-4030LT2 LED TV panel V400HJ6-PE1 is an expensive and unreliable element.
Avoid any impact on the glass and pressure on the surface of the screen to avoid damage to the LED panel!
It is also unsafe to get liquid on the screen.