Technical description and composition of the FUSION FLTV-19W6 TV, panel type and applicable modules. The composition of the modules.Fusion
Model: FLTV-19W6
Chassis / Version: B.SPC81B-1 9245
Panel: M190A1-P0A
T-CON: M190A1-L0A-X + C
Inverter (backlight): integrated into PSU
PWM Inverter: BIT3713
MOSFET Inverter: 4606
Power Supply (PSU): LK-PI190414CF
PWM Power: GR8876
MainBoard: CV7050LA // B.SPC81B-1 9245
IC MainBoard: TDA1517P, TDA9886TS
Tuner: F21WT-3BAR-E // ET-6T1E-LF-108W-A
Technical Specifications FLTV-19W6
FUSION FLTV-19W6
General recommendations for repairing TV LCD
FUSION troubleshooting and repair with B.SPC81B-1 9245 chassis, as well as other electronic devices, is recommended to start with an external examination of the external and internal elements. Often, by the external signs and nature of the damage to the elements, it becomes possible to draw some conclusions and determine a further algorithm for finding a defect before making the necessary measurements at control points. Swollen electrolytic or cermet capacitors, charred resistors, ring cracks in the soldered terminals of the elements - all this can significantly help the master to determine the causes and consequences of the malfunction of the TV.
If the FUSION FLTV-19W6 does not turn on, no control lights on the front panel light up or blink, therefore, there is a very high probability of a power module malfunction. In some cases, only the processor power regulator may be faulty. When diagnosing and repairing the power supply, first of all, replace the swollen filter capacitors of the secondary rectifiers and check the fuse and, if it is broken, it is necessary to identify the cause. Often in such cases, an avalanche (thermal) breakdown is detected in the power semiconductor elements of the module — rectifier diodes and transistors in the primary circuit.
As a rule, the keys in switching power supplies (SMPS) are reliable enough and rarely fail for no reason to be looked for by checking other components of the circuit - electrolytic capacitors, resistors and semiconductor elements of the primary circuit. The PWM chip is verified by replacing it with a known good one.
If the FUSION FLTV-19W6 TV does not have an image, but there is sound, the malfunction should be sought in the power converter of the backlight (inverter). It is also necessary to check the serviceability of the electrolytic capacitors of the filter of the secondary rectifiers of the PSU (power supply) for an overstated ESR. It is necessary to take into account that in cases of inverter protection shutdown (in order to be able to diagnose) there is a risk of failure of the inverter power elements and take special care. After carrying out repairs, the protection circuit must be restored for further safe operation of the TV.
On the B.SPC81B-1 9245 motherboard, in case of a malfunction, you should first check the performance of all the stabilizers or power converters of the microcircuits and, if necessary, update the software (software). When repairing an MB board, you need to check its components TDA1517P, TDA9886TS. Defective items should be replaced. If BGA chips are installed, their malfunction is usually localized by heating. If chips with BGA soldering technology are used, a problem in its implementation is detected by the local heating of the chip.
Once again, remind users! Attempts to independently repair the FUSION FLTV-19W6 TV without the appropriate qualifications and experience can lead to its complete non-repairability!
FIRMWARE FOR SPI FLASH -----------> FUSION FLTV-19W6, Main: B.SPC81B-1 9245, Panel: M190A1-P0A
The appearance of the MainBoard CV7050LA is shown in the figure below:CV7050LA
CV7050LA can be used in TVs:
BBK LT1902S (Panel M190A1-P0A), BBK LT2202S (Panel M216H1-P01), BBK LT2428HD (Panel V236H1-P01 HK236WLCM-CH03H), BBK LT2428S (Panel V236H1-P01), FUSION FLTV-19W6 (Panel M190A1-P0A), IZUMI TL26H615B (Panel M260TWR1).
Main features of the FUSION FLTV-19W6 device:
Installed matrix (LCD panel) M190A1-P0A.
The matrix control uses the Timing Controller (T-CON) M190A1-L0A-X + C.
To power the backlight, a converter is used, combined with a power supply, controlled by a BIT3713 PWM controller. As power elements of the inverter, keys of type 4606 are used.
The necessary supply voltages for all nodes of the FUSION FLTV-19W6 TV are generated by the LK-PI190414CF power module, or its analogs using GR8876 microcircuits.
MainBoard - the main board (motherboard) is a CV7050LA module, using TDA1517P, TDA9886TS and others.
The tuner F21WT-3BAR-E // ET-6T1E-LF-108W-A provides the reception of television programs and tuning to channels.
Additional technical information about the panel:
Brand: CHIMEI INNOLUX
Model: M190A1-P0A
Type: a-Si TFT-LCD, CELL
Diagonal size: 19.0 inch
Resolution: 1440x900, WXGA +
Display Mode: TN, Normally White, Transmissive
Active Area: 408.24x255.15 mm
Surface: Antiglare (Haze 25%), Hard coating (3H)
Transmissivity: 5.6% (with Polarizer)
Contrast Ratio: 1000: 1
Display Colors: 16.7M (8-bit)
Response Time: 1.5 / 3.5 (Tr / Td)
Frequency: 60Hz
Signal Interface: LVDS (2 ch, 8-bit), 30 pins
Voltage: 5.0V
FUSION FLTV-19W6 TV with TM190MFS01 LCD, 19 "(48 cm) diagonal 16:10 format. Screen brightness of 300 cd / m² is provided by CCFL (EEFL) fluorescent lamps. 2000: 1 dynamic contrast is provided by special control of operation illumination depending on the illuminated areas in the plot. You can view images in high quality HD at a resolution of 1440x900 pixels in the standard for graphic decomposition 720p (HD Ready). The input high-frequency or video signal can be processed in analog systems PAL, SECAM, NTSC. Graphic image Digital signal processing and generation takes place in the standards 480i, 480p, 576i, 576p, 720p, 1080i.
The power of the sound system 6 W (2x3 W) provide two speakers. The audio processing system NICAM STEREO is used.
The external interface (communication with other devices) is supported by standard input and output connectors: antenna input (RF), AV, audio x2, S-Video, SCART, RGB, VGA, HDMI. An output for connecting headphones is provided. To connect a computer or laptop to this TV model, a VGA (D-Sub 15) connector is used on the TV case, this interface supports resolutions: 640x480, 800x600, 1024x768.
The power consumed by the TV working in the network mode is 60 watts.
Overall dimensions: 532x435x155 mm.
TV Weight: 5.5 kg.
Attention! The TM190MFS01 LCD panel of the FUSION FLTV-19W6 LCD TV is its most expensive component.
Avoid hitting the glass and exerting pressure on the screen to avoid permanent damage to the LCD panel!
