Technical description and composition of the FUSION FLTV-24T9 TV, panel type and applicable modules. The composition of the modules.Fusion
Model: FLTV-24T9
Chassis / Version: V5L10
Panel: M240HW01 V.B
Power Supply (PSU): Adapter 12V
MainBoard: T.VST59.62
IC MainBoard: CPU: TSUMV59XU-Z1, FLASH: CD25Q32B2, TDA-1517P, TPS54329 (PWM Step-down), BL8024 (PWM Step-down marker GG ..)
Tuner: CDT-3NP5L1-10
Technical Specifications FLTV-24T9
FUSION FLTV-24T9
General recommendations for repairing TV LCD
Repair of electronic equipment usually begins with its external inspection and diagnosis of the malfunction. In this case, you should inspect all the internal elements of the V5L10 chassis, as well as the external chassis. Specific external damage to some elements can sometimes indicate further actions to determine the malfunction of the TV and localize the defect before the necessary measurements are taken. Electrolytic capacitors of filters with a swollen casing, as well as ring cracks formed in the soldered leads of heating elements, or a layer of coal on burnt resistors sometimes tell the repairman the causes of the malfunction and possible consequences.
If the FUSION FLTV-24T9 does not turn on, no control lights on the front panel light up or blink, therefore, there is a very high probability of a power module malfunction. In some cases, only the processor power regulator may be faulty. When diagnosing and repairing the power supply, after replacing the swollen capacitors of the secondary rectifier filters (if any), you must first check the mains fuse. When it is broken, the power elements of transistors and rectifier bridge diodes should be checked for avalanche (thermal) breakdown.
It should be remembered that in the practice of repair, usually the power switches in switching power supplies (SMPS) do not fail due to their poor quality and, in such cases, it is necessary to look for the cause that led to a malfunction and provoked a breakdown of the key. Most often, the culprits of the accident are dried electrolytic capacitors or dangling resistors in the primary circuit, or the PWM controller chip itself may be faulty. It is also necessary to check all the semiconductor elements of the stabilization circuit in the primary and secondary circuits.
Sometimes the FUSION FLTV-24T9 TV does not have an image, but there is sound, or the image appears and immediately disappears. In this case, there is a high probability of a malfunction of the backlight converter or the lamps themselves, which can be checked by replacement. In such cases, it is necessary to verify the serviceability of all electrolytic capacitors of the filter according to the power supply of the inverter itself, including in the power supply unit (power supply unit). If in diagnosing a malfunction, it is necessary to disable the inverter protection, there is a risk of failure of the power elements of the inverter, and special care is required during work, and after they are finished, it is necessary to restore the protection circuits for further safe operation of the TV by the owner in normal mode.
Repair or diagnostics of the T.VST59.62 motherboard should begin by checking the stabilizers or power converters of its microcircuits. If necessary, you should update the software (software). If it is not possible to replace the MB (SSB) card, you need to check the health of its elements - CPU: TSUMV59XU-Z1, FLASH: CD25Q32B. Defective components should be replaced.
Once again, remind users! Attempts to independently repair the FUSION FLTV-24T9 TV without the appropriate qualifications and experience can lead to its complete unrepairability!
FIRMWARE FOR SPI FLASH -----------> FUSION FLT-24T9 V5L10, Main: T.VST59.62, Panel: M240HW01 V.B
In case of failures in the software of SPI FLASH microcircuits made by Winbond, they can for some time restore their working capacity after temperature exposure - heating by a hairdryer of a soldering station or even a lighter. Usually this is enough to read the regular contents of the software. In such cases, the chip must be replaced with a new one.
Repair MainBoardThe appearance of MainBoard T.VST59.62 is shown in the figure below:
T.VST59.62
It is advisable to start the repair of the T.VST59.62 motherboard based on the TSUMV59Xxx multifunction processor by checking the operability of linear voltage stabilizers or voltage converters necessary to provide power to the processor nodes - 1.2V core power, 1.8V DDR memory and Stand-by 3.3V mode . If there is no image, but the display backlight is working properly, you should check the power supply voltage of the LCD panel 5V or 12V, depending on the type of panel used.
T.VST59.62 can be used on TVs:
Akai LEA-22V21M (Panel A215ED1DA3-1), ERISSON 22LEN18 (Panel M215HGJ-L21), ERISSON 16LEN18 (Panel N156BGE-L11 Rev.C1), ERISSON 24LEN18 (Panel M236HGE-L20), Fusion FLTV-16L10B (Panel T156LL10-AW4), FUSION FLTV-24T9 (Panel M240HW01 V.B), FUSION FLTV-16T9 (Panel B156XTN02), FUSION FLTV-16T9D (Panel T156LL10-AW4), HYUNDAI H-LED19V13 (Panel CX185LEDM ), SUPRA STV-LC19811FL (Panel M185XTN01.3), SUPRA STV-LC19820WL (Panel LM185WH2), SUPRA STV-LC22820FL (Panel LS215AFTNM), SUPRA STV-LC18250WL (Panel B173HW02 V.1), SUPRA STV-LC22810FL (Panel M215HGE-L21 Rev.C1), SUPRA STV-LC16810WL (Panel B156RW01 V.1), SUPRA STV-LC18251FL (Panel N173HGE-L11 Rev. C1), SUPRA STV-LC22811FL (Panel 1080p Full HD 1920x1080), SUPRA STV-LC1982WL (Panel 1080p Full HD 1920x1080), TELEFUNKEN TF-LED22S3 (Panel M215HGE-P02).
Main features of the FUSION FLTV-24T9 device:
Installed matrix (LCD-panel) M240HW01 V.B.
To power all the internal components of the FUSION FLTV-24T9 TV, an external adapter 12V type is used.
MainBoard - the main board (motherboard) is a T.VST59.62 module, using CPU chips: TSUMV59XU-Z1, FLASH: CD25Q32B2, TDA-1517P, TPS54329 (PWM Step-down), BL8024 (PWM Step-down marker GG ..) and others.
The tuner CDT-3NP5L1-10 provides reception of television programs and tuning to channels.
Additional technical information about the panel:
Brand: AUO
Model: M240HW01 VB
Type: a-Si TFT-LCD, Panel
Diagonal size: 24.0 inch
Resolution: 1920x1080, FHD
Display Mode: TN, Normally White, Transmissive
Active Area: 531.36x298.89 mm
Surface: Antiglare, Hard coating (3H)
Brightness: 250 cd / m²
Contrast Ratio: 1000: 1
Display Colors: 16.7M (6-bit + Hi-FRC)
Response Time: 3.5 / 1.5 (Tr / Td)
Frequency: 60Hz
Lamp Type: 11S4P WLED Without Driver
Signal Interface: LVDS (2 ch, 8-bit), 30 pins
Voltage: 5.0V
FUSION FLTV-24T9 TV with an M240HW01 LCD, 24 "(61 cm) diagonal size of 16: 9 format. The required brightness of the screen is 250 cd / m² LED backlighting. Contrast, as the ratio of maximum brightness to minimum, is 1000: 1. Dynamic contrast ratio of 20,000: 1 is achieved by special control of the LEDs. The LED-panel of this TV is equipped with an end LED backlight - Edge LED. The design and technical capabilities of the TV include watching programs and movies in high quality HD at resolution of 1920x1080 pixels in graphic decomposition according to the standard 1080p (Full HD). The input high-frequency or video signal can be processed in analog systems PAL, SECAM, NTSC. Graphic processing and digital signal generation occurs in the standards 480i, 480p, 576i, 576p, 720p, 1080i , 1080p. Supported media file formats: MP3, MPEG4, JPEG.
The power of the acoustic system of sound 6 W (2x3 W) provide two speakers. The audio processing system NICAM STEREO is used.
The external interface (communication with other devices) is supported by standard input and output connectors: antenna input (RF), AV, audio x2, component, SCART, VGA, HDMI, USB. An output for connecting headphones is provided. To connect a computer or laptop to this TV model, a VGA (D-Sub 15) connector is used on the TV case, this interface supports resolutions: 640x480, 800x600, 1024x768, 1360x768.
The power consumed by the TV working in the network mode is 40 watts.
Overall dimensions: 587x439x150 mm.
TV Weight: 5 kg.
Attention! The M240HW01 V.B panel of the FUSION FLTV-24T9 LED TV is an expensive and unreliable element.
Avoid any impact on the glass and pressure on the surface of the screen to avoid damage to the LED panel!
It is also unsafe to get liquid on the screen. Sometimes one drop is enough if it flows down the glass onto the cables so that the TV becomes unrepairable.
