Technical description and composition of the MYSTERY MTV-3018LW TV, type of panel and applicable modules. The composition of the modules.MYSTERY LED
Model: MTV-3018LW
Chassis / Version: V1L11
Panel: V290BJ1-PE1
LED driver (backlight): integrated into MainBoard
PWM LED driver: AP3039AM, AP3608E
Power Supply (PSU): integrated into MainBoard
PWM Power: SG6848 (PWM SOT23-6)
MainBoard: MSTV2407-ZC01-01
IC MainBoard: CPU: MST6E182VG-LF-Z1, Flash: 25Q32BVSIG, Sound: TDA1517
Tuner: F35WT-2A-E
Control: Service Login: INPUT 2580
Technical Specifications MTV-3018LW
MYSTERY MTV-3018LW
General repair guidelines for TV LCD LED
MYSTERY MTV-3018LW, like other electronic devices, is recommended to start troubleshooting and repair with an external inspection of the external and internal elements. Sometimes, based on visible changes in the components of the device, it is possible to draw some conclusions and determine the direction of further troubleshooting even before the necessary measurements are taken. Ring cracks in the soldering of the leads of the heating elements, swollen electrolytic capacitors, a charred paint layer on the resistors - all this for the repairman can be a significant clue in the assumptions about the causes and consequences of the malfunction.
Malfunctions of the power module can be expressed in different ways, for example, the MYSTERY MTV-3018LW does not turn on at all and the control lamps on its front panel do not light up and do not blink, and there are no signs of operability. It should be noted that with the same external manifestations, the processor power regulator (converter) may be faulty. When diagnosing and repairing the power supply, first of all, replace the swollen capacitors of the filter of the secondary rectifiers and check the fuse and, if it is broken, it is necessary to identify the cause. Often in such cases, an avalanche (thermal) breakdown is detected in the power semiconductor elements of the module — rectifier diodes and transistors in the primary circuit.
In most cases, key breakdowns in switching power supplies (SMPS) do not occur for no reason and you should look for other faulty circuit elements that could provoke a defect. This can be dried electrolytic capacitors in the primary circuit, and faulty damper elements, as well as dangling resistors or punched semiconductor elements in the stabilization circuits. Possible defective PWM chip from the manufacturer.
In cases where the MYSTERY MTV-3018LW TV has lost its image, and the sound is there and all other functions are operational, there is a possibility of a malfunction of the LED driver (converter for powering the backlight LEDs of the V290BJ1-PE1 panel). When you turn on the TV, the image may appear briefly and disappear immediately. It must be borne in mind that with such manifestations the LEDs themselves also fail.
Often in the absence of backlighting, disassembling the panel is required. It is necessary to check the serviceability of the transitions of the LEDs, as well as the reliability of the contact connections in the lines and connectors.
It is impossible to check the LED line for breaks without disassembling the panel with a multimeter or tester. For these purposes, it is necessary to open all series-connected PN junctions and a voltage of the order of tens of volts will be required, and ideally, a current source.
In cases of attempts to repair the motherboard MSTV2407-ZC01-01, it is necessary to check the operability of the stabilizers or power converters of its microcircuits and, if possible, update the software (software). BGA chips can in most cases be diagnosed by local heating.
Complex repair of MB (SSB) is possible only in the conditions of a service center with the necessary equipment. Checking or replacing FLASH elements: EN25Q32 requires the necessary training and professional skills to repair modules at the component level. Problems associated with the use of BGA soldering technologies can be diagnosed by warming up.
If the TV works normally from external devices, but does not tune into television channels, the tuner F35WT-2A-E may be malfunctioning. In such cases, first of all, you should make sure that there are supply voltages at its corresponding terminals, as well as the power supply of varicaps (30-33V).
Once again, we remind TV users: you should not make attempts to repair it yourself without the appropriate knowledge, experience and the necessary qualifications! Trust the repair only to professionals with sufficient experience in the field of electronic equipment repair.
FIRMWARE FOR SPI FLASH -----------> MYSTERY MTV-3018LW (V1L11), Main MSTV2407-ZC01-01, Panel V290BJ1-PE1
SCHEMATIC DIAGRAM / SERVICE MANUAL ------------------> MYSTERY Main MSTV2407-ZC01-01
If a failure occurs in the SPI FLASH Winbond software, we recommend that you replace the chip with a new one. In addition, faulty Winbond microcircuits can sometimes recover for a while after being heated by a soldering station or even a lighter, which is enough to read its regular contents.
To reduce the backlight current in LED drivers with the AP3039AM controller and the AP3608EM terminal stage (AP3039AM-G1 & AP3608EM-G1), the AP3608EM (AP3608E) microcircuit should proportionally increase the resistor from terminal 14 (ISET) to the housing. The maximum current in each channel (in milliamperes) for the Rset resistor (in kilo-ohms) is determined from the ratio 1.194V / Rset. In channels connected in parallel, the currents add up.
Repair MainBoardThe appearance of the MainBoard MSTV2407-ZC01-01 is shown in the figure below:
MSTV2407-ZC01-01
MSTV2407-ZC01-01 motherboard is combined with a power module. The processor is MST6E182VG, or MST6E181VG, made using BGA technology. Repair of the power module is carried out according to conventional technology, starting with checking its power elements. The following is a functional check of the converters for the processor power: + 1.3V, + 1.8V, 3.3V, based on SY8008B PWM controllers. The power supply of the built-in DDR 2.5V is generated from a 3.3V source using the P-N junction of the 1N4001 diode (3.3V-0.8V = 2.5V). Standby mode is organized from the linear stabilizer series 1117-3V3. The LCD panel is powered by either 5V or 12V, depending on the type of panel used.
MSTV2407-ZC01-01 can be used in TVs:
BBK LEM2249HD Ver2 (Panel LM215DT5D), BBK LEM2284F (Panel M215HG-LE4 Rev.C3), BBK LEM2681F (Panel V260H1-LE10 Rev. C1 ), BBK LEM2682 LEM2682DT (Panel V260B2-LE11 Rev.C1), BBK LEM3284F (Panel HV320WXC-200), Haier LE32T1000 (Panel T320XVN09.0), MYSTERY MTV-2224LW (Panel M215HG-LE4 Rev.C3), MYSTERY MTV-3222LW (Panel T320XVN01.0), MYSTERY MTV-1924LW (Panel V185B1-L17), MYSTERY MTV-3018LW (Panel V290BJ1-PE1), MYSTERY MTV-1911LW (Panel HT185WX7-100), MYSTERY MTV-1922LW (Panel V185B1-L17), MYSTERY MTV-1913LW (Panel HT185WX7-100), MYSTERY MTV-3218LW (Panel HV320WX2-20A), MYSTERY MTV-1918LW (Panel V185B1-L17), MYSTERY MTV-2213LW (Panel M215HGE-L10), MYSTERY MTV-2222LW (Panel M215HG-LE4 REV.C3), MYSTERY MTV-2418LW (Panel HM236WUA-100), MYSTERY MTV-2424LW (Panel HM236WU8-100), MYSTERY MTV-1914LW (Panel V185B1-L15 Rev.c1), MYSTERY MTV-3223LW (Panel LK315T3HB94), MYSTERY MTV-2422LW (Panel HM236WU8–100), MYSTERY MTV-3224LW (Panel T320XVN09.0), MYSTERY MTV-2218LW (Panel CLAA215FA10), MYSTERY MTV-1911WL (Panel V185B1-L15 REV.C1), MYSTERY MTV-3221LW (Panel HV320WX2-268), MYSTERY MTV-2211W (Panel M215HG-LE4 ).
Main features of the MYSTERY MTV-3018LW device:
Installed matrix (LED-panel) V290BJ1-PE1.
To power the backlight LEDs, a converter is used, combined with the main board MSTV2407-ZC01-01, controlled by the AP3039AM, AP3608E PWM controller.
The power module is combined with the MainBoard and is made according to the flyback AC / DC voltage converter using SG6848 microcircuits (PWM SOT23-6).
MainBoard - the main board (motherboard) is an MSTV2407-ZC01-01 module, using CPU chips: MST6E182VG-LF-Z1, Flash: 25Q32BVSIG, Sound: TDA1517 and others.
The F35WT-2A-E tuner provides television reception and channel tuning.
Additional technical information about the panel:
Brand: CHIMEI INNOLUX
Model: V290BJ1-PE1
Type: a-Si TFT-LCD, CELL
Diagonal size: 29.0 inch
Resolution: 1366x768, WXGA
Display Mode: Super MVA, Normally Black, Transmissive
Active Area: 631.092x354.816 mm
Surface: Antiglare (Haze 1%)
Glass Depth: 0.50 + 0.50 mm
Transmissivity: 5.4% (with Polarizer)
Contrast Ratio: 3000: 1
Display Colors: 16.7M (8-bit)
Response Time: 9.5 (G to G)
Frequency: 60Hz
Signal Interface: LVDS (1 ch, 8-bit), 30 pins
Voltage: 12.0V
MYSTERY MTV-3018LW TV with V290BJ1-PE1 LCD display, 29 "(74 cm) diagonal size in 16: 9 format. The required screen brightness of 300 cd / m² is provided by LED backlighting. Contrast, as the ratio of maximum brightness to minimum, is 2000: 1. Edge LED backlighting is implemented in the LED panel of this TV - Edge LED. You can view images in high quality HD at a resolution of 1366x768 pixels in the standard of graphic decomposition 720p (HD Ready). The input high-frequency or video signal can be processed in analog systems PAL, SECAM, NTSC. Graphic processing and digital signal generation occurs in the standards 480i, 480p, 576i, 576p, 720p, 1080i. Supported media file formats: MP3, JPEG.
The power of the sound system 16 W (2x8 W) provide two speakers. The audio processing system NICAM STEREO is used.
The external interface (communication with other devices) is supported by standard input and output connectors: antenna input (RF), AV, audio x2, component, VGA, HDMI x2, USB. An output for connecting headphones is provided. To connect a computer or laptop to this TV model, a VGA (D-Sub 15) connector is used on the TV case, this interface supports resolutions: 640x480, 800x600, 1024x768, 1360x768.
The power consumed by the TV in the operating mode from the network is 40 watts.
Dimensions: With stand 642x444x209 mm, Without stand 570x345x70 mm.
Attention! The panel V290BJ1-PE1 of the MYSTERY MTV-3018LW LED TV is an expensive and unreliable element.
Avoid any impact on the glass and pressure on the surface of the screen to avoid damage to the LED panel!
It is also unsafe to get liquid on the screen. Sometimes one drop is enough if it flows down the glass onto the cables so that the TV becomes unrepairable.
