Technical description and composition of the TV MYSTERY MTV-2411LW, type of panel and applicable modules. The composition of the modules.MYSTERY LED
Model: MTV-2411LW
Chassis / Version: MSTV3208-ZC01-01
Panel: V236H1-LE5 Rev. C1
LED driver (backlight): TV2415-ZC02-01 (A) P / N: 303C2415061
Power Supply (PSU): DC12V. 3A
MainBoard: MSTV3208-ZC01-01
IC MainBoard: CPU: MST6E48RHS-LF-Z1, FLASH: S25FL032, H5PS5162GFR
Tuner: F21WT-3BAR-E
Technical Specifications MTV-2411LW
MYSTERY MTV-2411LW
General repair guidelines for TV LCD LED
Repair of electronic equipment usually begins with its external inspection and diagnosis of the malfunction. In this case, you should examine all the internal components of the TV SUPRA MTV-2411LW, as well as the external elements of the housing. Visible damage to elements can sometimes indicate the direction of the search for a defect even before the necessary measurements are taken. Elements with visible damage, for example, capacitors swelled up after boiling the electrolyte, charred resistors in certain nodes of the circuit, as well as ring cracks in solders will help the master to guess the causes and possible consequences of the malfunction.
Sometimes the SUPRA MTV-2411LW TV simply does not turn on. No control lights on the front panel are lit or blinking, the TV does not respond to the remote control and does not make any sounds or any signs of life when turned on. The most likely cause of the malfunction is the failure of the common DC12V power supply module. 3A. If it is working properly, you need to check the processor batteries on the SSB (Main Board). In the general case, first of all, it is necessary to check the electrolytic capacitors of the secondary rectifier filters and the fuse at the input of the network. If it is broken, then you should check for breakdown of the PN junctions of the rectifier bridge diodes and the key transistor of the converter, which can either be on a separate radiator or integrated with a PWM controller in a common chip. Possible options.
If a breakdown of the power switch is detected, it should be remembered that in a switching power supply (IIP) it does not fail by itself without any reasons that should be sought by checking other elements of the primary circuit - electrolytic capacitors, a PWM controller, which can only be checked replacement, as well as other semiconductor elements (diodes, transistors, zener diodes).
If the SUPRA MTV-2411LW does not have an image, but there is sound, the backlight LEDs of the V236H1-LE5 Rev.C1 panel or their power converter may malfunction. You should also make sure that the electrolytic capacitors of the secondary rectifiers of the common power supply are working.
To check the health of the LEDs and contact connections in their power circuit, the panel must be disassembled.
When diagnosing, it is necessary to take into account that it is impossible to check the open in the chain of LED lines without disassembling the panels using a tester or multimeter. To open all PN junctions connected in series, a voltage of the order of several tens of volts is required, and ideally, a current source.
Diagnostics and repair of the MSTV3208-ZC01-01 motherboard is carried out by checking the performance of the stabilizers or power converters of the module chips. In some cases, a software update is required.
Board repair and replacement of CPU chips: MST6E48RHS-LF-Z1, FLASH: S25FL032, H5PS5162GFR are carried out with the necessary equipment, and the corresponding element base. Faults associated with the application of BGA processor soldering technologies can be localized by the heating method.
Before replacing the F21WT-3BAR-E tuner, if there is no tuning for the channels, you must first check the power supply voltage at its terminals, including the power supply of varicaps (30-33V).
Once again, we remind TV users: you should not make attempts to repair it yourself without the appropriate knowledge, experience and the necessary qualifications! Trust the repair only to professionals with sufficient experience in the field of electronic equipment repair.
SCHEMATIC DIAGRAM / SERVICE MANUAL ------------------> Main mstv3208-zc01-01
FIRMWARE FOR SPI FLASH -----------> MYSTERY MTV-2411LW, Main MSTV3208-ZC01-01, PANEL V236H1-LE5 Rev.C1
The appearance of the MainBoard MSTV3208-ZC01-01 is shown in the figure below:The motherboard MSTV3208-ZC01-01 is made using the multifunction microprocessor MST6M48RHS-LF, which includes a scaler (graphic controller-scaler). To organize the work of the processor, the external RAM H5PS5162GFR 512Mb DDR2 SDRAM in BGA version and SPI FLASH 25Q32 (4Mb) are used. To provide power to the processor core, a DC / DC converter with an output voltage of 1.2V is used, assembled on the basis of the MP1482 PWM controller. Other nodes of the processor are powered by linear voltage stabilizers 2.5V, 3.3V. 1.8V voltage is used to power the DDR RAM, 3.3V is needed for the SPI FLASH ROM.
It is advisable to start the MainBoard repair by checking the supply voltage in Stand-by mode 5V and 3.3V. In operating mode, check the operation of all linear stabilizers and the DC / DC converter. If there is a backlight and there is no image, you need to check the power of the 5V or 12V panel (depending on the type of LCD panel), which should be present directly on the LVDS connector.
If the indicator signals Stand-by mode and does not respond to the remote control and control buttons, it is recommended to update the SPI Flash software. Taking into account the glitchiness of Winbond SPI chips, it is advisable to replace them with new ones in case of software failures.
MSTV3208-ZC01-01 can be used in TVs:
BBK LEM2648SD (Panel V260B1-LE9 revC1), BBK LEM3248SD (Panel HV320WX2-130 (B3)), BBK LMP3229HDU Ver1 (Panel T315HW02 v.7), BBK LMP3229HDU Ver2 (Panel T315HW04 V7), BBK LEM2649HD (Panel V260H1-LE7 Rev C1), MYSTERY MTV-2607W (Panel V260H1-L05), MYSTERY MTV-3206 (Panel T315XW04 V.7), MYSTERY MTV-3207W (Panel V315B3-L04 rev.c1), MYSTERY MTV-3213LW (Panel T315XW04 V.8), MYSTERY MTV-2220LW (Panel CLAA215FA15), MYSTERY MTV-3207W (Panel HV320WX2-110), MYSTERY MTV-2614LW (Panel V260H1-LE6), MYSTERY MTV-3208WH (Panel V315H1-L02), MYSTERY MTV-2411LW (Panel V236H1-LE5 Rev.C1), MYSTERY MTV-2618LW (Panel V260B2-LE11), MYSTERY MTV-2211LW (Panel CLAA215FA10), MYSTERY MTV-2414LW (Panel V236H1-L01), MYSTERY MTV-2611LW (Panel V260H1-LE6 Rev.C1), MYSTERY MTV-3206W (Panel T315XW03 V.3), MYSTERY MTV-3211LW (Panel V315H3-LE2 Rev. C1), MYSTERY MTV-4207WH (Panel T420HW09 V.1), MYSTERY MTV-1921LD (Panel HT185WX3).
Main features of the MYSTERY MTV-2411LW device:
Installed matrix (LED panel) V236H1-LE5 Rev. C1.
The LED driver TV2415-ZC02-01 (A) is used to power the backlight LEDs.
The formation of the necessary supply voltages for all nodes of the MYSTERY MTV-2411LW TV is carried out by the DC12V. Power module, or its analogs.
MainBoard - the main board (motherboard) is an MSTV3208-ZC01-01 module, using CPU chips: MST6E48RHS-LF-Z1, FLASH: S25FL032, H5PS5162GFR and others.
The F21WT-3BAR-E tuner provides television reception and channel tuning.
Information from an alternative source:
MYSTERY MTV-2411LW
Panel Type (Matrix): V236H1-LE5 Rev. C1
Motherboard: MSTV3208-ZC01-01, MST6E48RHS-LF-Z1, S25FL032, H5PS5162GFR, 1084 x3, AIC2857F, F4558, X50V330, 1J3N, Tuner: F21WT-3BAR.E
Invertor: TV2415-ZC02-01 (A) P / N: 303C2415061, RT8556, POWER: DC12V; 3A,
Additional technical information about the panel:
Brand: CHIMEI INNOLUX
Model: V236H1-LE5
Type: a-Si TFT-LCD, Panel
Diagonal size: 23.6 inch
Resolution: 1920x1080, FHD
Display Mode: TN, Normally White, Transmissive
Active Area: 521.28x293.22 mm
Surface: Antiglare (Haze 25%)
Brightness: 300 cd / m²
Contrast Ratio: 1000: 1
Display Colors: 16.7M (6-bit + Hi-FRC), CIE1931 72%
Response Time: 1.5 / 3.5 (Tr / Td)
Frequency: 60Hz
Lamp Type: 13S8P WLED Without Driver
Signal Interface: LVDS (2 ch, 8-bit), 30 pins
Voltage: 5.0V
MYSTERY MTV-2411LW TV with V236H1-LE5 LCD, 24 "(61 cm) diagonal size of 16: 9 format. The required screen brightness of 250 cd / m² is provided by LED backlighting. Contrast, as the ratio of maximum brightness to minimum, is 1000: 1. The LED-panel of this TV has end-face LED illumination - Edge LED.The TV design and technical features include viewing programs and movies in high quality HD at a resolution of 1920x1080 pixels in graphic resolution according to the standard 1080p (Full HD). frequency or video signal can be processed in analogue systems PAL, SECAM, NTSC .. Graphic processing and digital signal generation occurs in standards 480i, 480p, 576i, 576p, 720p, 1080i, 1080p.
The power of the acoustic system of sound 6 W (2x3 W) provide two speakers. The audio processing system NICAM STEREO is used.
The external interface (communication with other devices) is supported by standard input and output connectors: antenna input (RF), AV, audio x2, component, SCART, RGB, VGA, HDMI. To connect a computer or laptop to this TV model, use the VGA (D-Sub 15) connector on the TV, this interface supports resolutions: 800x600, 1024x768.
The power consumed by the TV in the operating mode from the network is 40 watts.
Dimensions: With stand 642x444x209 mm, Without stand 570x345x70 mm.
Attention! The V236H1-LE5 Rev.C1 panel of the MYSTERY MTV-2411LW LED TV is an expensive and unreliable element.
Avoid any impact on the glass and pressure on the surface of the screen to avoid damage to the LED panel!
It is also unsafe to get liquid on the screen. Sometimes one drop is enough if it flows down the glass onto the cables so that the TV becomes unrepairable.
