Technical description and composition of the MYSTERY MTV-3228LT2 TV, type of panel and applicable modules. The composition of the modules.MYSTERY LED
Model: MTV-3228LT2
Chassis / Version: Ver V1N03 // V6N09
Panel: LK315T3HB94 // V320BJ7-PE1
LED backlight: LED315D8-ZC14-03 (A); 2 * 9 led + 1 * 8 led
T-CON: CPWBX5409TP 04, K5387TP
LED driver (backlight): integrated into MainBoard
PWM LED driver: AP3039AM-G1, AP3608EM
Power Supply (PSU): integrated into MainBoard
PWM Power: PWM SOT23-6
MainBoard: MSDV3222-ZC01-01
IC MainBoard: CPU: MSD308BT-SW, SPI Flash: 25Q64BS1G, Scaler: NT71263FG-300
Technical Specifications MTV-3228LT2
MYSTERY MTV-3228LT2
General repair guidelines for TV LCD LED
Repair of electronic devices, including the MYSTERY MTV-3228LT2 TV, it is advisable to start with an external examination of its external and internal elements. Visible damage to elements can sometimes indicate the direction of the search for a defect even before the necessary measurements are taken. If charred resistors, swollen electrolytic or cermet capacitors, ring cracks in the soldered terminals of transformers or heating elements are detected, it is advisable to establish the causes and consequences of the malfunction that has arisen, as well as to check the connected elements and assemblies.
Malfunctions of the power module can be expressed in different ways, for example, the MYSTERY MTV-3228LT2 does not turn on at all and the control lamps on its front panel do not light up and do not blink, and there are no signs of operability. It should be noted that with the same external manifestations, the processor power regulator (converter) may be faulty. In the general case, first of all, it is necessary to check the electrolytic capacitors of the secondary rectifier filters and the fuse at the input of the network. If it is broken, then you should check for breakdown of the PN junctions of the rectifier bridge diodes and the key transistor of the converter, which can either be on a separate radiator or integrated with a PWM controller in a common chip. Possible options.
It should be remembered that in the practice of repair, usually the power switches in switching power supplies (SMPS) do not fail due to their poor quality and, in such cases, it is necessary to look for the cause that led to a malfunction and provoked a breakdown of the key. Most often, the culprits of the accident are dried electrolytic capacitors or dangling resistors in the primary circuit, or the PWM controller chip itself may be faulty. It is also necessary to check all the semiconductor elements of the stabilization circuit in the primary and secondary circuits.
If there is no image when you turn on the MYSTERY MTV-3228LT2, or it appears for a second and disappears, but there is sound, most likely there is a malfunction in the backlight LED circuit of the LK315T3HB94 panel, or in their power converter. It is necessary to check the electrolytic capacitors of the filter of the secondary rectifiers in the general power supply unit.
In most cases of lack of backlight, it becomes necessary to disassemble the panel in order to check the LEDs, connectors, loops and all contact connections. If one or several LEDs does not work in one line, therefore, they are broken and should be replaced.
To check the LED lines for breaks without disassembling the panel, for example, a current source will help. It is impossible to open series-connected PN junctions with a simple multimeter, a voltage of the order of several tens of volts is required.
When trying to repair the motherboard, you should first check the serviceability of linear stabilizers or power converters of microcircuits and, if necessary, update the software (software).
Often, the MB (SSB) card must be replaced in case of complex malfunctions that are difficult to detect. When trying to repair, you should check its elements - CPU: MSD308BT-SW, SPI Flash: 25Q64BS1G, Scaler: NT71263FG-300 and replace failed chips with new ones. Some malfunctions may be due to the use of BGA soldering technologies in modern Main Board technologies. Typically, such defects are detected by local heating of the chip.
Attention to users! Self-repair of the MYSTERY MTV-3228LT2 TV without the appropriate qualifications and experience can lead to its complete non-repairability!
FIRMWARE FOR SPI FLASH -----------> MYSTERY MTV-3228LT2, Main: MSDV3222-ZC01-01, Panel: LK315T3HB94
FIRMWARE FOR SPI FLASH -----------> MYSTERY MTV-3228LT2 VER V4N11, VER V4N10
SCHEMATIC DIAGRAM / SERVICE MANUAL ------------------> MYSTERY MTV-3224LT2 Chassis MSDV3222-ZC01-01 (MSDV3222-YL01-01)
To reduce the backlight current in LED drivers with the AP3039AM controller and the AP3608EM terminal stage (AP3039AM-G1 & AP3608EM-G1), the AP3608EM (AP3608E) microcircuit should proportionally increase the resistor from terminal 14 (ISET) to the housing. The maximum current in each channel (in milliamperes) for the Rset resistor (in kilo-ohms) is determined from the ratio 1.194V / Rset. In channels connected in parallel, the currents add up.
Repair MainBoardThe appearance of the MainBoard MSDV3222-ZC01-01 is shown in the figure below:
The motherboard MSDV3222-ZC01-01 is made on a single chassis with a power module and an inverter to power the LED panel. The MSD308BT-SW multi-function control processor with built-in scaler is used. Repair of the power module is carried out according to standard technology - verification of power cells, electrolytic capacitors and secondary supply voltages. The following is a functional check of stabilizers and converters for powering the internal nodes of the processor and LCD panel. It should be borne in mind that if there are problems with the software in the SPI Flash chips manufactured by WINBOND, it is advisable to replace the chip itself with the contents of the software.
MSDV3222-ZC01-01 can be used in TVs:
BBK LEM3284DT2 (Panel LSC320AN02), MYSTERY MTV-2229LT2 (Panel M215HTN01.1 ), MYSTERY MTV-2429LT2 (Panel M240HTN01.2), MYSTERY MTV-2223LT2 (Panel LC215DTBA), MYSTERY MTV-2431LT2 (Panel V236BJ1 600), MYSTERY MTV-1924LT2 (Panel HT185WXF-100), MYSTERY MTV-3228LT2 (Panel LK315T3HB94), MYSTERY MTV-3023LT2 (Panel MT3151A05), MYSTERY MTV-2228LT2 (Panel RUNTK0001ZDP2), MYSTERY MTV-1929LT2 (Panel V185BJ1-PE1), MYSTERY MTV-3223LT2 (Panel LC315TU3A), MYSTERY MTV-3224LT2 (Panel HV320WX2-20A), MYSTERY MTV-3028LT2 (Panel ST2751A01-3), MYSTERY MTV-2428LT2 (Panel V236BJ1-P01), MYSTERY MTV-2424LT2 (Panel HM236WU8-200 ), MYSTERY MTV-4030LT2 (Panel V400HJ6-PE1), MYSTERY MTV-3031LT2 (Panel V290BJ1-PE1), MYSTERY MTV-3226LT2 (Panel V320BJ7-PE1).
Main features of the MYSTERY MTV-3228LT2 device:
Installed matrix (LED-panel) LK315T3HB94 or V320BJ7-PE1.
The matrix control uses the Timing Controller (T-CON) CPWBX5409TP.
To power the backlight LEDs, a converter is used, combined with the main board MSDV3222-ZC01-01, controlled by a PWM controller AP3039AM-G1, AP3608EM.
The power module is combined with the MainBoard and is made according to the flyback AC / DC voltage converter circuit using PWM SOT23-6 microcircuits.
MainBoard - the main board (motherboard) is an MSDV3222-ZC01-01 module, using CPU chips: MSD308BT-SW, SPI Flash: 25Q64BS1G, Scaler: NT71263FG-300 and others.
Information from an alternative source:
MYSTERY MTV-3228LT2 Version V6N09
Panel Type (Matrix): V320BJ7-PE1
Motherboard: MSDV3222-ZC01-01
Additional technical information about the panel:
Brand: SHARP
Model: LK315T3HB94
Type: a-Si TFT-LCD, CELL
Diagonal size: 31.5 inch
Resolution: 1366x768, WXGA
Display Mode: ASV, Normally Black, Transmissive
Active Area: 697.69x392.26 mm
Surface: Antiglare, Hard coating (2H)
Glass Depth: 0.70 + 0.70 mm
Contrast Ratio: 5000: 1
Display Colors: 16.7M (8-bit)
Response Time: 7 (G to G)
Frequency: 60Hz
Signal Interface: LVDS (1 ch, 8-bit), 30 pins
Voltage: 12.0V
MYSTERY MTV-3228LT2 TV with LK315T3HB94 LCD display, 32 "(81 cm) diagonal size of 16: 9 format. The required brightness of the screen is 250 cd / m² by LED backlighting. Contrast, as the ratio of maximum brightness to minimum, is 1000: 1. Edge LED backlighting is realized in the LED-panel of this TV - Edge LED. You can view images in high quality HD at a resolution of 1366x768 pixels in the standard of graphic decomposition 720p (HD Ready). The input high-frequency or video signal can be processed in analog systems . Emah PAL, SECAM, NTSC Image processing and the formation of the digital signal is in 480i standards, 480p, 576i, 576p, 720p, 1080i, 1080p Supported multimedia file formats:. MP3, MPEG4, DivX, JPEG.
The power of the sound system 20 W (2x10 W) provides two speakers. The audio processing system NICAM STEREO is used.
The external interface (communication with other devices) is supported by standard input and output connectors: antenna input (RF), AV, VGA, HDMI x2, USB. An output for connecting headphones is provided. To connect a computer or laptop to this TV model, a VGA (D-Sub 15) connector is used on the TV case, this interface supports resolutions: 640x480, 800x600, 1024x768, 1360x768.
A digital tuner is capable of receiving television channels in the DVB-T MPEG4, DVB-C, DVB-T2 standards.
Dimensions: With stand 642x444x209 mm, Without stand 570x345x70 mm.
Attention! The LK315T3HB94 panel of the MYSTERY MTV-3228LT2 LED TV is an expensive and unreliable element.
Avoid any impact on the glass and pressure on the surface of the screen to avoid damage to the LED panel!
