MYSTERY LED
Model: MTV-1910LW
Chassis / Version: V1J07
Panel: V236H1-LE2
LED driver (backlight): integrated into MainBoard
Power Supply (PSU): Adapter
PWM Power: PWM
MainBoard: JUG7.820.807 GDCH LS507 2010.3.29
IC MainBoard: CPU: TSUMV26KU-LF, SPI Flash: EN25F40
Tuner: CDT-3FC212-00
Technical Specifications MTV-1910LW
MYSTERY MTV-1910LW
General repair guidelines for TV LCD LED
If the MYSTERY MTV-1910LW does not turn on, no control lights on the front panel light up or blink, therefore, there is a very high probability of a malfunction of the Adapter power module. In some cases, only the processor power regulator may be faulty. First of all, it is necessary to replace the swollen capacitors of the rectifier filters, if any. If the mains fuse is cut off in the power supply, in most cases a breakdown of the power key (s) is detected, which can be integrated with the PWM controller, or a separate field-effect transistor can be used. The rectifier bridge diodes and the electrolytic capacitor of the mains rectifier filter should also be checked.
The reasons for the breakdown of the power switch in switching power supplies (IIPS) can be different, for example, a malfunction of semiconductor cells or electrolytic capacitors in the stabilization circuits of the primary circuit, as well as a failure in the operation of the PWM PWM controller chip or breakage of the resistors in its bundle.
If there is no image when you turn on the MYSTERY MTV-1910LW, or it appears and immediately disappears, but there is sound, most likely there is a malfunction in the backlight LED circuit of the V236H1-LE2 panel, or in the LED node of the driver-converter of their power supply.
To check the health of the LEDs and contact connections in their power circuit, the panel must be disassembled.
When trying to detect a break in the LED lines, it should be taken into account that it is difficult to do this without disassembling the panel. For example, a current source is needed to open PN junctions connected in series.
On the JUG7.820.807 GDCH LS507 2010.3.29 motherboard, in case of a malfunction, you should first check the operation of all the stabilizers and power converters of the microcircuits, and also, if necessary, update the software (software).
In some cases, to repair the MB board (SSB), it may be necessary to replace the chips - CPU: TSUMV26KU-LF, SPI Flash: EN25F40 with new or obviously good ones. In cases where BGA technologies are used, defects are usually localized by the heating method.
If you suspect a malfunction of the CDT-3FC212-00 tuner, first of all, you need to verify the correctness of the software, as well as the presence of the necessary voltage levels and the data exchange pulses with the processor via the I2C bus on the corresponding tuner pins.
It should be remembered! Attempts to repair the MYSTERY MTV-1910LW TV, in the absence of the necessary qualifications and experience, are categorically not recommended and are fraught with negative consequences, up to the complete non-repairability of the device!Repair MainBoard
The appearance of the MainBoard JUG7.820.807 is shown in the figure below:
JUG7.820.807
JUG7.820.807 can be used on TVs:
MYSTERY MTV-1910LW (Panel V236H1-LE2), MYSTERY MTV-2410LW (Panel V236H1-LE2 Rev.C1), MYSTERY MTV-2210LW (Panel CLAA215FA04).
Main features of the MYSTERY MTV-1910LW device:
Installed matrix (LED-panel) V236H1-LE2.
To power the backlight LEDs, a converter is used, combined with the main board JUG7.820.807.
To power all the internal components of the MYSTERY MTV-1910LW TV, an external adapter type source is used using PWM chips.
MainBoard - the main board (motherboard) is a JUG7.820.807 module, using CPU chips: TSUMV26KU-LF, SPI Flash: EN25F40 and others.
The tuner CDT-3FC212-00 provides the reception of television programs and tuning to channels.
Additional technical information about the panel:
Brand: CMO
Model: V236H1-LE2
Type: a-Si TFT-LCD, Panel
Diagonal size: 23.6 inch
Resolution: 1920x1080, FHD
Display Mode: TN, Normally White, Transmissive
Active Area: 521.28x293.22 mm
Surface: Antiglare (Haze 25%), Hard coating (3H)
Brightness: 300 cd / m²
Contrast Ratio: 1000: 1
Display Colors: 16.7M (8-bit), CIE1931 70%
Response Time: 1.5 / 3.5 (Tr / Td)
Frequency: 60Hz
Lamp Type: 12S8P WLED Without Driver
Signal Interface: LVDS (2 ch, 8-bit), 30 pins
Voltage: 5.0V