Technical description and composition of the TELEFUNKEN TF-LED32S17T2 TV, panel type and modules used. The composition of the modules.TELEFUNKEN LED
Model: TF-LED32S17T2
Chassis / Version: TP.MS3463S.PB782
Panel: ST3151A05-8
T-CON: MT3151A05-5-XC-9
LED driver (backlight): integrated into MainBoard
PWM LED driver: MP3398A
MOSFET LED driver: ME15N10-G
Power Supply (PSU): integrated into MainBoard
PWM Power: PWM SOT23-6
MainBoard: TP.MS3463S.PB782
IC MainBoard: SPI FLASH: 25Q64, AUDIO: TPA3110LD2
Tuner: XF-3SDT-H (R840)
TF-LED32S17T2 Specifications
TELEFUNKEN TF-LED32S17T2
General recommendations for TV LCD LED repair
Possible manifestations of malfunctions
- The TELEFUNKEN TF-LED32S17T2 TV does not turn on, does not respond to the remote control and control panel buttons, does not light or blink indicators.
In such cases, the AC / DC converter of the mains voltage, which is combined with the main board TP.MS3463S.PB782, is often faulty. It is necessary to make sure that its output voltages are present and, if they are completely absent, check the power switches and rectifier diodes for a possible short circuit.
In case of any breakdown of semiconductors in the secondary circuits, the converter can usually operate normally in an emergency short circuit mode. There are no output voltages. And with a short circuit in the power elements of the primary circuit, as a rule, the mains fuse breaks and, less often, the current sensor in the source of the key.
Mos-Fet power switches used in switching power supplies sometimes fail due to a malfunction of any other elements that can disable it in the key mode, or create an excess of the maximum permissible key parameters. These can be elements supplying a PWM regulator, frequency setting or damper circuits, or elements of negative feedback in the stabilization circuit. PWM controllers PWM SOT23-6, in the absence of visible damage or outright short circuits between the terminals, are checked by replacing them with new ones, or knowingly working properly.
- There is no picture, but there is sound and reaction to the remote control. Or, for a second, the image may appear immediately after switching on.
As a rule, in such cases there is no display backlight. The reason for this may be an open circuit in the LED circuit, or a problem in stabilizing their power supply.
To test the LED strips, to open all the transitions of the LEDs, you need several tens of volts or more, it is best to use a current source for such purposes. The breakage of several PN junctions connected in series cannot be detected with a multimeter or tester. In such cases, it is necessary to open the panel and check each LED. If your multimeter cannot open the LED junctions in forward bias, you can sometimes detect the presence of a protective zener diode PN junction by connecting the probes in the opposite direction. If the zener diode is cut off or broken in K / Z, then the LED is faulty and requires replacement.
- The TV does not turn on, does not respond to the remote control. The indicator blinks or signals the standby mode.
Repair or diagnostics of the TP.MS3463S.PB782 motherboard should begin with checking the stabilizers and power converters necessary to power the microcircuits and matrix. If necessary, you should update or replace the software (software). In cases of complex repairs of MB (SSB) and with the necessary skills and equipment, it may sometimes be necessary to replace its SPI FLASH: 25Q64, AUDIO: TPA3110LD2 chips and other possible faulty components. Malfunctions associated with the use of BGA soldering technologies are usually easily diagnosed by the warm-up method.
The XF-3SDT-H (R840) tuner malfunction is established after checking the software and all supply voltages at its terminals. The I2C bus data exchange between the tuner and the processor can be monitored with an oscilloscope.
We remind users again! Attempts to repair the TELEFUNKEN TF-LED32S17T2 TV without proper qualifications and the necessary experience can lead to its complete non-repairability!
To reduce the backlight current, you should proportionally increase the total resistance of the resistors relative to the case at the ISET pin of the MP3398A controller. ISET (Current Setting) - Pin 8 in SOIC-20 package or Pin 6 in SOIC-16 package.
The appearance of MainBoard TP.MS3463S.PB782 is shown in the figure below:
TP.MS3463S.PB782
TP.MS3463S.PB782 can be used in TVs:
DAEWOO L32S645VTE (Panel ST3151A05-8 VER.2.4), TELEFUNKEN TF-LED32S20T2 (Panel ST3151A05-8 Ver.2.5 LVW320CSDX), TELEFUNKEN TF-LED32S17T2 (Panel ST3151A05-8).
Main features of the TELEFUNKEN TF-LED32S17T2 device:
Installed matrix (LED panel) ST3151A05-8.
Matrix control uses the Timing Controller (T-CON) MT3151A05-5-XC-9.
To power the backlight LEDs, a converter combined with the main board TP.MS3463S.PB782 is used, controlled by the PWM controller MP3398A. The keys of the ME15N10-G type are used as power elements of the LED driver.
The power module is combined with the MainBoard and is made according to the AC / DC flyback voltage converter using PWM SOT23-6 microcircuits.
MainBoard - the main board (motherboard) is a TP.MS3463S.PB782 module, using SPI FLASH: 25Q64, AUDIO: TPA3110LD2 and others.
Tuner XF-3SDT-H (R840) provides reception of television programs and tuning to channels.
Additional technical information about the panel:
Brand: CSOT
Model: ST3151A05-8
Type: a-Si TFT-LCD, CELL
Diagonal size: 31.5 inch
Resolution: 1366x768, WXGA
Display Mode: HVA, Normally Black, Transmissive
Active Area: 697.685x392.256 mm
Surface: Antiglare (Haze 2%), Hard coating (3H)
Glass Depth: 0.50 + 0.50 mm
Transmissivity: 7.16% (with Polarizer)
Contrast Ratio: 3000: 1
Display Colors: 16.7M (8-bit), CIE1931 62%
Response Time: 6.5 (G to G)
Frequency: 60Hz
Signal Interface: LVDS (1 ch, 8-bit), 30 pins
Voltage: 12.0V
PWM SMPS in SOT-23-6, SOT-26, TSOP-6 packages
In
the circuitry of modern switching power supplies (SMPS), PWM
controllers made in small-sized planar packages with six terminals have
gained wide popularity. The enclosure type designation can be SOT-23-6,
SOT-23-6L, SOT-26, TSOP-6, SSOT-6. The appearance and arrangement of the
pins are shown in the figure below. In this case, the code marking
LD7530A is shown on the left fragment of the picture.
Pin assignment:
1 - GND. (Common wire).
2
- FB. (FeedBack - Feedback). Input for controlling the duration of
pulses with a signal from the output voltage. Sometimes it can be
labeled COMP (input comparator).
3 - RI / RT / CT / COMP / NC -
Depending on the type of microcircuit, it can be used for a
frequency-setting RC circuit (RI / RT / CT), or for organizing
protection, as an input of a PWM trip comparator at a threshold value at
its input, specified in the document. In some types of microcircuits,
this input may not be used in any way (NC - No Connect).
4 - SENSE, otherwise CS (Current Sense) - Input from the current sensor at the source of the key.
5 - VCC - Input voltage supply and start of the microcircuit.
6 - OUT (GATE) - Output for controlling the gate (Gate) of the key.
Functionally,
these regulators work on the principle of the previously popular xx384x
PWM microcircuits, which have proven themselves well in terms of
reliability and stability.
Some difficulties often arise when
replacing or choosing an analog for such PWM regulators due to the use
of code markings in the designation of the type of microcircuits. The
situation is complicated by a large number of component manufacturers
who do not always provide documentation to the mass access, just as not
all manufacturers of finished devices supply repair service centers with
diagrams, so repairmen often have to study real circuit solutions by
installed components and wiring connections directly on the board.
In
practice, PWM microcircuits and the marking code EAxxx and Eaxxx are
often found. Official documentation for them was not found in the public
domain, but discussions on the forums and pieces of pictures from PDF
from System General, which publishes them as SG6848T and SG6848T2, have
survived. The drawing is here placed left .
For the attention of the masters, here below are PDF datasheet tables
compiled from information available on the Internet and PDF documents
for the selection of analogues types when replacing the most common
six-legged planar PWM with pinout pins: pin1 - GND, pin2 - FB (COMP),
pin4 - Sense, pin5 - Vcc, pin6 - OUT ...
Their main difference is the application and purpose of pin 3.
| Name | Part Number | Fabricant | Marking |
|---|---|---|---|
| SG6849 | SG684965TZ | Fairchild / ON Semi | BBxx |
| SG6849 | SG6849-65T, SG6849-65TZ | System General | MBxx EBxx |
| SGP400 | SGP400TZ | System General | AAKxx |
PWM controllers (PWM) with a 95-100 kOhm resistor on pin 3.
When
applying the PWM listed below, the frequency should be set with the RT
(RI) resistor from pin 3 to ground. Usually its nominal value is chosen
95-100 kOhm for a frequency of 65-100 KHz. For more details, see the
here below attached documentation. PDF files are packed in RAR.
| Name | Part Number | Fabricant | Marking |
|---|---|---|---|
| AP3103A | AP3103AKTR-G1 | Diodes Incorporated | GHL |
| AP8263 | AP8263E6R, A8263E6VR | AiT Semiconductor | S1xx |
| AT3263 | AT3263S6 | ATC Technology | 3263 |
| CR6848 | CR6848S | Chip-Rail | 848H16 |
| CR6850 | CR6850S | Chip-Rail | 850xx |
| CR6851 | CR6851S | Chip-Rail | 851xx |
| FAN6602R | FAN6602RM6X | Fairchild / ON Semi | ACCxx |
| FS6830 | FS6830 | FirstSemi | |
| GR8830 | GR8830CG | Grenergy | 30xx |
| GR8836 | GR8836C, GR8836CG | Grenergy | 36xx |
| H6849 | H6849NF | HI-SINCERITY | |
| H6850 | H6850NF | HI-SINCERITY | |
| HT2263 | HT2263MP | HOT-CHIP | 63xxx |
| KP201 | Kiwi Instruments | ||
| LD5530 | LD5530GL LD5530R | Leadtrand | xxt30 xxt30R |
| LD7531 | LD7531GL, LD7531PL | Leadtrend | xxP31 |
| LD7531A | LD7531AGL | Leadtrend | xxP31A |
| LD7535/A | LD7535BL, LD7535GL, LD7535ABL, LD7535AGL | Leadtrend | xxP35-xxx35A |
| LD7550 | LD7550BL, LD7550IL | Leadtrend | xxP50 |
| LD7550B | LD7550BBL, LD7550BIL | Leadtrend | xxP50B |
| LD7551 | LD7551BL/IL | Leadtrend | xxP51 |
| LD7551C | LD7551CGL | Leadtrend | xxP51C |
| NX1049 | XN1049TP | Xian-Innuovo | 49xxx |
| OB2262 | OB2262MP | On-Bright-Electronics | 62xx |
| OB2263 | OB2263MP | On-Bright-Electronics | 63xx |
| PT4201 | PT4201E23F | Powtech | 4201 |
| R7731 | R7731GE/PE | Richtek | 0Q= |
| R7731A | R7731AGE | Richtek | IDP=xx |
| SD4870 | SD4870TR | Silan Microelectronics | 4870 |
| SF1530 | SF1530LGT | SiFirst | 30xxx |
| SG5701 | SG5701TZ | System General | AAExx |
| SG6848 | SG6848T, SG6848T1, SG6848TZ1, SG6848T2 | Fairchild / ON Semi | AAHxx EAxxx |
| SG6858 | SG6858TZ | Fairchild / ON Semi | AAIxx |
| SG6859A | SG6859ATZ, SG6859ATY | Fairchild / ON Semi | AAJFxx |
| SG6859 | SG6859TZ | Fairchild / ON Semi | AAJMxx |
| SG6860 | SG6860TY | Fairchild | AAQxx |
| SP6850 | SP6850S26RG | Sporton Lab | 850xx |
| SP6853 | SP6853S26RGB, SP6853S26RG | Sporton Lab | 853xx |
| SW2263 | SW2263MP | SamWin | |
| UC3863/G | UC3863G-AG6-R | Unisonic Technologies Co | U863 U863G |
| XN1049 | XN1049, XN1049TP | Innuovo Microelectronics | 49 xxx |
PWM controllers that use pin 3 differently.
When
using the following PWM (PWM controllers), you should pay attention to
pin 3, which can be used to organize protection - thermal or from
overvoltage of the input voltage.
The frequency can be fixed at 65kHz, or set by the value of the capacitor at pin 3.
When replacing any microcircuits with analogs, carefully study the documentation. PDF files are packed in a RAR archive.
| Name | Part Number | Fabricant | Marking |
|---|---|---|---|
| AP3105/V/L/R | AP3105KTR-G1, AP3105VKTR-G1, AP3105LKTR-G1, AP3105RKTR-G1 | Diodes Incorporated | GHN GHO GHP GHQ |
| AP3105NA/NV/NL/NR | AP3105NAKTR-G1, AP3105NVKTR-G1, AP3105NLKTR-G1, AP3105NRKTR-G1 | Diodes Incorporated | GKN GKO GKP GKQ |
| AP3125A/V/L/R | AP3125AKTR-G1, AP3125VKTR-G1, AP3125LKTR-G1, AP3125RKTR-G1 | Diodes Incorporated | GLS GLU GNB GNC |
| AP3125B | AP3125BKTR-G1 | Diodes Incorporated | GLV |
| AP3125HA/HB | AP3125HAKTR-G1, AP3125HBKTR-G1 | Diodes Incorporated | GNP GNQ |
| AP31261 | AP31261KTR-G1 | Diodes Incorporated | GPE |
| AP3127/H | AP3127KTR-G1, AP3127HKTR-G1 | Diodes Incorporated | GPH GSH |
| AP3301 | AP3301K6TR-G1 | Diodes Incorporated | GTC |
| FAN6862 | FAN6862TY | Fairchild / ON Semi | ABDxx |
| FAN6863 | FAN6863TY, FAN6863LTY, FAN6863RTY | Fairchild / ON Semi | ABRxx |
| HT2273 | HT2273TP | HOT-CHIP | 73xxx |
| LD7510/J | LD7510GL, LD7510JGL | Leadtrend | xxP10 xxP10J |
| LD7530/A | LD7530PL, LD7530GL, LD7530APL, LD7530AGL | Leadtrend | xxP30 xxxP30A |
| LD7532 | LD7532GL | Leadtrend | xxP32 |
| LD7532A | LD7532AGL | Leadtrend | xxP32A |
| LD7532H | LD7532HGL | Leadtrend | xxP32H |
| LD7533 | LD7533GL | Leadtrend | xxP33 |
| LD7536 | LD7536GL | Leadtrend | xxP36 |
| LD7536R | LD7536RGL | Leadtrend | xxP36R |
| LD7537R | LD7537RGL | Leadtrend | xxP37R |
| LD7539C GL | LD7539C GL | Leadtrend | xxP39C |
| ME8204 | ME8204M6G | MicrOne | ME8204xx |
| NCP1250 | NCP1250ASN65T1G, NCP1250BSN65T1G, NCP1250ASN100T1G, NCP1250BSN100T1G | ON Semiconductor | 25xxxx |
| NCP1251 | NCP1251ASN65T1G, NCP1251BSN65T1G, NCP1251ASN100T1G, NCP1251BSN100T1G | ON Semiconductor | 5xxxxx |
| OB2273 | OB2273MP | On-Bright-Electronics | 73xx |
| R7735 | R7735AGE, R7735HGE, R7735GGE, R7735RGE, R7735LGE | Richtek | |
| UC3873/G | UC3873-AG6-R, UC3873G-AG6-R | Unisonic Technologies | U873 U873G |
TV TELEFUNKEN TF-LED32S17T2 with LCD ST3151A05-8, diagonal size 31.5 "(80 cm) 16: 9. The brightness of the screen is 270 cd / m² provided by LED backlighting. Contrast, as the ratio of maximum brightness to minimum, is 3000 : 1. The technology of production of the screen of this TV model is realized with LED backlighting. It is possible to view images in high quality HD at a resolution of 1366x768 pixels in the standard of graphic decomposition 720p (HD Ready). Supported multimedia file formats: MP3, MPEG4, Xvid, DivX, MKV , JPEG.
The power of the acoustic system of sound is 10 W (2x5 W), provided by two speakers. The NICAM STEREO audio processing system is used.
The external interface (communication with other devices) is supported by standard input and output connectors: antenna input (RF), AV, component, SCART, VGA, HDMI x2, USB. A headphone output is provided.
The digital tuner is capable of receiving television channels in the DVB-T, DVB-C, DVB-T2 standards.
Overall dimensions: 734x480x177 mm.
TV weight: 5 kg.
Attention! The ST3151A05-8 panel of the TELEFUNKEN TF-LED32S17T2 LED TV is an expensive and unreliable element.
Do not allow any impacts on the glass and pressure on the screen surface to avoid damage to the LED panel!
It is also unsafe for liquid to spill onto the screen. Sometimes one drop is enough if it drips down the glass onto the cables to make the TV non-repairable.
