Technical description and composition of the TELEFUNKEN TF-LED32S29T2 TV, panel type and modules used. The composition of the modules.TELEFUNKEN LED
Model: TF-LED32S29T2
Chassis / Version: MT31BP
Panel: LVW320CS0T E198 V4
T-CON: MT3151A05-5-XC-5
LED driver (backlight): integrated into MainBoard
PWM LED driver: MP3398A
Power Supply (PSU): integrated into MainBoard
PWM Power: PWM SOT23-6 (RT7738)
MainBoard: 40-MT31BP-MAA2LG MIPE07R41 REV1.7
IC MainBoard: CPU: MT5531NDNT 1429-BCAH; SPI Flash: 25Q64F; SOUND: RT9108NB
Tuner: 07-600CI3-SA2G ST34WN-2T-E
TF-LED32S26 Specifications
TELEFUNKEN TF-LED32S29T2
General recommendations for TV LCD LED repair
Possible manifestations of malfunctions
- The TELEFUNKEN TF-LED32S29T2 TV does not turn on, does not respond to the remote control and control panel buttons, the indicators do not light up or flash.
In such cases, the main power supply, the AC / DC converter of the mains voltage, which is combined with the MainBoard 40-MT31BP-MAA2LG, may be faulty. It is then necessary to measure its output voltages and, if they are absent, the power switches and rectifier diodes of the converters should be checked for the probability of a short circuit.
In case of breakdowns in the secondary circuits of the converter, it can usually operate in an emergency in the short-circuit mode, and with a short circuit in the power elements of the primary circuit, the mains fuse or current sensor in the source of the key is most often cut off.
Mos-Fet power switches used in switching power supplies sometimes fail due to a malfunction of any other elements that can disable it in the key mode, or create an excess of the maximum permissible key parameters. These can be elements supplying a PWM regulator, frequency setting or damper circuits, or elements of negative feedback in the stabilization circuit. PWM controllers PWM SOT23-6 (RT7738), in the absence of visible damage or outright short circuits between the terminals, are checked by replacing them with new ones, or knowingly working properly.
- There is no picture, but there is sound, it reacts to the remote control. Or the image appears when turned on and disappears immediately
The malfunction in most of these cases is found in the nodes and elements of the LED panel backlighting. The reason for this may be an open circuit in the LED circuit, or a problem in stabilizing their power supply.
Without a special current source, it is impossible to check the line of LEDs connected in series, and it is unsafe for them to use any voltage sources above 12V for this purpose. Then all that remains is to open the panel and check each LED separately. Typically, Chinese multimeters with a 9V power supply lightly light up one 3-volt LED, if you connect the probes to it in the forward direction, the red probe to the anode, and the black one to the cathode. For dual 6-volt LEDs, the PN junction of its emergency zener diode can serve as an indicator of LED health. In the event of a malfunction of the LED, its zener diode will either be cut off or broken into the K / Z.
- The indicator on the front panel blinks, the TV does not turn on in operating mode, does not respond to the remote control.
Repair or diagnostics of the 40-MT31BP-MAA2LG motherboard should begin with checking the stabilizers and power converters required to power the microcircuits and matrix. If necessary, you should update or replace the software (software). Often the MB (SSB) board needs to be replaced in case of complex malfunctions that are difficult to detect. When trying to repair, you should check its elements - CPU: MT5531NDNT 1429-BCAH; SPI Flash: 25Q64F; SOUND: MP3398A and replace the failed chips with new ones. Some malfunctions may be associated with the use of BGA soldering technologies in modern Main Board. Typically, such defects are detected by local heating of the chip.
If the TV operates normally from external devices, but does not tune to TV channels, the 07-600CI3-SA2G ST34WN-2T-E tuner may malfunction. In such cases, first of all, you should make sure that the supply voltage is present at its corresponding terminals. It is also necessary to make sure that the data exchange between the tuner and the processor is possible via the I2C bus. Sometimes the reason for the inoperability of the tuner may be a software failure.
Attention to TV owners! Attempts to repair TELEFUNKEN TF-LED32S29T2 on your own are not recommended by the manufacturer and can lead to serious negative consequences!
The appearance of the MainBoard 40-MT31BP-MAA2LG is shown in the figure below:
40-MT31BP-MAA2LG
40-MT31BP-MAA2LG can be used in TVs:
ERISSON 32LET82 (Panel LVW320CSOT E145 V2), ERISSON 32LET42T2 (Panel LVW320CSOT E274 V2), ERISSON 32LET41T2 (Panel LVW320CS0T E274 V2), FUSION FLTV-32T21 (Panel LVW320CZOT), SUPRA STV-LC32T420WL (Panel LVW320CSOT E155 V2), SUPRA STV-LC32T850WL (Panel LVW320CSOT E45 V1), SUPRA STV-LC28T662WL (Panel T8-28T3520-LPM20), SUPRA STV-LC24T850WL (Panel 720p HD 1366x768), TELEFUNKEN TF-LED32S29T2 (Panel LVW320CS0T E198 V4), TELEFUNKEN TF-LED24S29T2 (Panel V236BJ1-LE2 Rev.C1), THOMSON T24E12DHU-01B T24E12DHU (Panel LVW240AUDX E2 V6).
Main features of the TELEFUNKEN TF-LED32S29T2 device:
Installed matrix (LED panel) LVW320CS0T E198 V4.
Matrix control uses Timing Controller (T-CON) MT3151A05-5-XC-5.
To power the backlight LEDs, a converter combined with the 40-MT31BP-MAA2LG main board is used, controlled by the MP3398A PWM controller.
The power module is combined with the MainBoard and is made according to the AC / DC flyback voltage converter using PWM SOT23-6 (RT7738) microcircuits.
MainBoard - the main board (motherboard) is a 40-MT31BP-MAA2LG module, using CPU chips: MT5531NDNT 1429-BCAH; SPI Flash: 25Q64F; SOUND: RT9108NB and others.
Tuner 07-600CI3-SA2G ST34WN-2T-E provides reception of television programs and tuning to channels.
PWM SMPS in SOT-23-6, SOT-26, TSOP-6 packages
In
the circuitry of modern switching power supplies (SMPS), PWM
controllers made in small-sized planar packages with six terminals have
gained wide popularity. The enclosure type designation can be SOT-23-6,
SOT-23-6L, SOT-26, TSOP-6, SSOT-6. The appearance and arrangement of the
pins are shown in the figure below. In this case, the code marking
LD7530A is shown on the left fragment of the picture.
Pin assignment:
1 - GND. (Common wire).
2
- FB. (FeedBack - Feedback). Input for controlling the duration of
pulses with a signal from the output voltage. Sometimes it can be
labeled COMP (input comparator).
3 - RI / RT / CT / COMP / NC -
Depending on the type of microcircuit, it can be used for a
frequency-setting RC circuit (RI / RT / CT), or for organizing
protection, as an input of a PWM trip comparator at a threshold value at
its input, specified in the document. In some types of microcircuits,
this input may not be used in any way (NC - No Connect).
4 - SENSE, otherwise CS (Current Sense) - Input from the current sensor at the source of the key.
5 - VCC - Input voltage supply and start of the microcircuit.
6 - OUT (GATE) - Output for controlling the gate (Gate) of the key.
Functionally,
these regulators work on the principle of the previously popular xx384x
PWM microcircuits, which have proven themselves well in terms of
reliability and stability.
Some difficulties often arise when
replacing or choosing an analog for such PWM regulators due to the use
of code markings in the designation of the type of microcircuits. The
situation is complicated by a large number of component manufacturers
who do not always provide documentation to the mass access, just as not
all manufacturers of finished devices supply repair service centers with
diagrams, so repairmen often have to study real circuit solutions by
installed components and wiring connections directly on the board.
In
practice, PWM microcircuits and the marking code EAxxx and Eaxxx are
often found. Official documentation for them was not found in the public
domain, but discussions on the forums and pieces of pictures from PDF
from System General, which publishes them as SG6848T and SG6848T2, have
survived. The drawing is here placed left .
For the attention of the masters, here below are PDF datasheet tables
compiled from information available on the Internet and PDF documents
for the selection of analogues types when replacing the most common
six-legged planar PWM with pinout pins: pin1 - GND, pin2 - FB (COMP),
pin4 - Sense, pin5 - Vcc, pin6 - OUT ...
Their main difference is the application and purpose of pin 3.
| Name | Part Number | Fabricant | Marking |
|---|---|---|---|
| SG6849 | SG684965TZ | Fairchild / ON Semi | BBxx |
| SG6849 | SG6849-65T, SG6849-65TZ | System General | MBxx EBxx |
| SGP400 | SGP400TZ | System General | AAKxx |
PWM controllers (PWM) with a 95-100 kOhm resistor on pin 3.
When
applying the PWM listed below, the frequency should be set with the RT
(RI) resistor from pin 3 to ground. Usually its nominal value is chosen
95-100 kOhm for a frequency of 65-100 KHz. For more details, see the
here below attached documentation. PDF files are packed in RAR.
| Name | Part Number | Fabricant | Marking |
|---|---|---|---|
| AP3103A | AP3103AKTR-G1 | Diodes Incorporated | GHL |
| AP8263 | AP8263E6R, A8263E6VR | AiT Semiconductor | S1xx |
| AT3263 | AT3263S6 | ATC Technology | 3263 |
| CR6848 | CR6848S | Chip-Rail | 848H16 |
| CR6850 | CR6850S | Chip-Rail | 850xx |
| CR6851 | CR6851S | Chip-Rail | 851xx |
| FAN6602R | FAN6602RM6X | Fairchild / ON Semi | ACCxx |
| FS6830 | FS6830 | FirstSemi | |
| GR8830 | GR8830CG | Grenergy | 30xx |
| GR8836 | GR8836C, GR8836CG | Grenergy | 36xx |
| H6849 | H6849NF | HI-SINCERITY | |
| H6850 | H6850NF | HI-SINCERITY | |
| HT2263 | HT2263MP | HOT-CHIP | 63xxx |
| KP201 | Kiwi Instruments | ||
| LD5530 | LD5530GL LD5530R | Leadtrand | xxt30 xxt30R |
| LD7531 | LD7531GL, LD7531PL | Leadtrend | xxP31 |
| LD7531A | LD7531AGL | Leadtrend | xxP31A |
| LD7535/A | LD7535BL, LD7535GL, LD7535ABL, LD7535AGL | Leadtrend | xxP35-xxx35A |
| LD7550 | LD7550BL, LD7550IL | Leadtrend | xxP50 |
| LD7550B | LD7550BBL, LD7550BIL | Leadtrend | xxP50B |
| LD7551 | LD7551BL/IL | Leadtrend | xxP51 |
| LD7551C | LD7551CGL | Leadtrend | xxP51C |
| NX1049 | XN1049TP | Xian-Innuovo | 49xxx |
| OB2262 | OB2262MP | On-Bright-Electronics | 62xx |
| OB2263 | OB2263MP | On-Bright-Electronics | 63xx |
| PT4201 | PT4201E23F | Powtech | 4201 |
| R7731 | R7731GE/PE | Richtek | 0Q= |
| R7731A | R7731AGE | Richtek | IDP=xx |
| SD4870 | SD4870TR | Silan Microelectronics | 4870 |
| SF1530 | SF1530LGT | SiFirst | 30xxx |
| SG5701 | SG5701TZ | System General | AAExx |
| SG6848 | SG6848T, SG6848T1, SG6848TZ1, SG6848T2 | Fairchild / ON Semi | AAHxx EAxxx |
| SG6858 | SG6858TZ | Fairchild / ON Semi | AAIxx |
| SG6859A | SG6859ATZ, SG6859ATY | Fairchild / ON Semi | AAJFxx |
| SG6859 | SG6859TZ | Fairchild / ON Semi | AAJMxx |
| SG6860 | SG6860TY | Fairchild | AAQxx |
| SP6850 | SP6850S26RG | Sporton Lab | 850xx |
| SP6853 | SP6853S26RGB, SP6853S26RG | Sporton Lab | 853xx |
| SW2263 | SW2263MP | SamWin | |
| UC3863/G | UC3863G-AG6-R | Unisonic Technologies Co | U863 U863G |
| XN1049 | XN1049, XN1049TP | Innuovo Microelectronics | 49 xxx |
PWM controllers that use pin 3 differently.
When
using the following PWM (PWM controllers), you should pay attention to
pin 3, which can be used to organize protection - thermal or from
overvoltage of the input voltage.
The frequency can be fixed at 65kHz, or set by the value of the capacitor at pin 3.
When replacing any microcircuits with analogs, carefully study the documentation. PDF files are packed in a RAR archive.
| Name | Part Number | Fabricant | Marking |
|---|---|---|---|
| AP3105/V/L/R | AP3105KTR-G1, AP3105VKTR-G1, AP3105LKTR-G1, AP3105RKTR-G1 | Diodes Incorporated | GHN GHO GHP GHQ |
| AP3105NA/NV/NL/NR | AP3105NAKTR-G1, AP3105NVKTR-G1, AP3105NLKTR-G1, AP3105NRKTR-G1 | Diodes Incorporated | GKN GKO GKP GKQ |
| AP3125A/V/L/R | AP3125AKTR-G1, AP3125VKTR-G1, AP3125LKTR-G1, AP3125RKTR-G1 | Diodes Incorporated | GLS GLU GNB GNC |
| AP3125B | AP3125BKTR-G1 | Diodes Incorporated | GLV |
| AP3125HA/HB | AP3125HAKTR-G1, AP3125HBKTR-G1 | Diodes Incorporated | GNP GNQ |
| AP31261 | AP31261KTR-G1 | Diodes Incorporated | GPE |
| AP3127/H | AP3127KTR-G1, AP3127HKTR-G1 | Diodes Incorporated | GPH GSH |
| AP3301 | AP3301K6TR-G1 | Diodes Incorporated | GTC |
| FAN6862 | FAN6862TY | Fairchild / ON Semi | ABDxx |
| FAN6863 | FAN6863TY, FAN6863LTY, FAN6863RTY | Fairchild / ON Semi | ABRxx |
| HT2273 | HT2273TP | HOT-CHIP | 73xxx |
| LD7510/J | LD7510GL, LD7510JGL | Leadtrend | xxP10 xxP10J |
| LD7530/A | LD7530PL, LD7530GL, LD7530APL, LD7530AGL | Leadtrend | xxP30 xxxP30A |
| LD7532 | LD7532GL | Leadtrend | xxP32 |
| LD7532A | LD7532AGL | Leadtrend | xxP32A |
| LD7532H | LD7532HGL | Leadtrend | xxP32H |
| LD7533 | LD7533GL | Leadtrend | xxP33 |
| LD7536 | LD7536GL | Leadtrend | xxP36 |
| LD7536R | LD7536RGL | Leadtrend | xxP36R |
| LD7537R | LD7537RGL | Leadtrend | xxP37R |
| LD7539C GL | LD7539C GL | Leadtrend | xxP39C |
| ME8204 | ME8204M6G | MicrOne | ME8204xx |
| NCP1250 | NCP1250ASN65T1G, NCP1250BSN65T1G, NCP1250ASN100T1G, NCP1250BSN100T1G | ON Semiconductor | 25xxxx |
| NCP1251 | NCP1251ASN65T1G, NCP1251BSN65T1G, NCP1251ASN100T1G, NCP1251BSN100T1G | ON Semiconductor | 5xxxxx |
| OB2273 | OB2273MP | On-Bright-Electronics | 73xx |
| R7735 | R7735AGE, R7735HGE, R7735GGE, R7735RGE, R7735LGE | Richtek | |
| UC3873/G | UC3873-AG6-R, UC3873G-AG6-R | Unisonic Technologies | U873 U873G |
TELEFUNKEN TF-LED32S26 TV with LCD MT3151A05, 32 "(81 cm) diagonal 16: 9. The brightness of the screen is 280 cd / m² provided by LED backlighting. Contrast, as the ratio of maximum brightness to minimum brightness, is 3000: 1 The LED panel of this TV is equipped with edge LED backlighting. You can view images in high quality HD at a resolution of 1366x768 pixels in 720p (HD Ready). The input high-frequency or video signal can be processed in analog systems PAL, SECAM , NTSC Graphic processing and digital signal shaping takes place in the standards 480i, 480p, 576i, 576p, 720p, 1080i Supported multimedia file formats: MP3, WMA, MPEG4, Xvid, DivX, MKV, JPEG.
Speaker power of 16 W (2x8 W) is provided by two speakers. The NICAM STEREO audio processing system is used.
External interface (communication with other devices) is supported by standard input and output connectors: antenna input (RF), AV, component, VGA, HDMI x2, USB. A headphone output is provided. To connect a computer or laptop to this TV model, use the VGA (D-Sub 15) connector on the TV case, this interface supports resolutions: 640x480, 800x600, 1024x768, 1360x768.
Overall dimensions: 742x485x150 mm.
TV weight: 6 kg.
Attention! Panel MT3151A05 LED TV TELEFUNKEN TF-LED32S26 is an expensive and unreliable element.
Do not allow any impacts on the glass and pressure on the screen surface to avoid damage to the LED panel!
It is also unsafe for liquid to spill onto the screen. Sometimes one drop is enough if it drips down the glass onto the cables to make the TV non-repairable.
