REPAIRING AND NOT THROWING AWAY

Richtige Fernseher haben Röhren!

Richtige Fernseher haben Röhren!

In Brief: On this site you will find pictures and technical information about Service Modes, Circuit Diagrams, Firmware Update procedure, Disassemble procedure, Universal remote control set-up codes, Troubleshooting and more....

If you go into the profession, you will obtain or have access to a variety of tech tips databases HERE IT IS Master Electronics Repair !.

These are an excellent investment where the saying: 'time-is-money' rules. However, to learn, you need to develop a general troubleshooting approach - a logical, methodical, method of narrowing down the problem. A tech tip database might suggest: 'Replace C536' for a particular symptom. This is good advice for a specific problem on one model. However, what you really want to understand is why C536 was the cause and how to pinpoint the culprit in general even if you don't have a service manual or schematic and your tech tip database doesn't have an entry for your sick TV or VCR.

While schematics are nice, you won't always have them or be able to justify the purchase for a one-of repair. Therefore, in many cases, some reverse engineering will be necessary. The time will be well spent since even if you don't see another instance of the same model in your entire lifetime, you will have learned something in the process that can be applied to other equipment problems.
As always, when you get stuck, checking out a tech-tips database may quickly identify your problem and solution.In that case, you can greatly simplify your troubleshooting or at least confirm a diagnosis before ordering parts.

Happy repairing!
Today, the West is headed for the abyss. For the ultimate fate of our disposable society is for that society itself to be disposed of. And this will happen sooner, rather than later.

How to use the site:

- If you landed here via any Search Engine, you will get what you searched for and you can search more using the search this blog feature provided by Google. You can visit more posts scrolling the left blog archive of all posts of the month/year,
or you can click on the main photo-page to start from the main page. Doing so it starts from the most recent post to the older post simple clicking on the Older Post button on the bottom of each page after reading , post after post.

You can even visit all posts, time to time, when reaching the bottom end of each page and click on the Older Post button.

- If you arrived here at the main page via bookmark you can visit all the site scrolling the left blog archive of all posts of the month/year pointing were you want , or more simple You can even visit all blog posts, from newer to older, clicking at the end of each bottom page on the Older Post button.
So you can see all the blog/site content surfing all pages in it.

- The search this blog feature provided by Google is a real search engine. If you're pointing particular things it will search IT for you; or you can place a brand name in the search query at your choice and visit all results page by page. It's useful since the content of the site is very large.

Note that if you don't find what you searched for, try it after a period of time; the site is a never ending job !

..............The bitterness of poor quality is remembered long after the sweetness of todays funny gadgets low price has faded from memory........ . . . . . .....
Don't forget the past, the end of the world is upon us! Pretty soon it will all turn to dust!

©2010, 2011, 2012, 2013, 2014 Frank Sharp - You do not have permission to copy photos and words from this blog, and any content may be never used it for auctions or commercial purposes, however feel free to post anything you see here with a courtesy link back, btw a link to the original post here , is mandatory.
All posts are presented here for informative, historical and educative purposes as applicable within fair use. NOTHING HERE IS FOR SALE !

Thursday, 7 February 2019

PHILIPS FM23 PLASMA DISPLAY - SMPS WORKING PRINCIPLE

SMPS working - Philips FM23 Plasma display

Fan Control 
For ceiling mount or portrait-mode use, there is foreseen in four optional fans, grouped per two. The temperature within the monitor is measured via a sensor (R3372, KTY81) on the PSU.  This sensor is, via A/D converter (item 7530 on the SCAVIO), connected to the OTC. According the temperature within the cabinet, the OTC-software will drive the two PWM outputs of the OTC. These outputs (FAN_SP_1 and 2) are connected to the PSU, where for each signal, a corresponding voltage is generated to supply the fans. These voltages (FAN_SUPPLY_1 and _2) are proportional to the duty cycle of the corresponding PWM signals.  The OTC senses the temperature every 5 s. If it has reached T-alarm, and this value has been measured three times consequently, the monitor will go into protection, and a error code is generated.
Pre-conditioner 
Warning: the pre-conditioner does not provide mains isolation.
Introduction
The European Law describes a reduction of mains harmonics for apparatus with a power consumption above 75 W.  Therefore the pre-conditioner is designed. This module serves as the interface between the mains input and the VS/VA supply.  The advantage of a pre-conditioner is (compared to a mains input filter):
• Reduction of mains harmonics to legal limits.
• Lower mains current for the same output power.
• Power factor close to 1.
• Stable regulated output.
• Small and low weight.
The input voltage of the pre-conditioner is universal, between 95 and 264 VAC. The output is 400 VDC (400V_HOT) with a maximum output power of 300 W. This output voltage is delivered to the VS supply.
Operation
Start-up
The two relays (1450 and 1460, diagram P2) are controlled via the SUPPLY_ON signal. This signal will become 'high' when the +9V_STBY_SW, the STANDBY (from the OTC), and the LATCH signal are 'ok'. It then switches indirect relay 1450 via transistor 7460 and so enables the use of a small low voltage switch. To protect rectifier 6600 and relay 1450, the inrush current is limited to a maximum of 20 A by charging the capacitor 2605 through two serial PTCs (3450 and 3451) and an NTC (3452). After approximately 0.5 sec, relay 1460 is activated. This relay will short the PTCs. The advantage of using an NTC, is the fact that the resistance varies with the current and hence the mains voltage. At a high mains voltage, the current is lower for the same power. 
Two clamp diodes 6605 and 6606 charge output capacitors C2616 to the peak voltage of the mains input. During normal operation, both diodes are blocked because of the output voltage of 400 VDC, and will only conduct if there is a mains spike or an output dip.  Capacitor 2616 delivers via R3668 the start-up voltage at pin 16 of IC7650. After the start-up cycle, IC7650 is supplied via auxiliary winding 1-2. Capacitor C2663 is charged during the cycle that MOSFET 7610 conducts. While MOSFET 7610 is switched 'off', this capacitor transfers its energy via D6661 to the input of stabiliser IC7660. The 15 V output voltage of this IC is fed via D6665 to VCC pin 12 of IC7650.  The slow start function is realized by the circuit consisting of transistor 7654, D6654, R3654, and C2654.
Normal Operation
An up-converter circuit is used for the pre-conditioner. The switching frequency of the converter is chosen much higher than the mains frequency. It is therefore possible to consider the supply as constant, during every high frequency period, and the envelope of all voltage steps during the low frequency period approximates a half sine wave.  The output voltage of the pre-conditioner equals the input voltage, when the MOSFET is continuous switched 'off', and increases while the MOSFET is switched 'on'.  The rectified mains input voltage is connected to pin 5 of IC7650 via voltage divider R3650 and R3651. This voltage is proportional with the mains input, and is used to change the duty cycle of the pulses, which are generated at pin 11.  Because the width of these pulses is not small enough, the circuit around transistors 7640 and 7641 is added. It decreases the duration of the square wave by 500 ns (this value is set by R3640 and C2640).  A demagnetization winding (pin 1-2 of L5600) detects when there is no energy in the transformer. This information is fed to IC7650 pin 7 and this is used to switch 'on' the MOSFET (7610). In this way, the dissipation is very low, combined with a low EMI.  The MOSFET 7610 is switched 'off' at high currents, up to 15 A. To reduce dissipation, this is done at high speed for which 'turn off driver' T7608 is used.  The output voltage (400 V) is divided by R3670 and R3671 and connected to pin 3 of IC7650. A change in the load will adjust the duty cycle of the gate pulse at pin 11, in order to keep the output voltage constant. Therefore, there is no need to adjust the output voltage by means of a potentiometer.
Protections
Current Protection
The current through FET 7610 flows also through the sense resistors 3614 and 3615. The voltage across these resistors is fed to pin 6 of IC7650. If the current exceeds its reference level, the pre-conditioner will switch 'off'. A filter, formed by C2666 and R3666, avoids unnecessary protection triggering due to spikes.  C2665 and R3665 on pin 13 determine the maximum oscillating frequency.
LLC Supply.
Introduction
The VS supply (70 - 90 V) is based upon the so-called LLC converter technology (also used in the MG3.1 and FTV1.9). It is used to supply the power of the sustain pulses, which generate the light in the PDP. The voltage is set by a reference DC voltage (VRS), coming from the PDP.  The VA voltage (derived from VS, 30 - 70 V) is used to supply the power for driving the addressing electrodes of the PDP. The value of VA is also depending on a reference voltage (VRA) coming from the PDP.
The main supply hosts the following supplies:
• VS supply, via an LLC converter.
• VA supply, derived from VS via a down converter.
• VCC, via a flyback converter.
• 3V3, via a down converter.
• Audio amplifier supplies (VSND_POS and VSND_NEG), via a transformer.
The start-up voltage for the IC is derived from one phase, the IC starts to oscillate, and alternately S1 and S2 are driven into conduction with a dead time in between. This effects that, via the resonance circuit and the MOSFETS, energy is stored into transformer L5002 and capacitor C2001.
The secondary voltages are rectified and smoothed, these voltages are, via a voltage divider, fed to the optocoupler that influences the oscillator frequency of the control IC and stabilises the secondary voltages. If the current becomes too high, the supply is switched 'off' via the fault input of the control IC.
Advantages:
• High efficiency (more then 90%, other supplies 75%).
• Less radiation.
• More cost-effective (two MOSFETS of 400 V are cheaper than one MOSFET of 600 V).
Disadvantages:
• Very low power stand-by impossible.
• Realization and stabilization is more complex.
General
The LLC supply is a serial resonance power supply. The coil, resistor, and capacitor form a trap at the resonance frequency fR. The impedance is frequency dependent. The smallest impedance is at the resonance frequency (fR), at the right side of fR is the inductive part, and at the left side the capacitive part. The supply works in the inductive part, since higher frequencies causes minor losses.  Stabilization is realized, by regulating the frequency as function of the output voltage (VS_UNSW) and power. The load is stabilized by influencing the series-loop. The higher the frequency, the lower the output power.  The supply voltage of the control IC comes from the 25V_HOT voltage of the standby supply (via stabilizer 7093), and is lead to pin 15 of the IC. The IC starts to oscillate. This supply line has a short-circuit protection via opto-coupler 7003; when the supply is regulating, the current through the opto-coupler is amplified and will deliver power to the IC.  Control is done in the usual way by a TL431 at the secondary side. VRS is mixed into the feedback voltage, using an additional TL431 (7011 at schematic P6). VRS, a control signal coming from the display, influences the output of the VS supply.  The output voltage of the VS supply varies according the following formula: VS = 70 + (10 * VRS). Via this stabilization circuitry for VS, the output voltage is stabilized (if necessary, it is possible to adjust the voltage, via potmeter R3026). The VS is fed via a voltage divider to IC7010 (TL431).  If the voltage at pin 3 of IC7010 is higher than 2.5 V, a current will flow from cathode to anode. This current flows also through the secondary side of the optocoupler 7002.  The voltage at pin 7 of the MC34067, determines the output frequency. The higher this voltage, the higher the output frequency. Thus, if the voltage on pin 7 increases, the frequency increases and VS decreases.  When the output voltage rises, the voltage at the reference IC7010 also rises, this causes the current through the diode of the opto-coupler to rise. The transistor of the opto-coupler conducts more, as a result of which the voltage at pin 7 of the MC34067 increases.  The output voltage of the error amplifier gets lower, and the current through R3005 increases.  Accurate Over Voltage Protection is added, using a TL431 (7304) as reference/comparator and an additional optocoupler (7003) that acts on the fault input pin 10 of the MC34067P