REPAIRING AND NOT THROWING AWAY

REPAIRING AND NOT THROWING AWAY

Richtige Fernseher haben Röhren!

Richtige Fernseher haben Röhren!

In Brief: On this site you will find pictures and technical information about Service Modes, Circuit Diagrams, Firmware Update procedure, Disassemble procedure, Universal remote control set-up codes, Troubleshooting and more....

If you go into the profession, you will obtain or have access to a variety of tech tips databases HERE IT IS Master Electronics Repair !.

These are an excellent investment where the saying: 'time-is-money' rules. However, to learn, you need to develop a general troubleshooting approach - a logical, methodical, method of narrowing down the problem. A tech tip database might suggest: 'Replace C536' for a particular symptom. This is good advice for a specific problem on one model. However, what you really want to understand is why C536 was the cause and how to pinpoint the culprit in general even if you don't have a service manual or schematic and your tech tip database doesn't have an entry for your sick TV or VCR.

While schematics are nice, you won't always have them or be able to justify the purchase for a one-of repair. Therefore, in many cases, some reverse engineering will be necessary. The time will be well spent since even if you don't see another instance of the same model in your entire lifetime, you will have learned something in the process that can be applied to other equipment problems.
As always, when you get stuck, checking out a tech-tips database may quickly identify your problem and solution.In that case, you can greatly simplify your troubleshooting or at least confirm a diagnosis before ordering parts.

Happy repairing!
Today, the West is headed for the abyss. For the ultimate fate of our disposable society is for that society itself to be disposed of. And this will happen sooner, rather than later.

How to use the site:
- If you landed here via any Search Engine, you will get what you searched for and you can search more using the search this blog feature provided by Google. You can visit more posts scrolling the left blog archive of all posts of the month/year,
or you can click on the main photo-page to start from the main page. Doing so it starts from the most recent post to the older post simple clicking on the Older Post button on the bottom of each page after reading , post after post.

You can even visit all posts, time to time, when reaching the bottom end of each page and click on the Older Post button.

- If you arrived here at the main page via bookmark you can visit all the site scrolling the left blog archive of all posts of the month/year pointing were you want , or more simple You can even visit all blog posts, from newer to older, clicking at the end of each bottom page on the Older Post button.
So you can see all the blog/site content surfing all pages in it.

- The search this blog feature provided by Google is a real search engine. If you're pointing particular things it will search IT for you; or you can place a brand name in the search query at your choice and visit all results page by page. It's useful since the content of the site is very large.

Note that if you don't find what you searched for, try it after a period of time; the site is a never ending job !

..............The bitterness of poor quality is remembered long after the sweetness of todays funny gadgets low price has faded from memory........ . . . . . .....
Don't forget the past, the end of the world is upon us! Pretty soon it will all turn to dust!

©2010, 2011, 2012, 2013, 2014 Frank Sharp - You do not have permission to copy photos and words from this blog, and any content may be never used it for auctions or commercial purposes, however feel free to post anything you see here with a courtesy link back, btw a link to the original post here , is mandatory.
All posts are presented here for informative, historical and educative purposes as applicable within fair use. NOTHING HERE IS FOR SALE !

Saturday, 2 February 2019

SONY STR DG520 - MULTI CHANNEL AV RECEIVER - POWER AMPLIFIER, DC TO DC CONVERTER SCHEMATIC AND ADJUSTMENTS

Sony STR DG520 - MULTI CHANNEL AV RECEIVER - Power Amplifier, DC to Dc converter schematic and adjustments

US, Canadian,AEp,and UK Models
POWER OUTPUT AND TOTAL HARMONIC DISTORTION
(Models of area code US only)
With 8 ohm loads, both channels driven, from 20 – 20,000 Hz; rated 90 watts per channel minimum RMS power, with no more than 0.09 % total harmonic distortion from 250 milliwatts to rated output.
Amplifier section
Models of area code US, CND 1)
Minimum RMS Output Power (8 ohms, 20 Hz – 20 kHz, THD 0.09%) 90 W + 90 W
Stereo Mode Output Power (8 ohms, 1 kHz, THD 1%) 100 W + 100 W
Surround Mode Output Power 2) (8 ohms, 1 kHz, THD 10%) 130 W/ch
Models of area code AEP, UK 1)
Minimum RMS Output Power (8 ohms, 20 Hz – 20 kHz, THD 0.09%) 85 W + 85 W
Stereo Mode Output Power (8 ohms, 1 kHz, THD 1%) 100 W + 100 W
Surround Mode Output Power 2) (8 ohms, 1 kHz, THD 10%) 130 W/ch
US, CND 120 V AC, 60 H
AEP, UK 230 V AC, 50/60 Hz
Video section
Inputs/Outputs
Video: 1 Vp-p/75 ohms
COMPONENT VIDEO: 
Y:1 Vp-p/75 ohms
PB/CB: 0.7 Vp-p/75 ohms
PR/CR: 0.7 Vp-p/75 ohms
80 MHz HD Pass Through
AM CHANNEL STEP 9 kHz/10 kHz SELECTION MODE (US, Canadian model only)
* Either the 9 kHz step or 10 kHz step can be selected for the AM channel step.
* Procedure:
Turn the [INPUT SELECTOR] control to set AM and press the [Power] button to turn off the main power.
While depressing the [TUNING MODE] button, press the [Power] button to turn on the main power.
Either the message “9k STEP” or “10k STEP” appears for a moment and select the desired step.
Power Amplifier and DC to DC converter schematic
VACUUM FLUORESCENT DISPLAY TEST MODE
 All fluorescent segments are tested.
When this test is activated, all segments light on at the same time, then each segment lights on one after another.
 Procedure
While depressing the [TUNING MODE] and the [DISPLAY] buttons simultaneously, press the [Power] button to turn on the main power.
 Turn the [INPUT SELECTOR] control, all segments light off.
SOUND FIELD CLEAR MODE
 The preset sound field is cleared when this mode is activated.
Use this mode before returning the product to clients upon completion of repair.
 Procedure
While depressing the [2CH] button, press the [Power] button to turn on the main power.
The message “S.F. CLR.” appears for a moment and initialization is performed.
SOFTWARE VERSION DISPLAY MODE
 The software version is displayed.
 Procedure
While depressing the [SPEAKERS (ON/OFF)] and the [DISPLAY] buttons simultaneously, press the [Power] button to turn on the main power.
The model name, destination and the software version are displayed for a moment.
KEY CHECK MODE
 Button check:  Procedure
While depressing the [SPEAKERS (ON/OFF)] and the [2CH] buttons simultaneously, press the [Power] button to turn on the main power.
Either the message “REST 13” appears.
Every pressing of any button other than the [Power] counts down the buttons. The buttons which are already counted once are not
counted again. When all buttons are pressed “REST 00” appears.
SWAP ALL MODE
 The signal will be swap to all channel so that all speaker will have sound output.
 Procedure
1. While depressing the [SPEAKERS (ON/OFF)] and the [A.F.D.] buttons simultaneously, press the power [Power] button to turn on the main power.
2. “SWAP” appears. (No change while displayed.)
SHIPMENT MODE
All preset contents are reset to the default setting.
 Procedure
1. While depressing the [SPEAKERS (ON/OFF)] and the [MUSIC] buttons simultaneously, press the power [Power] button to turn on the main power.
2. “CLEARED” appears and switch off the set.
RE-BOX CLASSIFICATION TEST MODE
 Procedure
1. While pressing the [MEMORY/ENTER] and the [INPUT MODE] buttons simultaneously, press the power [Power] button to turn on the main power.
2. “R.BOX[][][]xxx” appears.
3. xx indicates number of times set powered on.
4. Press any button or power off the set to release test mode.
DCAC FACTORY TEST MODE (AEP, UK model only)
DCAC Factory Test mode have two stages
1. DCAC DSP Data Line Checking
2. DCAC board Checking
When power off
Press the three buttons [MEMORY/ENTER] + [MOVIE] + [Power] .
“DCAC[]FTM” appears.
Afterward, press the [TUNING MODE] to start DCAC factory test mode.
DCAC DSP Data Line Checking
After press the [TUNING MODE], DCAC Factory test mode will start, below display will show:
“DCAC[][][]x” x=1, 2, 3
If there is error happen, below display will show:
“ERR[]SD0x” x=1 t D1501 or R1530 problem
x=2 t D1503 problem
x=3 t D1504 problem
2. DCAC board Checking
Connect front left speaker of the receiver and AUTO CAL microphone. Turn [MASTER VOLUME] jog, there will be test tone sound output from front left speaker, and the display will change accordingly.
“AD[]-[]xxx” xxx=0 to 255 (depends on loudness of test tone)
Posted By: FRANK at 05:57
TAG: , , , ,