Technical description and composition of the HYUNDAI H-LCD2202 TV, type of panel and applicable modules. The composition of the modules.Hyundai
Model: H-LCD2202
Chassis / Version: B.TD701B-1
Panel: HT150X02-100
Inverter (backlight): INV2L-S01A
PWM Inverter: TL494C
Power Supply (PSU): Adapter 12V 3.3A
MainBoard: B.TD701B-1
IC MainBoard: PCU: TDA15021H / N1C00, Scaler: NT68565FC, Submicom: NT68F631ALG NVM: 24c16 Audio: TDA1517
Tuner: TDQ-6f6 / T126CW
Control: Remote: H-LCD2202, Service mode: CALL - RED - GREEN - YELLOW - CALL
Technical Specifications H-LCD2202
HYUNDAI H-LCD2202
General recommendations for repairing TV LCD
HYUNDAI fault diagnosis and repair with B.TD701B-1 chassis, as well as other electronic devices, is recommended to start with an external examination of the external and internal elements. In some cases, visible external damage to the elements can suggest the direction of troubleshooting and localization of the defect even before the start of the necessary measurements at the control points of the nodes of electronic circuits. In most cases, the repairman can guess the causes of the defect and possible consequences by the characteristic signs of typical TV defects, for example, ring cracks formed in the soldering of element leads, swollen rectifier filter capacitors, charred resistors and other circuit elements.
If the TV does not turn on, no indicators on its front panel are lit or blinking. Also, if the TV does not respond to the remote control and buttons, does not make any sounds or any signs of operability when turned on, there is a certain probability that the power module is defective and needs repair. Sometimes with similar manifestations a problem may occur only in the absence of processor power, which is typical for certain HYUNDAI models. When repairing the power supply, it is advisable to start the diagnostics by checking the mains fuse and the electrolytic capacitors of the filters of the converter secondary rectifiers. In the event of a fuse breaking, the reason should be sought in the power semiconductor elements of the pulse converter of the main power supply. First of all, it is necessary to check the diodes of the bridge of the rectifier of the mains voltage and the power switch (s) of the converter.
The reasons for the breakdown of the power switch in switching power supplies (IIPS) can be different, for example, a malfunction of semiconductor cells or electrolytic capacitors in the stabilization circuits of the primary circuit, as well as a failure in the operation of the PWM controller chip or broken resistors in its bundle.
If the HYUNDAI H-LCD2202 does not have an image, but there is sound and the TV is controlled from the remote control, a malfunction in the display backlight nodes is likely. The lamps or the power converter - inverter may be faulty. Often in such cases, when you turn on the TV, an image appears and immediately disappears. First of all, it is necessary to verify the operability of the electrolytic capacitors of the rectifier filter supplying the inverter, and check the LCD lamps by connecting external and obviously serviceable for diagnosis to the connectors. All necessary precautions must be observed when disabling the inverter protection during diagnostics and not leaving it disconnected after the repair is completed.
If the motherboard B.TD701B-1 is faulty, first of all it is necessary to check all the linear stabilizers or power converters of its chips, and also, if necessary, update the software. Sometimes you can check the health of MB only by replacement. In some cases, it is necessary to check or replace (if necessary) the elements of the MB board (SSB) - PCU: TDA15021H / N1C00, Scaler: NT68565FC, Submicom: NT68F631ALG NVM: 24c16 Audio: TDA1517. In cases where the BGA processor is used, its malfunction is usually detected by the local heating method.
Once again, we remind TV users: you should not make attempts to repair it yourself without the appropriate knowledge, experience and the necessary qualifications! Trust the repair only to professionals with sufficient experience in the field of electronic equipment repair.
FIRMWARE FOR SPI FLASH -----------> HYUNDAI H-LCD2202, Main: B.TD701B-1
The appearance of the MainBoard B.TD701B-1 is shown in the figure below:MainBoard B.TD701B-1 includes a TDA15021H processor, NT68565FC scaler, Submicom: NT68F631ALG, SPI FLASH 520Kb and EEPROM 2416.
It is advisable to start the repair of the motherboard by checking all voltage converters and linear stabilizers necessary to provide power to the nodes and chips in the operating and standby modes. Check the power of the LCD panel (depending on the type, + 5V or + 12V), it is convenient to measure directly on the LVDS connector. If, in the presence of the necessary supply voltage, the TV does not exit Stand-by mode, does not respond to the Remote Control and control buttons, you should update the software (firmware) SPI Flash.
B.TD701B-1 can be used in TVs:
HYUNDAI LCDVD2200 (Panel LM220WE1), HYUNDAI H-LCD2202 (Panel HT150X02-100).
Main features of the device HYUNDAI H-LCD2202:
Installed matrix (LCD panel) HT150X02-100.
The INV2L-S01A inverter is used to power the backlight lamps, it is controlled by the TL494C PWM controller.
To power all the internal components of the HYUNDAI H-LCD2202 TV, an external adapter type 112V 3.3A is used.
MainBoard - the main board (motherboard) is a B.TD701B-1 module using PCU chips: TDA15021H / N1C00, Scaler: NT68565FC, Submicom: NT68F631ALG NVM: 24c16 Audio: TDA1517 and others.
The TDQ-6f6 / T126CW tuner provides TV reception and channel tuning.
Additional technical information about the panel:
Brand: BOE
Model: HT150X02-100
Type: a-Si TFT-LCD, Panel
Diagonal size: 15.0 inch
Resolution: 1024x768, XGA
Display Mode: TN, Normally White, Transmissive
Active Area: 304.128x228.096 mm
Surface: Antiglare (Haze 25%), Hard coating (3H)
Brightness: 250 cd / m²
Contrast Ratio: 500: 1
Display Colors: 16.2M (6-bit + FRC), CIE1931 60%
Response Time: 2/6 (Tr / Td)
Frequency: 60Hz
Lamp Type: 2 pcs CCFL Without Driver
Signal Interface: LVDS (1 ch, 8-bit), 20 pins
Voltage: 3.3V
HYUNDAI H-LCD2202 TV with an HT150X02-100 LCD, diagonal size 22 "(55 cm), 16:10 format. Screen brightness of 300 cd / m² is provided by CCFL (EEFL) fluorescent lamps. Contrast, as the ratio of maximum brightness to the minimum is 700: 1. You can view images in high quality HD at a resolution of 1680x1050 pixels in the standard for graphic decomposition 720p (HD Ready). The input high-frequency or video signal can be processed in analog systems PAL, SECAM, NTSC. Graphic processing and digital signal generation happens in with Standards 480i, 480p, 576i, 576p, 720p, 1080i.
The power of the sound system 10 W (2x5 W) provides two speakers. The audio processing system NICAM STEREO is used.
The external interface (communication with other devices) is supported by standard input and output connectors: antenna input (RF), AV, audio x2, S-Video, SCART, RGB, VGA, HDMI. An output for connecting headphones is provided. To connect a computer or laptop to this TV model, a VGA (D-Sub 15) connector is used on the TV case, this interface supports resolutions: 640x480, 800x600, 1024x768.
Attention! The HT150X02-100 panel of the HYUNDAI H-LCD2202 LCD TV is its most expensive component.
Avoid hitting the glass and exerting pressure on the screen to avoid permanent damage to the LCD panel!
