Technical description and composition of the ROLSEN RL-39D1307 TV, panel type and modules used. The composition of the modules.ROLSEN LED
Model: RL-39D1307
Chassis / Version: TP.VST59.P83
Panel: V390BJ1-L01
LED backlight: 3BL-17404101-008B
T-CON: V390BJ1-XC01
LED driver (backlight): integrated into MainBoard
PWM LED driver: OB3350CP
Power Supply (PSU): integrated into MainBoard
PWM Power: PWM SOT23-6 LD7536
MOSFET Power: 7N60
MainBoard: TP.VST59.P83
IC MainBoard: CPU: TSUMV59XE, SPI FLASH: W25Q32BVS, AUDIO: TPA3110D2
Tuner: CDT-3NP5I1-10
RL-39D1307 Specifications
ROLSEN RL-39D1307
General recommendations for TV LCD LED repair
Possible manifestations of malfunctions
- ROLSEN RL-39D1307 TV does not turn on. There are no signs of operability. The indicators on the front panel do not light or blink, the TV does not respond to the remote control and control buttons.
In such cases, the AC / DC converter of the mains voltage, which is combined with the main board TP.VST59.P83, is often faulty. It is necessary to make sure that its output voltages are present and, if they are completely absent, check the power switches (7N60) and rectifier diodes for a possible short circuit.
In case of breakdowns in the secondary circuits, the converter, as a rule, can operate in an emergency mode in the short-circuit mode, and in the event of a short circuit in the power elements of the primary circuit, the mains fuse is usually cut off.
Mos-Fet keys used in switching power supplies usually fail due to a malfunction of other elements, which can disable it in key mode, or provoke an excess of the maximum current or voltage values. These can be circuits supplying the PWM controller, damper or frequency setting circuits, or OOS (negative feedback) elements in the stabilization circuit. PWM controllers (PWM) PWM SOT23-6 LD7536, in the absence of external damage and short circuit between the terminals, are checked by replacing them with a known good one.
- There is no image, there is sound, it reacts to the remote control. Or the image may appear for a second when turned on and disappear immediately.
The most likely problem in these cases is a malfunction of the LED backlight. The reason may be both in the power supply of the LEDs, in their serviceability (breakdown or breakage), as well as in the violation of the contact connections of the LED strips.
It should be remembered that it is not possible to determine an open circuit in the LED lines without disassembling the panels using a tester or multimeter without an additional device, for example, a current source. To open all PN junctions connected in series at once, a voltage of several tens of volts may be required. Then you need to open the panel and check each LED separately with a multimeter. If the capabilities of your multimeter do not allow opening the LED in the forward direction or dual LEds are used, then the PN transition of the emergency zener diode can indirectly serve as an indicator of serviceability. In the event of a malfunction of the LED-a, the PN-junction of the zener diode will either be cut off or broken through in the SC.
- The TV does not go into operation, does not respond to the remote control. The indicator on the front panel is on or blinking.
Repair or diagnostics of the TP.VST59.P83 motherboard should begin with checking the stabilizers and power converters necessary to power the microcircuits and matrix. If necessary, you should update or replace the software (software). In some cases, to repair the MB (SSB) board, it may be necessary to replace the chips - CPU: TSUMV59XE, SPI FLASH: W25Q32BVS, AUDIO: TPA3110D2 with new or known good ones. In cases where BGA technologies are used, defects are usually localized by heating.
If there is no tuning for terrestrial or cable TV channels, you should make sure that the software is correct, as well as that the supply voltages on the outputs of the CDT-3NP5I1-10 tuner match. It is also necessary to check with an oscilloscope the presence of pulses of data exchange between the tuner and the processor via the I2C bus.
We remind users again! Attempts to repair the ROLSEN RL-39D1307 TV on your own without the appropriate qualifications and the necessary experience can lead to its complete non-repairability!
DOWNLOAD FIRMWARE FOR SPI FLASH -----------> ROLSEN RL-39D1307, Main: TP.VST59.P83, Panel: V390BJ1-L01
The appearance of MainBoard TP.VST59.P83 and voltage measurements at test points are shown in the figure below:TP.VST59.P83
The TP.VST59.P83 motherboard is combined with a power supply module and is an independent device based on the TSUMV59Xxx multifunctional processor. Repair of such a board must begin with checking the power supply elements, as well as the operability of voltage converters and linear stabilizers required to provide power to certain processor nodes, in particular: core power + 1.2V, built-in DDR + 1.8V memory and standby mode node by 3.3V. The supply voltage of the LCD panel is 5V or 12V, depending on the type of panel used, it is necessary to check directly on the LVDS connector.
TP.VST59.P83 can be used in TVs:
AKAI LEA-28A08W (Panel ST2751A01-1), ERISSON 39LEN52 (Panel TLV3931-02), ERISSON 32LEN52 (Panel TLV3231-01), FUSION FLTV-32L28B (Panel TH315B051-MD1), FUSION FLTV-39LF28B (Panel V390HJ1-P02), FUSION FLTV-32L41B (Panel DBMS315LK09-C), FUSION FLTV-40LF28B (Panel DBMS400LK01-A), HYUNDAI H-LED32V18 (Panel CX315DLEDM T320XVN02.A ), MYSTERY MTV-4023LW (Panel CX390DLEDM / T390HVN04.0), ROLSEN RL-39D1305F (Panel V390HJ1-P02 Rev. C1), RUBIN RB-32D3U (Panel T320XVN01.0), RUBIN RB-39D3F (Panel CX390DLEDM), SHIVAKI STV-40LED5 (Panel V390HJ1-P01 Rev C1), SUPRA STV-LC3225AWL (Panel TH315B051-MD2), SUPRA STV-LC32T810WL (Panel TC315F3E5-A), SUPRA STV-LC32880WL (Panel HE315GH-E77GM\PW1 ), SUPRA STV-LC2825WL (Panel SM275TC30), SUPRA STV-LC32820WL (Panel TC315FJE1-MD4), SUPRA STV-LC32810WL (Panel TC315F3E5-A), TELEFUNKEN TF-LED32S7 (Panel ST3151A05-5 CX315DLEDM).
The main features of the ROLSEN RL-39D1307 device:
Installed matrix (LED panel) V390BJ1-L01.
Matrix control uses Timing Controller (T-CON) V390BJ1-XC01.
To power the backlight LEDs, a converter combined with the TP.VST59.P83 main board is used, controlled by the OB3350CP PWM controller.
The power module is combined with the MainBoard and is made according to the AC / DC flyback converter circuit using PWM SOT23-6 LD7536 chips and 7N60 type power switches.
MainBoard - the main board (motherboard) is a TP.VST59.P83 module using CPU chips: TSUMV59XE, SPI FLASH: W25Q32BVS, AUDIO: TPA3110D2 and others.
The CDT-3NP5I1-10 tuner provides reception of television programs and tuning to channels.
ROLSEN RL-39D1307 TV with LCD V390BJ1-L01, 39 "(99 cm) diagonal in 16: 9 format. The required screen brightness of 400 cd / m² is provided by LED backlighting. Dynamic contrast ratio of 500,000: 1 is achieved by special control of LED operation The LCD-panel of the TV is equipped with a direct backlighting with a rear-mounted LED - Direct LED. It is possible to view images in high quality HD at a resolution of 1366x768 pixels in a graphic resolution of 720p (HD Ready). The input high-frequency or video signal can be processed in analog PAL systems, SECAM, NTSC Graphic processing and digital signal shaping takes place in 480i, 480p, 576i, 576p, 720p, 1080i standards Supported multimedia file formats: MP3, WMA, MPEG4, Xvid, DivX, MKV, JPEG.
The sound power of the sound system is 13 W (2x6.5 W), provided by two speakers. Uses NICAM stereo signal processing system and Sound Surround function.
External interface (communication with other devices) is supported by standard input and output connectors: antenna input (RF), AV, audio x2, component, VGA, HDMI x3, USB. A headphone output is provided. To connect a computer or laptop to this TV model, a VGA (D-Sub 15) connector on the TV case is used, this interface supports resolutions: 640x480, 800x600, 1024x768, 1360x768.
The power consumed by the TV in operating mode from the network is 75 watts.
Attention! Panel V390BJ1-L01 D LED TV ROLSEN RL-39D1307 is an expensive and unreliable element.
Do not allow any impacts on the glass and pressure on the screen surface to avoid damage to the LED panel!
It is also unsafe for liquid to spill onto the screen. Sometimes one drop is enough if it drips down the glass onto the cables to make the TV unrepairable.
