ERISSON LED
Model: 19LEJ03
Chassis / Version: LA.M181.B4 1160
Panel: LM185WH2 (TL) (A1)
LED backlight: LM185WH2
T-CON: 6870S-1073A
LED driver (backlight): DP-LED-22042
Power Supply (PSU): DC12030011A
PWM Power: OB2263 (PWM SOT23-6)
MainBoard: LA.M181.B4 1160
IC MainBoard: CPU: MST6E181VS-LF-Z1; SPI Flash: W25Q32;
Tuner: TNF903SHR-BF-1
Specifications 19LEJ03
ERISSON 19LEJ03
General repair guidelines for TV LCD LED
Repair of the ERISSON 19LEJ03 TV should begin with a careful external examination of all its constituent elements and modules. Often, by the visible signs of a change in the state of some elements, one can judge the causes of the defect. Elements with visible damage, for example, capacitors swelled up after boiling the electrolyte, charred resistors in certain nodes of the circuit, as well as ring cracks in solders will help the master to guess the causes and possible consequences of the malfunction.
A malfunction of the power supply is often manifested corny - the TV does not turn on, does not make any sounds, does not light up and does not blink with any indicators. When repairing the power supply, it is advisable to start the diagnostics by checking the mains fuse and the electrolytic capacitors of the filters of the converter secondary rectifiers. In the event of a fuse breaking, the reason should be sought in the power semiconductor elements of the pulse converter of the main power supply. First of all, it is necessary to check the diodes of the rectifier bridge of the mains voltage and the power key (s) of the converter. The complete inoperability of the power supply unit can be caused by a short circuit in the power elements in the primary circuit, followed by an open fuse, or a short circuit in the loads.
As a rule, the keys in switching power supplies (SMPS) are reliable enough and rarely fail for no reason to be looked for by checking other components of the circuit - electrolytic capacitors, resistors and semiconductor elements of the primary circuit. The PWM chip is verified by replacing it with a known good one.
If the ERISSON 19LEJ03 TV does not have an image, but there is sound, a malfunction in the backlight circuits of the LM185WH2 LED panel (TL) (A1) is likely.
In case of breaks in the LED circuit, a complete disassembly of the panel is required, the LEDs are checked for an open circuit, as well as the reliability of the connections in the connectors and rations of the terminals.
To detect a break in the LED lines without disassembling the panel, a current source is required. It is impossible to open transitions connected in series with a simple multimeter; voltage of several tens of volts is necessary.
When trying to repair the motherboard, you should first check the serviceability of linear stabilizers or power converters of microcircuits and, if necessary, update the software (software).
In cases of attempts to repair the MB board (SSB), it is necessary to check the health of its elements - CPU: MST6E181VS-LF-Z1; SPI Flash: W25Q32; which may require replacement with new ones. If a BGA processor is installed, there is a possibility of a violation of the soldering of the contacts of its conclusions with the board (it is diagnosed by heating).
Before changing the TNF903SHR-BF-1 tuner, if it is not possible to tune to television channels, make sure that there are supply voltages that must be measured at the corresponding tuner pins and check the software for correctness.
Attention! For users and owners of 19LEJ03 TVs who do not have the appropriate qualifications, knowledge and experience, we categorically do not recommend attempting self-repair in order to avoid negative consequences that could lead to complete non-repairability of the device.
FIRMWARE FOR SPI FLASH -----------> ERISSON 19LEJ03 , Main: LA.M181.B4 1160, Panel: LM185WH2 (TL)(A1)
The appearance of MainBoard LA.M181.B4 is shown in the figure below:
LA.M181.B4
LA.M181.B4 can be used in TVs:
ERISSON 16LEJ02 (Panel LP156WH4 TL B1), ERISSON 19LEJ02 (Panel LM185WH2 (TL)(A1)), ERISSON 16LEJ03 (Panel LP156WD1 TL A1), ERISSON 24LEJ02 (Panel V236H1-LE2), ERISSON 22LEJ031 (Panel LM215WF4), ERISSON 24LEJ03 (Panel V236H1-LE4 REV C1), ERISSON 19LEJ03 (Panel LM185WH2 (TL)(A1)), ERISSON 22LEJ02 (Panel LTM215HT03).
The appearance of the power supply
Main features of the ERISSON 19LEJ03 device:
The matrix (LED panel) LM185WH2 (TL) (A1) is installed.
The matrix control uses the Timing Controller (T-CON) 6870S-1073A.
The LED driver DP-LED-22042 is used to power the backlight LEDs.
The required supply voltages for all nodes of the TV ERISSON 19LEJ03 are generated by the DC12030011A power supply module or its analogs using OB2263 microcircuits (PWM SOT23-6).
MainBoard - the main board (motherboard) is a LA.M181.B4 module, using CPU chips: MST6E181VS-LF-Z1; SPI Flash: W25Q32; and others.
The TNF903SHR-BF-1 tuner provides television reception and channel tuning.
Additional technical information about the panel:
Brand: LG Display
Model: LM185WH2-TLA1
Type: a-Si TFT-LCD, Panel
Diagonal size: 18.5 inch
Resolution: 1366x768, WXGA
Display Mode: TN, Normally White, Transmissive
Active Area: 409.8x230.4 mm
Surface: Antiglare, Hard coating (3H)
Brightness: 250 cd / m²
Contrast Ratio: 1000: 1
Display Colors: 16.7M (8-bit), CIE1931 68%
Response Time: 1.1 / 3.9 (Tr / Td)
Frequency: 60Hz
Lamp Type: 3 strings WLED Without Driver
Signal Interface: LVDS (1 ch, 8-bit), 30 pins
Voltage: 5.0V
ERISSON 19LEJ03 TV with LM185WH2 LCD display, 19 "(48 cm) diagonal size in 16: 9 format. The LED panel of this TV has LED backlighting - Edge LED. You can view images in high quality HD at a resolution of 1366x768 pixels in standard for graphic decomposition 720p (HD Ready). The input high-frequency or video signal can be processed in analog systems PAL, SECAM, NTSC. Graphic processing and digital signal generation occurs in standards 480i, 480p, 576i, 576p, 720p, 1080i. Supported media file formats : MP3, MPEG4, DivX, JPEG. Stereo sound is realized by two built-in speakers, and NICAM STEREO audio processing system is used.
The external interface (communication with other devices) is supported by standard input and output connectors: antenna input (RF), AV, audio x2, component, SCART, RGB, VGA, HDMI, USB. An output for connecting headphones is provided. To connect a computer or laptop to this TV model, a VGA (D-Sub 15) connector is used on the TV case, this interface supports resolutions: 640x480, 800x600, 1024x768, 1280x1024, 1360x768.
The power consumed by the TV in the operating mode from the network is 30 watts.
Overall dimensions: With stand 463x360x45 mm, Without stand 442x279x46 mm.
Attention! The LM185WH2 (TL) (A1) panel of the ERISSON 19LEJ03 LED TV is an expensive and unreliable element.
Avoid any impact on the glass and pressure on the surface of the screen to avoid damage to the LED panel!
It is also unsafe to get liquid on the screen. Sometimes one drop is enough if it flows down the glass onto the cables so that the TV becomes unrepairable.