Technical description and composition of the ERISSON 24LEB15 TV, type of panel and applicable modules. The composition of the modules.ERISSON LED
Model: 24LEB15
Chassis / Version: T.VST29.A2B
Panel: M240HW01 VD
MainBoard: T.VST29.A2B 12313
IC MainBoard: CPU: TSUMV59XU-Z1; SPI Flash: W25Q32
Tuner: CDT-3SP5I2-36
Specifications 24LEB15
ERISSON 24LEB15
General repair guidelines for TV LCD LED
Any repair usually begins with an external inspection. Often, based on certain external signs, it may be possible to draw certain conclusions about the reasons for the failure of certain elements of the circuit even before the necessary measurements are made, which will determine the further algorithm for troubleshooting and localizing the defect. Ring cracks in the soldering of the leads of the heating elements, swollen electrolytic capacitors, a charred paint layer on the resistors - all this for the repairman can be a significant clue in the assumptions about the causes and consequences of the malfunction.
If the 24LEB15 TV does not turn on, does not make any sounds when turned on, and also no indicators on the front panel light or blink - there is a high probability of a malfunction in the power module. In some cases, only the stabilizer or power converter of the control processor may be faulty, which is typical for some ERISSON models. It is advisable to start the troubleshooting of the power supply module by checking the state of the electrolytic capacitors of the rectifier filters and the mains fuse. Defective capacitors should be replaced. If the mains fuse is broken, it is necessary to check first of all the power semiconductor elements - rectifier diodes and transistors, which are often found in such a state of breakdown.
In most cases, key breakdowns in switching power supplies (SMPS) do not occur for no reason and you should look for other faulty circuit elements that could provoke a defect. This can be dried electrolytic capacitors in the primary circuit, and faulty damper elements, as well as dangling resistors or punched semiconductor elements in the stabilization circuits. Possible defective PWM chip from the manufacturer.
If the ERISSON 24LEB15 does not have an image, but there is sound and the TV is controlled by the remote control, a malfunction in the backlight circuits of the M240HW01-VD panel is likely. The LEDs or the power converter - LED driver may be faulty. Often in such cases, when you turn on the TV, an image appears and immediately disappears. First of all, it is necessary to verify the operability of the electrolytic capacitors of the rectifier filter supplying the LED driver, and check the LEDs, connecting obviously known good diagnostics.
A malfunction in the backlight circuits often occurs due to an open in the power circuit of the LED lines. It requires disassembling the panel and checking the LEDs themselves, the rations of their terminals, as well as the reliability of the connections in the connectors and rations of the terminals.
A break in the line of LEDs connected in series cannot be detected with a multimeter or tester without disassembling the panel. To open all the transitions, several tens of volts are needed, and it is best to use a current source for such purposes.
Repair or diagnostics of the T.VST29.A2B 12313 motherboard should begin by checking the stabilizers or power converters of its microcircuits. If necessary, you should update the software (software).
If it is not possible to replace the MB (SSB) card, you need to check the health of its elements - CPU: TSUMV59XU-Z1; SPI Flash: W25Q32. Defective components should be replaced.
Before replacing the tuner CDT-3SP5I2-36, if there is no tuning for the channels, you must first check the supply voltage at its terminals.
For owners of the 24LEB15 TV, we recommend that you contact qualified professionals with experience to repair! Self-repair attempts without the appropriate knowledge and skills can lead to serious negative consequences!
FIRMWARE FOR SPI FLASH -----------> ERISSON 24LEB15, Main: T.VST29.A2B 12313, Panel: M240HW01-VD
The appearance of MainBoard T.VST29.A2B is shown in the figure below:T.VST29.A2B
T.VST29.A2B can be used in TVs:
DNS E19A00 (Panel CX185LEDM (V185B1-PE)), DNS E22A11 (Panel M215HGE-P02), DNS E22A00 (Panel CX215LEDM M215HGE-P01), DNS E16A20 (Panel TL156WH4 (TL)(N2)), ERISSON 22LEB15 (Panel M215HW01), ERISSON 19LEB15 (Panel M185XW01), ERISSON 24LEB15 (Panel M240HW01 VD), ROLSEN RL-19L1003U (Panel M185BGE-L10 Rev.C1), ROLSEN RL-22L1003U (Panel V216BG1-LE1 REV C1), ROLSEN RL-23L1003UF (Panel M230HGE-L20 Rev.C1), ROLSEN RL-23L1005UF (Panel M230HGE-L20 RevC1).
Main features of the ERISSON 24LEB15 device:
Installed matrix (LED-panel) M240HW01 VD.
The required supply voltage for all nodes of the TV ERISSON 24LEB15 provides a switching power supply.
MainBoard - the main board (motherboard) is a T.VST29.A2B module, using CPU chips: TSUMV59XU-Z1; SPI Flash: W25Q32 and others.
The tuner CDT-3SP5I2-36 provides the reception of television programs and tuning to channels.
Additional technical information about the panel:
Brand: AUO
Model: M240HW01 VDQ0
Type: a-Si TFT-LCD, Panel
Diagonal size: 24.0 inch
Resolution: 1920x1080, FHD
Display Mode: TN, Normally White, Transmissive
Active Area: 531.36x298.89 mm
Surface: Antiglare, Hard coating (3H)
Brightness: 250 cd / m²
Contrast Ratio: 1000: 1
Display Colors: 16.7M (6-bit + Hi-FRC)
Response Time: 3.5 / 1.5 (Tr / Td)
Frequency: 60Hz
Lamp Type: 20S4P WLED Without Driver
Signal Interface: LVDS (2 ch, 8-bit), 30 pins
Voltage: 5.0V
ERISSON 24LEB15 TV with M240HW01 LCD, 24 "(61 cm) diagonal size of 16: 9 format. The required screen brightness of 300 cd / m² is provided by LED backlighting. Contrast, as the ratio of maximum brightness to minimum, is 1000: 1. The LED panel of this TV uses end LED backlighting - Edge LED.The TV’s design and technical features include viewing programs and movies in high quality HD at a resolution of 1920x1080 pixels in a graphic resolution of 1080p (Full HD) standard. the audio or video signal can be processed in analogue systems PAL, SECAM, NTSC. Graphic processing and digital signal generation occurs in the standards 480i, 480p, 576i, 576p, 720p, 1080i, 1080p. Stereo sound is realized by two built-in speakers. The audio processing system NICAM STEREO is used .
The external interface (communication with other devices) is supported by standard input and output connectors: antenna input (RF), AV, S-Video, component, VGA, HDMI x3, USB. An output for connecting headphones is provided. To connect a computer or laptop to this TV model, a VGA (D-Sub 15) connector is used on the TV case, this interface supports resolutions: 640x480, 800x600, 1024x768, 1280x1024, 1360x768.
Overall dimensions: With stand 373x270x120 mm, Without stand 524x340x44 mm.
Attention! The M240HW01 VD panel of an ERISSON 24LEB15 LED TV is an expensive and unreliable element.
Avoid any impact on the glass and pressure on the surface of the screen to avoid damage to the LED panel!
It is also unsafe to get liquid on the screen. Sometimes one drop is enough if it flows down the glass onto the cables so that the TV becomes unrepairable.
