Technical description and composition of the HYUNDAI H-LED19V13 TV, type of panel and applicable modules. The composition of the modules.HYUNDAI LED
Model: H-LED19V13
Chassis / Version: T.MS6M181.7A
Panel: CX185LEDM
LED driver (backlight): JJG7820.842
Trans LED driver: 220
MainBoard: T.VST59.62 // T.MS6M181.7A
IC MainBoard: MST6E181VS-LF-Z1, W9425G6JH-4, GD25Q32, YD1517
Tuner: CDT-3NP5 / 1-10 // AFT7 / W1
Technical Specifications H-LED19V13
HYUNDAI H-LED19V13
General repair guidelines for TV LCD LED
HYUNDAI H-LED19V13, like other televisions, it is advisable to start repairing with a careful examination of the external and internal elements and modules. Visible damage to elements can sometimes indicate the direction of the search for a defect even before the necessary measurements are taken. Swollen electrolytic or cermet capacitors, charred resistors, ring cracks in the soldered terminals of the elements - all this can significantly help the master to determine the causes and consequences of the malfunction of the TV.
If the TV does not turn on, no indicators on its front panel are lit or blinking. Also, if the TV does not respond to the remote control and buttons, does not make any sounds or any signs of operability when turned on, there is a certain probability that the power module is defective and needs repair. Sometimes with similar manifestations a problem may occur only in the absence of processor power, which is typical for certain HYUNDAI models. When diagnosing and repairing the power supply, first of all, replace the swollen filter capacitors of the secondary rectifiers and check the fuse and, if it is broken, it is necessary to identify the cause. Often in such cases, an avalanche (thermal) breakdown is detected in the power semiconductor elements of the module — rectifier diodes and transistors in the primary circuit.
It should be remembered that in the practice of repair, usually the power switches in switching power supplies (SMPS) do not fail due to their poor quality and, in such cases, it is necessary to look for the cause that led to a malfunction and provoked a breakdown of the key. Most often, the culprits of the accident are dried electrolytic capacitors or dangling resistors in the primary circuit, or the PWM controller chip itself may be faulty. It is also necessary to check all the semiconductor elements of the stabilization circuit in the primary and secondary circuits.
If the HYUNDAI H-LED19V13 does not have an image, but there is sound, there may be a malfunction of the panel backlight LEDs or their power converter. You should also make sure that the electrolytic capacitors of the secondary rectifiers of the common power supply are working.
Often there is a need for disassembling the panel to check the health of the LEDs, as well as contact connections in the connectors and soldering.
It should be remembered that it is not possible to determine the open circuit in the LED lines without disassembling the panels with a tester or multimeter without an additional device, for example, a current source. To open all PN junctions connected in series at once, a voltage of several tens of volts may be required.
In cases of attempts to repair the motherboard T.MS6M181.7A, it is necessary to check the operability of the stabilizers or power converters of its microcircuits and, if possible, update the software (software). BGA chips can in most cases be diagnosed by local heating.
If it is not possible to replace the MB (SSB) card, you need to check the health of its elements - MST6E181VS-LF-Z1, W9425G6JH-4, GD25Q32, YD1517. Defective components should be replaced.
If there is no reception of television channels, but the TV is working properly from external devices, first of all you need to check the voltage of the varicaps of the tuner AFT7 / W1, which is usually within 30-33V, as well as other supply voltages on the terminals of the tuner.
Owners and users of the HYUNDAI H-LED19V13 TV must remember that self-repair without special knowledge, skills and qualifications can be fraught with negative consequences that can lead to complete non-repairability of the device!
SCHEMATIC DIAGRAM / SERVICE MANUAL ------------------> HYUNDAI H-LED19V13 Chassis: T.MS6M181.7A
The appearance of MainBoard T.VST59.62 is shown in the figure below:T.VST59.62
It is advisable to start the repair of the T.VST59.62 motherboard based on the TSUMV59Xxx multifunction processor by checking the operability of linear voltage stabilizers or voltage converters necessary to provide power to the processor nodes - 1.2V core power, 1.8V DDR memory and Stand-by 3.3V mode . If there is no image, but the display backlight is working properly, you should check the power supply voltage of the LCD panel 5V or 12V, depending on the type of panel used.
T.VST59.62 can be used on TVs:
Akai LEA-22V21M (Panel A215ED1DA3-1), ERISSON 22LEN18 (Panel M215HGJ-L21), ERISSON 16LEN18 (Panel N156BGE-L11 Rev.C1), ERISSON 24LEN18 (Panel M236HGE-L20), Fusion FLTV-16L10B (Panel T156LL10-AW4), FUSION FLTV-24T9 (Panel M240HW01 V.B), FUSION FLTV-16T9 (Panel B156XTN02), FUSION FLTV-16T9D (Panel T156LL10-AW4), HYUNDAI H-LED19V13 (Panel CX185LEDM ), SUPRA STV-LC19811FL (Panel M185XTN01.3), SUPRA STV-LC19820WL (Panel LM185WH2), SUPRA STV-LC22820FL (Panel LS215AFTNM), SUPRA STV-LC18250WL (Panel B173HW02 V.1), SUPRA STV-LC22810FL (Panel M215HGE-L21 Rev.C1), SUPRA STV-LC16810WL (Panel B156RW01 V.1), SUPRA STV-LC18251FL (Panel N173HGE-L11 Rev. C1), SUPRA STV-LC22811FL (Panel 1080p Full HD 1920x1080), SUPRA STV-LC1982WL (Panel 1080p Full HD 1920x1080), TELEFUNKEN TF-LED22S3 (Panel M215HGE-P02).
Main features of the HYUNDAI H-LED19V13 device:
Installed matrix (LED-panel) CX185LEDM.
The LED driver JJG7820.842 is used to power the backlight LEDs. A transformer 220 is installed in the LED driver converter.
The required supply voltage for all nodes of the HYUNDAI H-LED19V13 TV provides a switching power supply.
MainBoard - the main board (motherboard) is a T.VST59.62 module, using microcircuits MST6E181VS-LF-Z1, W9425G6JH-4, GD25Q32, YD1517 and others.
The tuner CDT-3NP5 / 1-10 // AFT7 / W1 provides the reception of television programs and tuning to channels.
HYUNDAI H-LED19V13 TV with CX185LEDM LCD display, 19 "(48 cm) diagonal size in 16: 9 format. The required screen brightness of 220 cd / m² is provided by LED backlighting. Contrast, as the ratio of maximum brightness to minimum, is 1000: 1. Edge LED backlighting is realized in the LED-panel of this TV - Edge LED. You can view images in high quality HD at a resolution of 1366x768 pixels in the standard for graphic decomposition 720p (HD Ready). The input high-frequency or video signal can be processed in an analog system max PAL, SECAM, NTSC. Graphic processing and digital signal generation occurs in the standards 480i, 480p, 576i, 576p, 720p, 1080i. Supported media file formats: MP3, WMA, MPEG4, Xvid, DivX, MKV, JPEG.
The power of the acoustic system of sound 6 W (2x3 W) provide two speakers. The audio processing system NICAM STEREO is used.
The external interface (communication with other devices) is supported by standard input and output connectors: antenna input (RF), AV, audio x2, component, SCART, VGA, HDMI, USB. An output for connecting headphones is provided. To connect a computer or laptop to this TV model, a VGA (D-Sub 15) connector is used on the TV case, this interface supports resolutions: 640x480, 800x600, 1024x768, 1360x768.
The power consumed by the TV in the operating mode from the network is 36 watts.
Overall dimensions: with a support 456x340x139 mm, without a support 456x311x49 mm.
TV Weight: 2.8 kg.
Attention! The CX185LEDM panel of a HYUNDAI H-LED19V13 LED TV is an expensive and unreliable element.
Avoid any impact on the glass and pressure on the surface of the screen to avoid damage to the LED panel!
It is also unsafe to get liquid on the screen. Sometimes one drop is enough if it flows down the glass onto the cables so that the TV becomes unrepairable.
