Technical description and composition of the HARPER 24F470T TV, panel type and modules used. The composition of the modules.HARPER LED
Model: 24F470T
Chassis / Version: TP.S512.PA63
Panel: CX236DLEDM
LED driver (backlight): integrated into MainBoard
PWM LED driver: SN51DP
MOSFET LED driver: PA1108DA
Power Supply (PSU): integrated into MainBoard
PWM Power: LD5530
MOSFET Power: TO-252
MainBoard: TP.S512.PA63
IC MainBoard: CPU: S2T512, SPI Flash: GD25Q64, Audio: YD1517P
Tuner: XF-3SDT-H (R840)
Specifications 24F470T
HARPER 24F470T
General recommendations for TV LCD LED repair
Possible malfunctions
- TV HARPER 24F470T does not turn on and does not give any signs of turning on, does not respond to control buttons and to the remote control.
First of all, in such cases, you should make sure that the common switching power supply (SMPS) - the AC / DC voltage converter of the mains voltage - is working. All source elements in this TV model are located on the MainBoard TP.S512.PA63. Its output voltages should be measured and, if they are absent, the serviceability of the power switches (TO-252) and rectifier diodes in the converters should be checked for possible breakdown.
In case of breakdowns in the secondary circuits, the converter can operate in short-circuit mode, and in case of short-circuit in the elements of the primary circuit, the mains fuse usually breaks.
Mos-Fet power switches used in switching power supplies sometimes fail due to a malfunction of any other elements that can disable it in the key mode, or create an excess of the maximum permissible key parameters. These can be elements supplying a PWM regulator, frequency setting or damper circuits, or elements of negative feedback in the stabilization circuit. PWM controllers LD5530, in the absence of visible damage or outright short circuits between the terminals, are checked by replacing them with new ones, or known to be in good working order.
- There is no image, there is sound, it reacts to the remote control. Or, immediately after switching on for a second, the image may appear and immediately disappear.
Usually, in such cases, a malfunction is detected in the nodes of the backlight of the LED panel. The reason may be in the breakage of the LEDs, in the stabilization of their power supply, or in the violation of the contact connections of the strings connectors,
Without a special current source, it is impossible to check the line of LEDs connected in series, and it is unsafe for them to use any voltage sources above 12V for this purpose. Then it remains only to open the panel and check each LED separately. Typically, Chinese multimeters with a 9V power supply lightly light up one 3-volt LED, if you connect the probes to it in the forward direction, the red probe to the anode, the black one to the cathode. For dual 6-volt LEDs, the PN junction of its emergency zener diode can serve as an indicator of LED health. In the event of a malfunction of the LED, its zener diode will either be cut off or broken into the K / Z.
- The indicator on the front panel blinks, the TV does not turn on in operating mode, does not respond to the remote control.
Repair or diagnostics of the TP.S512.PA63 motherboard should begin with checking the stabilizers and power converters necessary to power the microcircuits and matrix. If necessary, you should update or replace the software (software). In some cases, to repair the MB (SSB) board, it may be necessary to replace the chips - CPU: S2T512, SPI Flash: GD25Q64, Audio: YD1517P with new or known good ones. In cases where BGA technologies are used, defects are usually localized by heating.
If the TV operates normally from external devices, but does not tune into TV channels, the XF-3SDT-H (R840) tuner may be faulty. In such cases, first of all, you should make sure that the supply voltage is present at its corresponding terminals. It is also necessary to make sure that the data exchange between the tuner and the processor is possible via the I2C bus. Sometimes the reason for the inoperability of the tuner may be a software failure.
Once again, we remind TV users: do not attempt to repair yourself without the appropriate knowledge, experience and the necessary qualifications! Trust the repair to professionals with sufficient experience in the field of electronic repair.
DOWNLOAD FIRMWARE FOR SPI FLASH -----------> HARPER 24F470T, Main: TP.S512.PA63, Panel: CX236DLEDM
The appearance of the MainBoard TP.S512.PA63 is shown in the figure below:TP.S512.PA63
TP.S512.PA63 can be used in TVs:
AIWA 24LE7021 (Panel V236BJ1-P03), ERISSON 22LES71T2 (Panel A215EE1TBA-9), FUSION FLTV-24H100T (Panel CM238C01), SUPRA STV-LC22T800FL (Panel C215F14-E1-P), THOMSON T24E14DF-01B (Panel HM236WU3-101).
The main features of the HARPER 24F470T device:
Installed matrix (LED-panel) CX236DLEDM.
To power the backlight LEDs, a converter combined with the TP.S512.PA63 main board is used, controlled by the SN51DP PWM controller. The keys of the PA1108DA type are used as power elements of the LED driver.
The power module is combined with the MainBoard and is made according to the AC / DC flyback voltage converter using LD5530 microcircuits and TO-252 power switches.
MainBoard - the main board (motherboard) is a TP.S512.PA63 module, using CPU chips: S2T512, SPI Flash: GD25Q64, Audio: YD1517P and others.
Tuner XF-3SDT-H (R840) provides reception of television programs and tuning to channels.
HARPER 24F470T TV with LCD CX236DLEDM, diagonal 24 "(61 cm) in 16: 9 format. The required screen brightness of 220 cd / m² is provided by LED backlighting. Dynamic contrast ratio of 50,000: 1 is achieved by a special control of the LEDs. the screen of this TV model is realized with LED backlighting.The design and technical capabilities of the TV provide viewing of broadcasts and films in high quality HD at a resolution of 1920x1080 pixels in graphic decomposition according to the standard 1080p (Full HD) Supported media file formats: MP3, MPEG4, JPEG.
The power of the sound system of 6 W (2x3 W) is provided by two speakers. The NICAM STEREO audio processing system is used.
The external interface (communication with other devices) is supported by standard input and output connectors: antenna input (RF), AV, component, VGA, HDMI, USB. A headphone output is provided.
The digital tuner is capable of receiving television channels in the DVB-T MPEG4, DVB-C, DVB-T2 standards.
Overall dimensions: 557x370x175 mm.
TV weight: 2.6 kg.
Attention! Panel CX236DLEDM LED TV HARPER 24F470T is an expensive and unreliable element.
Do not allow any impacts on the glass and pressure on the screen surface to avoid damage to the LED panel!
It is also unsafe for liquid to spill onto the screen. Sometimes one drop is enough if it drips down the glass onto the cables to make the TV non-repairable.
