Washing machines and Washers error codes - Fault codes

GE front lading washing machine error codes

E22 – Water Fill timeout

E23 – Flood protect drain

E30 – Drain pump not present

E31 – Drain timeout

E38 – Dispenser error

E39 – Dispenser timeout

E42 – Drive motor

E43 – DC Fault

E45 – Drive motor

E46 – Drive motor

E47 – Heat sink

E48 – Drive motor

E49 – Load too heavy

E4A – Under volts

E4B – Power up problems

E4C – Over volts

E4E – Under volts after start

E4F – EEProm fault

E52 – Main control

E53 – Buffer error Internal software buffer error

E54 – No motor response

E57 – Checksum failure

E58 – Communication failure

E60 – Door lock switch failure

E61 – Door unlock switch failure

E62 – System contact failure

E63 – Unexpected open door

E64 – Unexpected open door while running

E65 – Water level sensor failure

E66 – Water temperature sensor open

E67 – Water temperature sensor shorted

E70 – Stuck key

E71 – Key fault Communication error

GE WSL washing machine error codes

IE – Water level sensor error

7E – Water supply error

E – Drain pump error

dE – Lid open error

UE – Unbalance switch error

OE – Water overflow error

IFB Washing Mahcines error code/fault codes
1:IFB Washing Machine Not Turning ON OR Turns ON But Does not Starts.
2:IFB Washing Machine Door Does Not Opening. DE Error
3: Water is not coming inside the IFB Washing Machine Inlet problem
4:Water is Leaking from the washing machine, drum or hose pipe damaged
5:Wash is not happening / Spin not Happening in the IFB Washing Machine
6:Drum NOt rotating or Drum Making Huge Sound while spin cycle,
7:Water not Draining From the washing Machine
8:Burning smell, Tripping Problem, etc
IFB Amana washing machine error codes
“Sd” – (Excess suds)
F8 followed by E1 – (water supply error)
F9 followed by E1 – (drain pump system error)
F5 followed by E2 – (door will not lock)
F7 followed by E1 – (motor drive error)
“rL” – (remove load)
Washer making error beeps – Door has not been opened and closed for at least 3 cycles
Washer beeps when HOLD TO START is touched – Door not closed
F# E# code other than as described above appears in display – System Code Error
“nt” (interrupted) – Cycle was paused or cancelled
Clean Washer LED flashing at end of wash cycle – The washer has run 30 wash cycles and is indicating a reminder to run the Clean Washer cycle.

IFB Asko washing machine error codes

F1 – Water supply/low water fill
F2 – Water level too high
F3 – Pump problem
F4 – Thermistor problem
F5 – Fault in thermal cutout or heating pause fault
F6 – Motor fault
F7 – Door lock release fault
00 – Machine did not spin

Beko washer error codes

H1 – NTC Open or Short Circuit
H2 – Heater Open Circuit
H3 – Heater Always On
H4 – Valve Triac Short Circuit
H5 – Pump Open Circuit
H6 – Motor Triac Short Circuit
H7 – Pressure Sensor Failure
H11 – Motor & or Tacho Open Circuit

Bosch washing machine error codes

F16 – Door lock error

F17 – Inlet valve error detected
F18 – Drain error detected
F23 – Anti flood device has been activated
F34 – Door lock error
F42 – Motor fault
F43 – Motor fault
F44 – Motor fault

Bosh WAE range washing machine error codes

F16 – Door lock problem
F17 – Inlet valve
F18 – Drain pump
F21 – Motor
F23 – Anti flood system activated

Bosch WEP range washing machine error codes

F01 – Water intake timeout
F02 – Heating timeout
F03 – Draining timeout
F04 – Motor fault
F05 – Uncontrolled motor startup
F06 – Short on NTC Detected on hot water intake
F07 – Open circuit NTC Open circuit wiring
F08 – Door open when program started
F09 – Unexpected heating
F10 – Communication error
F11 – Overheating
F12 – Short circuit
F13 – Mains voltage too high
F14 – Mains voltage too low
F15 – Faulty temperature sensor on motor PCB
F16 – Faulty rinse sensor Displayed only in test

Daewoo washing machine error codes

E2 = Water has overfilled and the error code is displayed

E5 = High Voltage Error

E7 = Directional Error

E8 = Washer Motor Error

E9 = Pressure Sensor Error

H2 = Wash Temperature Sensor

H4 = Overheating Washer Heating Element

H6 = Washer Heating Element Failed

H8 = Heater Overheating / No Water Washer

IE = Water Inlet Error – Washing Machine Did Not Fill With Water

LE = Washing Machine Door Open

OE = Water Has Not Drained From The Washer

PEF = Filter Is Detected As Blocked

UE = Washer Load Imbalance

Fisher & Paykel to-load aqua smartwashing machine error codes

21, 26, 27, 49, 50, or 246 = Water Inlet Valve Fault

38 or 39 = Water Level Pressure Transducer Air Tube Fault

58 or 68 = Water Level Pressure Transducer Fault

10, 41, or 237 = Water Temperature Sensor Fault

1, 57, 60, 107, 108, 112, 133, 220, 221, 222, 223, 224, 225, 226, 230, 232, 233, 236, 241, 243, 252, or 254 = Motor Control Module Fault

45, 46, 103, 104, 105, 106, or 241 = Display Module Fault

234, 235, 238, or 239 = Lid Lock is Bad

40, 56, or 160 = Spin Basket Will Not Engage Or Disengage From Clutch

136 or 137 = Motor Is Not Running

37, 114, 245, 247, 248, 249, 250, or 253 = Water Is Not Draining

Frigidaire front loading washing machne error codes

E10 – Water doesn’t enter

E20 – Water dosen’t drain

E30 – Drum overfilled

E40 – Door is open

E50 – Motor is overheated

E70 – Cold water doesn’t enter

EF0 – Over sudsing

EF0 – Hot water doesn’t enter

E11 – Fill time too long

E13 – Water leak in tub or air leak

E21 – Water not pumping out fast enough

E23 – Drain pump relay on control board failed or wire off pump

E24 – Drain pump relay on control board failed or wire off pump

E31 – Pressure sensor not communicating with control board

E35 – Pressure sensor indicates water overfill

E36 – Control board problem

E41 – Control board thinks the door switch is open

E43 – Control board problem

E44 – Control board problem

E45 – Control board problem

E46 – Control board problem

E47 – Board thinks door PTC circuit is open in spin

E48 – Board thinks door PTC circuit is closed

E52 – Bad signal from tacho generator

E56 – High motor current

E57 – High current on motor phase

E59 – No tacho signal for 3 seconds

E5A – High temp on heat sink caused by overloading

E5B – High temp on heat sink

E5C – High temp on heat sink

E5D – Communication problem

E5E – Communication problem

E5F – Communication problem

E66 – Heating element relay failure

E67 – Input voltage on microprocessor incorrect

E68 – Current leakage to ground on heater or fuse opened

E70 – The control board is not seeing the correct water supply

E71 – Wash NTC failure

E74 – Wash temperature does not increase

E75 – Water temperature sensor circuit

E76 – NTC temperature for the cold water valve over the limits

E82 – Console control problem

E83 – Console control problem

E91 – Communication error between UI board and control board

E93 – Console control problem

E94 – Console control problem

E95 – Communication error

E97 – Console control problem

E98 – Console control problem

EB1 – Incoming power frequency out of limits

EB2 – Incoming line voltage above 130 vac

EB3 – Incoming line voltage below 90 VAC

EF1 – Clogged drain pump

EF2 – Too much soap

EBE – Console control problem

EBF – Console control problem

EF5 – NTC temperature for the hot water valve over the limits

F1 – Internal fault in control

F2 – Water temperature problem

F3 – Water level problem

F4 – Washer is not advancing

F5 – Keypad problem

Haier washing machine error codes

bLoC PunP – Water not draining out / No drain

no tAPS – Not filling up with water

Err1 – Washing machine door error detected = Not closed

Err2 – Water has not drained from the washer

Err3 – Detected washer temperature sensor error

Err4 – Washer heating element fail

Err5 – Water level not reached expected level

Err6 – Washing machine motor speed incorrect

Err7 – Motor speed error detected

Err8 – Washer has overfilled with water

ErLC – Door lock has failed

ErUL – Door lock failure

EUAr – Communication failure between display board and power board

Unb – Unbalanced wash load

PF – Voltage is less than 93 Volts AC

CLrF – Too much detergent suds

Hotpoint washing machine error codes

F01 – Electronic circuit board fault

F02 – Motor circuit fault

F03 – Temperature sensing fault

F05 – Waste pipe blockage or pump issue

F06 – Door lock fault

F07 – Electronic circuit board fault / heating circuit fault

F08 – Heater fault

F09 – Software fault

F11 – Pump circuit fault

F12 – Electronic control fault

F13 – Dryer temperature sensing fault (washer dryers only)

F15 – Heater control fault (washing machines and washer dryers)

F16 – Drum lock position sensor fault (top loading machines only)

F18 – Internal data error

F19 – Fan motor or heating fault (washer dryers only)

Kenmore Oasis Whirlpool Cabrio and Maytag Bravos washer error codes

LF – Long Fill

Ld – Long Drain

uL – Unbalanced Load

oL – Overloaded

Sd – Suds Detection

id – Open or Close Lid

Po – Pump Out

HC – Hot and Cold reversed

dL – Lid Lock Failure

dU – Lid Unlock Failure

F1 – Pressure Signal Out-of-Range

F2 – Keypad Interface Failure

F40 – Thermistor Open

F41 – Motor RPS Thermistor Open

F42 – Heater in Unknown state

F43 – Heater is continuously On

F44 – Heater cannot be turned On

F50 – Motor Stalled

F51 – Motor RPS Failure

F52 – Motor Stop Failure

F53 – Motor Control Over temp

F54 – Motor Control Over current

F72 – Basket Re-engagement Failure

LG front loader washing machine error codes

IE – Water inlet error

UE – Unbalance error

OE – Drain error

FE – Over flow

PE – Pressure sensor error

dE – Door open error

CE – Oven current error

LE – Locked motor error

bE – Ball sensor error

EE – EEprom error

PF – Power failure

E1 – Leakage error

Maytag front loading Neptune washer error codes

DO – Door Open

FL – Failed to lock

LO – Door failed to unlock

Lr – Locked Motor Rotor

ND – No Drain

NF – No Fill

OD – Opened Door

Sd – Suds lock

PF – Power failure

Samsung Front load – Top load washer error codes

dc – Unbalanced load

dL – Door is not locked when washer is running

FL – Washer failed to lock the door

Hr – Water temperature control problem

LE – Washer tried to fill but has not reached correct water level

LO – Door will not unlock

E3 – Motor not running properly

nd – Washer is not draining

nF – Washer tried to fill

4E – Washer cannot fill with water

Sr – Problem with control

PF – Power failure

OE – Water level sensor

bE – Motor speed sensor

tE – Temperature sensor

3E – High current detected

2E – High/low voltage detected

5r – Problem with control

8E – Vibration sensor

Whirlpool AQ, AW model washer error codes

FH – No Water Inlet

FA – Aquastop Failure

FP – Drain Failure

F5 – NTC Failure

F6 – Tachometer Failure

F7 – Triac Short Circuit detection

F8 – Heating Element, Open Circuit

F9 – Overflow Failure

F10 – Motor control unit (Thermal)

F11 – Communication failure

F12 – Heating Element Short Circuit

F13 – Dispenser Circuit Error

F14 – EEPROM Failure

F15 – Motor Control Unit Error

F16 – Control Failure (Control Unit)

F18 – Control Failure (Control Unit)

F20 – Control Failure (Control Unit)

F21 – Control Failure (User Board)

F22 – Control Failure (User Board)

FDL – Door Lock Error

FDU – Door Unlock Error