Technical description and composition of the PHILIPS 32PFL3517H TV, type of panel and applicable modules. The composition of the modules.PHILIPS LED
Model: 32PFL3517H / 60
Chassis / Version: TPM9.2E LA
Panel: LC320EUE (SE) (M1)
LED backlight: 6922L-0011A, 6920L-0001C, 6916L0801B, 32 V12 Edge REV0.4 2
LED driver (backlight): integrated into PSU
Power Supply (PSU): 715G5194-P01-W20-002S
PWM Power: LD7523GS, A6069H
MainBoard: 715G5155-M01-002-005X (VerA)
IC MainBoard: MT5366ZVGG, H5TQ1G63DFR-H9C, TMDS361BPAGR
Tuner: ENV57U04D8F
Control: IR: 715G5251-R01-000-004I
Specifications 32PFL3517T
PHILIPS 32PFL3517H
General repair guidelines for TV LCD LED
Possible malfunctions
- The PHILIPS 32PFL3517H does not turn on. There are no signs of operability. The indicators on the front panel do not light or flash, the TV does not respond to the remote control and control buttons.
In some of these cases, a malfunction is detected in the 715G5194-P01-W20-002S power module. It is necessary to measure its output voltages, and in case of their absence, check the operability of the power switches of the converters and rectifier diodes for the probability of short circuit.
In case of breakdowns of semiconductors in the secondary circuits of any converter, as a rule, it can operate in emergency short-circuit mode without output voltages, and during short circuit in the elements of the primary circuit, the main fuse and, less often, the current sensor at the source of the key are most often cut off.
Breakdown of power switches (MosFet) in pulsed sources is sometimes caused by malfunctions of other circuit elements, for example, in circuits supplying a PWM controller, frequency-setting or damper ones, as well as in negative feedback circuits (OOS) of stabilization. PWM controllers (PWM) LD7523GS, A6069H, if they do not have visible damage to the chassis and open short circuit between the terminals, are usually checked by replacement.
- There is no image, but there is sound and reaction to the remote control. Or for a second, the image may appear immediately after switching on.
In such cases, the most likely malfunction of the LED backlight. The reason can be both in the power supply of the LEDs, in their serviceability (breakdown or breakage), as well as in the violation of the contact connections of the LED strips.
It is impossible to check the LED line for breaks without disassembling the panel with a multimeter or tester. For these purposes, it is necessary to open all series-connected PN junctions and a voltage of the order of tens of volts will be required, and ideally, a current source. Having disassembled the panel, it is necessary to check each LED separately. Chinese multimeters, as a rule, light up a single 3-volt LED in the forward direction. In the case of using dual 6-volt LEDs, the PN junction of its protective zener diode can serve as a health indicator. In faulty LEDs, the zener diode will either be cut off or broken into short-circuit.
- The indicator on the front panel blinks, the TV does not turn on in the operating mode, it does not respond to the remote control.
Repair or diagnostics of the 715G5155-M01-002-005X motherboard should be started by checking the stabilizers and power converters needed to power the microcircuits and matrix. If necessary, update or replace the software (software). When repairing an MB board, you need to check its components MT5366ZVGG, H5TQ1G63DFR-H9C, TMDS361BPAGR. Defective items should be replaced. If chips with BGA soldering technology are used, a problem in its implementation is detected by the local heating of the chip.
Before replacing the tuner ENV57U04D8F, if there is no tuning for the channels, you must first check the software and the supply voltage at its terminals. It is also necessary to make sure that the tuner and processor can exchange data via the I2C bus
It should be remembered! Attempts to independently repair the PHILIPS 32PFL3517H TV, in the absence of the necessary qualifications and experience, are categorically not recommended and are fraught with negative consequences, up to the complete non-repairability of the device!
Service manual and schematic diagram 32PFL3517H/60 Chassis TPM9.2E LA
for models 32PFL3517H/12, 32PFL3507K/02, 32PFL3517K/02, 37PFL3507H/12, 37PFL3507K/02, 42PFL3507H/12, 42PFL3507K/02
The appearance of the MainBoard 715G5155-M01-002-005X is shown in the figure below:715G5155-M01-002-005X
715G5155-M01-002-005X can be used in TVs:
PHILIPS 22PFL3507T/60 (Panel M215HW03 V.1 code 174 p/n: 996590001935 code 160 932228935682), PHILIPS 24PFL3507T/60 (Panel M236HGE-L20 code 161 p/n: 996590000202), PHILIPS 32PFL3517/60 (Panel LC320EUE (SE)(M1) code 156 p/n: 932228889682), PHILIPS 37PFL3507T/60 (Panel LC370EUE (SE)(M1)), PHILIPS 42PFL3007H/60 (Panel LC420WUE (SC)(A1) code 152 p/n: 932228942682), PHILIPS 32PFL3517H/60 (Panel LC320EUE (SE)(M1)).
The appearance of the power supply
Main features of the PHILIPS 32PFL3517H device:
Installed matrix (LED-panel) LC320EUE (SE) (M1).
To power the backlight LEDs, a converter is used, combined with a power supply.
The necessary supply voltages for all nodes of the PHILIPS 32PFL3517H TV are generated by the power module 715G5194-P01-W20-002S, or its analogs using microcircuits LD7523GS, A6069H.
MainBoard - the main board (motherboard) is a module 715G5155-M01-002-005X, using chips MT5366ZVGG, H5TQ1G63DFR-H9C, TMDS361BPAGR and others.
The ENV57U04D8F tuner provides TV reception and channel tuning.
Additional technical information about the panel:
Brand: LG Display
Model: LC320EUE-SEM1
Type: a-Si TFT-LCD, Panel
Diagonal size: 31.5 inch
Resolution: 1920x1080, FHD
Display Mode: S-IPS, Normally Black, Transmissive
Active Area: 698.4x392.85 mm
Surface: Antiglare (Haze 1%), Hard coating (3H)
Brightness: 400 cd / m²
Contrast Ratio: 1400: 1
Display Colors: 16.7M (8-bit), CIE1931 68%
Response Time: 6 (G to G)
Frequency: 60Hz
Lamp Type: 7S6P WLED Without Driver
Signal Interface: LVDS (2 ch, 8-bit), 51 pins
Voltage: 12.0V
