Technical description and composition of the SAMSUNG UE32ES6757M TV, panel type and applicable modules. The composition of the modules.SAMSUNG LED
Model: UE32ES6757M
Chassis / Version: CS01
Panel: LE320CSM-C2
LED backlight: SLED 2012SVS32 7032NNB 44 2D REV1.0
T-CON: V400HK05-CPS1
LED driver (backlight): integrated into PSU; 87.5V 470mA
PWM LED driver: SLC5012M
MOSFET LED driver: D5N40, D3N40
Power Supply (PSU): BN44-00517C
PWM Power: SSC2S110, A358F, PWM SOT23-6
MOSFET Power: D4189, MDD1752
MainBoard: BN41-01807A BN94-05857F
IC MainBoard: WT61P805, KLM2G1HE3F-B001, K4B2G1646C-HCK0, NTP7412S
Tuner: BN40-00236A DNSD243VH144A
Control: BN41-01831A
Appearance
SAMSUNG UE32ES6757M
General repair guidelines for TV LCD LED
Possible malfunctions
- The SAMSUNG UE32ES6757M TV does not turn on and does not show any signs of turning on, it does not respond to the control buttons or the remote control.
With such manifestations, a malfunction is most likely to be detected in the BN44-00517C power supply module. It is necessary to measure its output voltages, and in case of their absence (full or partial), it is necessary to check the serviceability of power switches (D4189, MDD1752) of converters and rectifier diodes for the presence of a possible short circuit.
In case of breakdowns of semiconductors in the secondary circuits, the converter can usually work abnormally in the short circuit mode, and during short circuit in the power elements of the primary circuit, the mains fuse often breaks.
The breakdown of power switches (MosFet) in pulsed sources is sometimes caused by malfunctions of other circuit elements, for example, in circuits supplying a PWM controller, frequency-setting or damper ones, as well as in negative feedback (OOS) stabilization circuits. PWM controllers (PWM) SSC2S110, A358F, PWM SOT23-6, if they do not have visible damage to the case and open fault between the terminals, are usually checked by replacement.
- There is no image, but there is sound and reaction to the remote control. Or for a second, the image may appear immediately after switching on.
As a rule, in such cases there is no display backlight. The reason can be both in the power supply of the LEDs, in their serviceability (breakdown or breakage), as well as in the violation of the contact connections of the LED strips.
To check the health in the LED circuit, it is better to use a current source with a maximum voltage of 200V. We do not recommend using any voltage sources for this purpose. You can check each LED individually with a simple Chinese multimeter (powered by 9 volts) in the P-N-junction test mode. If you connect the red probe of the multimeter to the anode of the LED, and the black to its cathode, then the 3-volt LED will light up slightly, and in the opposite direction you can detect the transition of the emergency zener diode. A zener diode PN junction indirectly indicates a LED-a
- The indicator blinks or glows constantly, the TV does not turn on, does not respond to the remote control.
Repair or diagnostics of the BN41-01807A motherboard should begin by checking the stabilizers and power converters needed to power the chips and matrix. If necessary, you should update or replace the software (software). Sometimes it is necessary to check or replace (if necessary) the elements of the MainBoard board - WT61P805, KLM2G1HE3F-B001, K4B2G1646C-HCK0, NTP7412S. In cases where the BGA processor is used, its malfunction is usually detected by the local heating method.
Before replacing the tuner BN40-00236A DNSD243VH144A, if there is no tuning for the channels, you must first check the software and the supply voltage at its terminals. It is also necessary to make sure that the tuner and processor can exchange data via the I2C bus
Attention! For users and owners of UE32ES6757M TVs who do not have the appropriate qualifications, knowledge and experience, we categorically do not recommend attempting self-repair in order to avoid negative consequences that could lead to complete non-repairability of the device.
SCHEMATIC -------------> SAMSUNG UE32ES6757, UE32ES6757M Chassis U78A/U79A Model: UE**ES61***, UE**ES63***, UE**ES65***, UE**ES67***, UE**ES68***.
The appearance of the MainBoard BN41-01807A is shown in the figure below:
BN41-01807A
BN41-01807A can be used in TVs:
SAMSUNG UE40ES6550S (Panel LTJ400HV05-V), SAMSUNG UE46ES6547U UE46ES6547 (Panel LTJ460HW06-L), SAMSUNG UE40ES7207U (Panel LTJ400HL10-L), SAMSUNG UE46ES6540 UE46ES6540U (Panel LTJ460HW06-L), SAMSUNG UE40ES6750 MXRU (Panel LTJ400HV08-L), SAMSUNG UE32ES6727U UE32ES6727 (Panel LTJ320HW06-L), SAMSUNG UE40ES6757 UE40ES6757M (Panel LTJ400HV08-L), SAMSUNG UE32ES6550 UE32ES6550S (Panel LE320CSM-C1), SAMSUNG UE40ES6540S (Panel LTJ400HV07-L), SAMSUNG UE55ES6760 UE55ES6760SXZG (Panel LTJ550HW10-B), SAMSUNG UE32ES6540 UE32ES6540S (Panel LE320CSM-C1), SAMSUNG UE40ES6727 UE40ES6727U (Panel LTJ400HV08-L), SAMSUNG UE32ES6757M (Panel LE320CSM-C2).
The appearance of the power supply
Main features of the SAMSUNG UE32ES6757M device:
Installed matrix (LED panel) LE320CSM-C2.
The matrix control uses the Timing Controller (T-CON) V400HK05-CPS1.
To power the backlight LEDs, a converter is used, combined with a power supply unit, controlled by the SLC5012M PWM controller. As power elements of the LED driver, keys of the type D5N40, D3N40 are used.
The necessary supply voltages for all nodes of the SAMSUNG UE32ES6757M TV are generated by the BN44-00517C power supply module or its analogs using SSC2S110, A358F, PWM SOT23-6 microcircuits and power switches of the D4189, MDD1752 type.
MainBoard - the main board (motherboard) is a BN41-01807A module, using microchips WT61P805, KLM2G1HE3F-B001, K4B2G1646C-HCK0, NTP7412S and others.
The tuner BN40-00236A DNSD243VH144A provides the reception of television programs and tuning to channels.
