
SAMSUNG LED
Model: UE40F6470 UE40F6470SS
Chassis / Version: HIGH_X12_Union
Panel: CY-HF400CSLV2H
T-CON: BN41-01939C LSF400HF02 2013_TCON_FOX_FT1
LED driver (backlight): integrated into PSU
PWM LED driver: SLC2013M
MOSFET LED driver: KF9N25
Power Supply (PSU): BN44-00622B L42X10_DHS
PWM Power: FSFR1800HS, SPC7011F (PFC), SQD3011K
MOSFET Power: STF13NM60
MainBoard: BN41-01958B BN94-06725Q HVR1
IC MainBoard: SEMS30, WT61P807, K4B2G1646E, KLM4G1FE3B, 25Q40, 25Q40, WT61P807, TAS5745
Tuner: BN40-00262B CT2CX-3S / K3S
Technical Specifications UE40F6470
SAMSUNG UE40F6470
General repair guidelines for TV LCD LED
Possible malfunctions
- SAMSUNG UE40F6470 does not turn on, the indicators on the front panel do not light or flash. The TV does not respond to the control buttons and the remote control.
In some of these cases, a fault is detected in the BN44-00622B power module. Then we recommend that you measure its output voltages and, if they are absent, you should check the health of the power switches (STF13NM60) and rectifier diodes of the converters for possible short circuit.
In the event of breakdowns in the secondary circuits of the converter, it can usually fail in short circuit mode, and in the event of a short circuit in the power elements of the primary circuit, the mains fuse or current sensor at the source of the key most often breaks.
The breakdown of Mos-Fet keys used in pulsed sources is often caused by malfunctions of other elements, for example, in the power supply circuit of a PWM controller, in frequency-setting or damping circuits, as well as in Negative Stabilization Feedback. PWM chips FSFR1800HS, SPC7011F (PFC), SQD3011K are usually checked by replacing with new ones, or obviously working.
- There is no image, but there is sound and reaction to the remote control. Or for a second, the image may appear immediately after switching on.
Failure in most such cases is detected in the nodes and backlight elements of the LED panel. The reason can be both in the power supply of the LEDs, in their serviceability (breakdown or breakage), as well as in the violation of the contact connections of the LED strips.
To detect a break in the LED lines without disassembling the panel, a current source is required. It is impossible to open transitions connected in series with a simple multimeter; voltage of several tens of volts is necessary.
- The TV does not turn on, does not respond to the remote control. The indicator blinks or signals standby mode.
Repair or diagnostics of the BN41-01958B motherboard should begin by checking the stabilizers and power converters needed to power the chips and matrix. If necessary, you should update or replace the software (software). In cases of complex repairs of MB (SSB) and in the presence of the necessary skills and equipment, sometimes it may be necessary to replace its chips SEMS30, WT61P807, K4B2G1646E, KLM4G1FE3B, 25Q40, 25Q40, WT61P807, TAS5745 and other possible faulty components. Malfunctions associated with the application of BGA soldering technologies are usually easily diagnosed by the heating method.
Before changing the tuner BN40-00262B CT2CX-3S / K3S, if it is not possible to tune to television channels, make sure that there are supply voltages that must be measured at the corresponding terminals of the tuner and check the software for correctness. The pulses of the data exchange of the tuner with the processor can be controlled by an oscilloscope
TV users and owners must remember that attempts to self-repair a SAMSUNG UE40F6470 TV without the appropriate qualifications and necessary experience can lead to serious negative consequences!

The appearance of the MainBoard BN41-01958B is shown in the figure below:
BN41-01958B
BN41-01958B can be used in TVs:
SAMSUNG UE39F5500 UE39F5500AK (Panel HF390BGM-C1), SAMSUNG UE32F5300AK (Panel HF320BGA-B1), SAMSUNG UE40F6200AK (Panel CY-HF400BGLV2V), SAMSUNG UE32F4500AK (Panel HF32AGH-R1), SAMSUNG UE42F5300AK (Panel CY-HF420BGAV1V), SAMSUNG UE46F6500 AK (Panel CY-HF400CSLV1V), SAMSUNG UE46F6330AK UE46F6330 (Panel CY-HF460CSLV2V), SAMSUNG UE32F6330 AK (Panel CY-HF320CSLV1V), SAMSUNG UE40F6330AK UE40F6330 (Panel CY-HF400CSLV5V), SAMSUNG UE40F6510AB UE40F6510 (Panel CY-GF400CSLV2V), SAMSUNG UE55F6400AK UE55F6400 (Panel CY-HF550CSLV1V), SAMSUNG UE40F6540AB (Panel CY-GF400CSLV3V), SAMSUNG UE40F6500 UE40F6500SS (Panel CY-GF400CSLV1H), SAMSUNG UE46F6650 UE46F6650AB (Panel CY-GF460CSLV1V), SAMSUNG UE46F6510 UE46F6510AB (Panel CY-GF460CSLV2V), SAMSUNG UE50F6330 UE50F6330AK (Panel HF500CSA-B1).
The appearance of the power supply
Main features of the SAMSUNG UE40F6470 device:
Installed matrix (LED-panel) CY-HF400CSLV2H.
The matrix control uses the Timing Controller (T-CON) BN41-01939C.
To power the backlight LEDs, a converter is used, combined with the power supply, controlled by the SLC2013M PWM controller. As the power elements of the LED driver, keys of the KF9N25 type are used.
The necessary supply voltages for all nodes of the SAMSUNG UE40F6470 TV are generated by the BN44-00622B power supply module or its analogs using the FSFR1800HS, SPC7011F (PFC), SQD3011K microcircuits and power switches of the STF13NM60 type.
MainBoard - the main board (motherboard) is a BN41-01958B module, using chips SEMS30, WT61P807, K4B2G1646E, KLM4G1FE3B, 25Q40, 25Q40, WT61P807, TAS5745 and others.
The tuner BN40-00262B CT2CX-3S / K3S provides the reception of television programs and tuning to channels.