
SAMSUNG LED
Model: UE48H5000 UE48H5000AK
Chassis / Version: TS01
Panel: CY-GH048CSLV1V
LED backlight: SAMSUNG 2014SVS48F 3228 L06 REV1.0 131119
T-CON: BN41-02111A BN97-07971A
LED driver (backlight): integrated into PSU
Power Supply (PSU): BN44-00699A L42SF_ESM
MainBoard: BN41-02098B BN94-07140R
Tuner: BN40-00288A DHTQ403IH286A
Control: IR: BN41-02150a
Technical Specifications UE48H5000
SAMSUNG UE48H5000
General repair guidelines for TV LCD LED
Possible malfunctions
- SAMSUNG UE48H5000 TV does not turn on, does not respond to the remote control and control panel buttons, indicators do not light up and do not blink.
With such manifestations, the BN44-00699A power module usually fails. It is necessary to measure its output supply voltages, and in case of their absence, check the operability of the power switches of the converters and rectifier diodes for the probability of breakdown in PN semiconductor junctions.
In case of any breakdowns in the secondary circuits, the converter can operate in emergency short circuit mode, and during short circuit in the power elements of the primary circuit, the mains fuse or the current sensor at the source of the key more often breaks.
Mos-Fet power switches, used in switching power supplies, sometimes fail due to a malfunction of any other elements that can put it out of operation in key mode or create an excess of the maximum permissible parameters of the switch. These can be elements supplying the PWM controller, frequency-setting or damping circuits, or negative feedback elements in the stabilization circuit. PWM controllers, in the absence of visible damage or explicit short-circuit between the terminals, are checked by replacing with new ones, or obviously working.
- There is no image, there is sound, there is a reaction to the remote control. Or immediately after turning on for a second, the image may appear and immediately disappear.
Failure in most such cases is detected in the nodes and backlight elements of the LED panel. The reason for this may be a break in the LED circuit, or a problem in stabilizing their power supply.
To detect a break in the LED lines without disassembling the panel, a current source is required. It is impossible to open transitions connected in series with a simple multimeter; voltage of several tens of volts is necessary.
- The TV does not enter the operating mode, does not respond to the remote control. The indicator on the front panel lights constantly or blinks.
Repair or diagnostics of the BN41-02098B motherboard should begin by checking the stabilizers and power converters needed to power the chips and matrix. If necessary, update or replace the software (software).
If there is no reception of television channels, but the TV is working properly from external devices, first of all, check the voltage of the tuner BN40-00288A DHTQ403IH286A and update the software. The pulses from the I2C bus must be controlled with an oscilloscope.
Attention to users! Self-repair of a SAMSUNG UE48H5000 TV without the appropriate qualifications and necessary experience can lead to its complete non-repairability!

BN41-02098B
BN41-02098B can be used in TVs:
SAMSUNG UE32H4270AU UE32H4270 (Panel HH032AGH-R1), SAMSUNG LT24D310ES (Panel V236BJ1-LE2), SAMSUNG UE40H5000AK (Panel CY-GH040BGLV1V), SAMSUNG UE48H5270AU UE48H5270 (Panel CY-GH048BGLV1V), SAMSUNG UE32H4290AU UE32H4290 (Panel HH032AGH-R2), SAMSUNG UE40H5290AU UE40H5290 (Panel CY-GH040BGLV1V), SAMSUNG UE40J5000AU UE40J5000 (Panel CY-JJ040BGNV2V), SAMSUNG UE40H5020 UE40H5020AK (Panel CY-GH040BGSV1V), SAMSUNG UE40J5100AU (Panel CY-GH040BGSR1V), SAMSUNG T31D310EW (Panel CY-HH032AGSV1H), SAMSUNG UE48J5000AU (Panel CY-JJ048BGEV5V), SAMSUNG UE32H5020AK (Panel CY-GH032BGLV4V), SAMSUNG UE40J5120AU (Panel CY-GH040BGSV1V), SAMSUNG LT32E310EX T32E310EX (Panel CY-GJ032BGEV1V), SAMSUNG UE40H5270 UE40H5270AU (Panel CY-GH048BGLV1V), SAMSUNG UE32J5100AK UE32J5100 (Panel CY-GH032BGSV1V), SAMSUNG UE32H5000AK UE32H5000 (Panel CY-GH032BGLV1V), SAMSUNG UE48H5000 UE48H5000AK (Panel CY-GH048CSLV1V), SAMSUNG UE32J5120AK UE32J5120 (Panel CY-GH032BGSV1V).
Main features of the SAMSUNG UE48H5000 device:
Installed matrix (LED panel) CY-GH048CSLV1V.
The matrix control uses the Timing Controller (T-CON) BN41-02111A.
To power the backlight LEDs, a converter is used, combined with a power supply.
The formation of the necessary supply voltages for all nodes of the SAMSUNG UE48H5000 TV is carried out by the power module , or its analogues.
MainBoard - the main board (motherboard) is a BN41-02098B module.
Tuner BN40-00288A DHTQ403IH286A provides the reception of television programs and tuning to channels.