
SAMSUNG LED
Model: UE48J6330
Chassis / Version: US02
Panel: CY-GH048CSLV7V
LED backlight: D4GE-480DCA-R3, D4GE-480DCB-R3, BN41-02176A, A30418A (BN96-30418A).
T-CON: BN97-10104A BN41-02110A (BN95-01319J BN95-02374A)
LED driver (backlight): integrated into PSU
PWM LED driver: 7014X
MOSFET LED driver: KF3N40W, 5N40
Power Supply (PSU): BN44-00703G L48S1_ESM
PWM Power: S3051 (PFC), FA6A20
MOSFET Power: 14NM50N, 13N60M2
MainBoard: BN41-02353B BN94-09097D
IC MainBoard: CPU: SDP1415, EMMC: THGBMBG5D1KBAIT, RAM: K4B4G16460-BCMA
Tuner: BN40-00318B
Control: Remote: RMCTPJ1AP2, WIFI: WIDT30Q BN59-01174D
Technical Specifications UE48J6330AU
SAMSUNG UE48J6330
General repair guidelines for TV LCD LED
Possible manifestations of defects
- SAMSUNG UE48J6330 does not turn on and does not show any signs of performance at all. Does not blink indicators and does not respond to control buttons.
Most often, with such manifestations, the main power module BN44-00703G is found to be faulty. It is necessary to measure its output voltages, and in case of their absence (full or partial), it is necessary to check the serviceability of power switches (14NM50N, 13N60M2) of converters and rectifier diodes for the presence of a possible short circuit.
In case of any breakdown of semiconductors in the secondary circuits, the converter can usually work normally in emergency short circuit mode. There are no output voltages. And with a short circuit in the power elements of the primary circuit, as a rule, the mains fuse breaks and less often the current sensor at the source of the key.
Mos-Fet keys used in switching power supplies usually fail due to a malfunction of other elements that can put it out of operation in key mode or provoke the excess of maximum current or voltage values. These can be circuits supplying the PWM controller, damping or frequency-setting circuits, or elements of OOS (negative feedback) in the stabilization circuit. PWM controllers (PWM) S3051 (PFC), FA6A20, in the absence of external damage and short circuit between the terminals, are checked by replacing with obviously good ones.
- There is no image, there is sound, it responds to the remote control. Or the image may appear for a second when turned on and immediately disappears.
In such cases, the most likely malfunction of the LED backlight elements. The reason can be both in the power of the LEDs, in their serviceability (breakdown or breakage), as well as in the violation of the contact connections of the LED strips.
It is impossible to check the LED line for breaks without disassembling the panel with a multimeter or tester. For these purposes, it is necessary to open all series-connected PN junctions and a voltage of the order of tens of volts will be required, and ideally, a current source. Having disassembled the panel, it is necessary to check each LED separately. Chinese multimeters, as a rule, light up a single 3-volt LED in the forward direction. In the case of using dual 6-volt LEDs, the PN junction of its protective zener diode can serve as a health indicator. In faulty LEDs, the zener diode will either be cut off or broken into short-circuit.
- The indicator on the front panel blinks, the TV does not turn on in the operating mode, it does not respond to the remote control.
Repair or diagnostics of the BN41-02353B motherboard should begin by checking the stabilizers and power converters needed to power the chips and matrix. If necessary, update or replace the software (software). When repairing an MB board, you need to check its CPU components: SDP1415, EMMC: THGBMBG5D1KBAIT, RAM: K4B4G16460-BCMA. Defective items should be replaced. If chips with BGA soldering technology are used, a problem in its implementation is detected by the local heating of the chip.
In the absence of tuning to the channels of on-air or cable television, you should make sure that the software is correct, as well as in accordance with the ratings of the supply voltage at the terminals of the tuner BN40-00318B. It is also necessary to check the presence of pulses of data exchange between the tuner and the processor via the I2C bus using an oscilloscope.
Attention TV owners! Attempts at self-repair of SAMSUNG UE48J6330 are not recommended by the manufacturer and can lead to serious negative consequences!

BN41-02353B
BN41-02353B can be used in TVs:
SAMSUNG UE40J6390 (Panel CY-GH040CSLV1V), SAMSUNG UE40J5530AU UE40J5530 (Panel CY-GJ040BGSV5V), SAMSUNG UE40J5500AU (Panel CY-GJ040BGSV5V), SAMSUNG UE40J5550 UE40J5550AU (Panel CY-GJ040BGSV1V), SAMSUNG UE40J6330AU (Panel CY-GH040CSLVFV), SAMSUNG UE32J6300 UE32J6300AU (Panel CY-GH032CSLV5V), SAMSUNG UE48J6200AU (Panel CY-GH048CSLVAV), SAMSUNG UE48J5510AU (Panel CY-GJ048BGLV3V), SAMSUNG UE32J6500AU UE32J6500 (Panel CY-WJ032CGLV2V), SAMSUNG UE40J5520AU UE40J5520 (Panel CY-GJ040BGSV5V), SAMSUNG UE43J5500 UE43J5500AU (Panel T430HVF01.0), SAMSUNG UE40J6200AU UE40J6200 (Panel CY-GH040CSLV8V), SAMSUNG UE32J5550AU UE32J5550 (Panel CY-GJ032BGAB3V), SAMSUNG UE32J5500AU (Panel T320HVF05.5), SAMSUNG UE40J6590 UE40J6590AU (Panel CY-WJ040CGLV1V), SAMSUNG UE40J5510AU (Panel CY-GJ040BGSV3V).
The appearance of the power supply
Main features of the SAMSUNG UE48J6330 device:
Installed matrix (LED panel) CY-GH048CSLV7V.
The matrix control uses the Timing Controller (T-CON) BN97-10104A.
To power the backlight LEDs, a converter is used, combined with a power supply, controlled by a 7014X PWM controller. As the power elements of the LED driver, keys of the type KF3N40W, 5N40 are used.
The necessary supply voltages for all nodes of the SAMSUNG UE48J6330 TV are generated by the BN44-00703G power supply module or its analogs using S3051 (PFC), FA6A20 microchips and 14NM50N, 13N60M2 type power switches.
MainBoard - the main board (motherboard) is a BN41-02353B module, using CPU chips: SDP1415, EMMC: THGBMBG5D1KBAIT, RAM: K4B4G16460-BCMA and others.
The tuner BN40-00318B provides the reception of television programs and tuning to channels.