![](https://4.bp.blogspot.com/-ODaEZZr8B_k/XiXUIOtI3xI/AAAAAAAAobA/W8fLTD0TcPMGBSXoTcpp4Oewm7cyBbDJwCK4BGAYYCw/s200/UE49K5100AU.jpg)
SAMSUNG LED
Model: UE49K5100AU
Panel: CY-FK049BNHV1V
T-CON: TT4851B01-1-C-3
LED driver (backlight): integrated into PSU; 740mA
Power Supply (PSU): BN44-00868A L55PF_KDY
MainBoard: BN41-02527A BN94-10854S
IC MainBoard: CPU: SENK 17, EEPROM: 24C256, NAND Flash: F59L1G81MA-25TI, SPI Flash: 25Q40CLSIP
Tuner: BN40-00323B
Control: IR: BN41-02515A REV 1.1
Technical Specifications UE49K5100AU
SAMSUNG UE49K5100AU
General repair guidelines for TV LCD LED
Possible malfunctions
- SAMSUNG UE49K5100AU TV does not turn on. There are no signs of operability. The indicators on the front panel do not light or flash, the TV does not respond to the remote control and control buttons.
Failure in such cases should begin to be sought in the power supply circuits BN44-00868A. Then it is necessary to measure its output voltages and, in case of their complete or partial absence, it is necessary to check the serviceability of power switches and rectifier diodes of the converters for a possible short circuit.
In case of breakdowns in the secondary circuits, the converter can operate in a short circuit mode, and during a short circuit in the elements of the primary circuit, the mains fuse usually breaks.
Mos-Fet keys used in switching power supplies usually fail due to a malfunction of other elements that can put it out of operation in key mode or provoke the excess of maximum current or voltage values. These can be circuits supplying the PWM controller, damping or frequency-setting circuits, or elements of OOS (negative feedback) in the stabilization circuit. PWM controllers (PWM), in the absence of external damage and short circuit between the terminals, are checked by replacing with obviously good ones.
- There is no image, there is sound, it responds to the remote control. Or the image may appear for a second when turned on and immediately disappears.
In such cases, the most likely malfunction of the LED backlight elements. The reason can be both in the power of the LEDs, in their serviceability (breakdown or breakage), as well as in the violation of the contact connections of the LED strips.
It should be remembered that it is not possible to determine the break in the LED lines without disassembling the panels using a tester or multimeter without an additional device, for example, a current source. To open all PN junctions connected in series at once, a voltage of several tens of volts may be required. Then it is necessary to open the panel and check each LED separately with a multimeter. If the capabilities of your multimeter do not allow you to open the LED in the forward direction or dual LEd are used, then the PN junction of the emergency zener diode can indirectly serve as a health indicator. In case of LED-a failure, the zener diode PN junction will either be cut off or broken into short-circuit.
- The TV does not turn on, the indicator indicates standby or operating mode, or blinks.
Repair or diagnostics of the BN41-02527A motherboard should begin by checking the stabilizers and power converters needed to power the chips and matrix. If necessary, update or replace the software (software).
If there is no reception of television channels, but the TV works properly from external devices, first of all, check the voltage of the tuner BN40-00323B and update the software. The pulses from the I2C bus must be controlled with an oscilloscope.
Attention to users! Self-repair of a SAMSUNG UE49K5100AU TV without the appropriate qualifications and necessary experience can lead to its complete non-repairability!
![](https://1.bp.blogspot.com/-SX3r6Z8OvIo/XiXUBWl04WI/AAAAAAAAoa4/P5eAD4LrzIQg7bXI_HiyMOwBW28K2NexgCK4BGAYYCw/s320/BN41-02527A_DCE.jpg)
![](https://4.bp.blogspot.com/-NFbsaV6M6UE/XiXUBXBXGSI/AAAAAAAAoa0/AMroy9Ls8BkbrWQmRxW7OV-CKBtMIVSVgCK4BGAYYCw/s320/BN44-00868A_DCE.jpg)
BN41-02527A
The appearance of the power supply
Main features of the SAMSUNG UE49K5100AU device:
Installed matrix (LED panel) CY-FK049BNHV1V.
The matrix control uses the Timing Controller (T-CON) TT4851B01-1-C-3.
To power the backlight LEDs, a converter is used, combined with a power supply.
The formation of the necessary supply voltages for all nodes of the SAMSUNG UE49K5100AU TV is carried out by the power module BN44-00868A, or its analogues.
MainBoard - the main board (motherboard) is a BN41-02527A module, using CPU chips: SENK 17, EEPROM: 24C256, NAND Flash: F59L1G81MA-25TI, SPI Flash: 25Q40CLSIP and others.
The tuner BN40-00323B provides the reception of television programs and tuning to channels.