
SAMSUNG LED
Model: UE49KU6300
Panel: CY-WK049HGLV1V
LED backlight: LM41-00334A, LM41-00335A
LED driver (backlight): integrated into PSU
Power Supply (PSU): BN44-00807A L55S6_FHD REV: 1.1 HU10738-14004
MainBoard: BN41-02528A BN94-10826L
IC MainBoard: SDP1531, K4F8E304HBMGCH, 25Q40CLSIP, 25Q80DVSIG, S24C512C
Tuner: BN40-00323A
Control: IR: A39955B, WiFi: BN59-01174D WIDT30Q
Technical Specifications UE49KU6300U
SAMSUNG UE49KU6300
General repair guidelines for TV LCD LED
Possible malfunctions
- SAMSUNG UE49KU6300 does not turn on and does not show any signs of performance at all. Does not blink indicators and does not respond to control buttons.
In some of these cases, a fault is detected in the BN44-00807A power supply module. It is necessary to measure its output voltages and, in case of their absence, check the serviceability of power switches and rectifier diodes in the converters for possible breakdown.
In case of any breakdown of semiconductors in the secondary circuits, the converter can usually work normally in emergency short circuit mode. There are no output voltages. And with a short circuit in the power elements of the primary circuit, as a rule, the mains fuse breaks and less often the current sensor at the source of the key.
Mos-Fet power switches, used in switching power supplies, sometimes fail due to a malfunction of any other elements that can put it out of operation in key mode or create an excess of the maximum permissible parameters of the switch. These can be elements supplying the PWM controller, frequency-setting or damping circuits, or negative feedback elements in the stabilization circuit. PWM controllers, in the absence of visible damage or frank short-circuit between the terminals, are checked by replacing with new, or obviously working.
- There is no image, but there is sound and reaction to the remote control. Or for a second, the image may appear immediately after switching on.
As a rule, in such cases there is no display backlight. The reason for this may be a break in the LED circuit, or a problem in stabilizing their power supply.
To detect a break in the LED lines without disassembling the panel, a current source is required. It is impossible to open transitions connected in series with a simple multimeter; voltage of several tens of volts is necessary.
- The indicator on the front panel blinks, the TV does not turn on in the operating mode, it does not respond to the remote control.
Repair or diagnostics of the BN41-02528A motherboard should begin by checking the stabilizers and power converters needed to power the chips and matrix. If necessary, update or replace the software (software). If it is not possible to replace the MB board (SSB), you need to check the health of its elements - SDP1531, K4F8E304HBMGCH, 25Q40CLSIP, 25Q80DVSIG, S24C512C. Defective components should be replaced.
Before replacing the tuner BN40-00323A, if there is no tuning to the channels, you must first check the software and the supply voltage at its terminals. It is also necessary to make sure that the tuner and processor can exchange data via the I2C bus
Attention TV owners! Attempts to self-repair SAMSUNG UE49KU6300 are not recommended by the manufacturer and can lead to serious negative consequences!

BN41-02528A
BN41-02528A can be used in TVs:
SAMSUNG UE43KU6650U (Panel CY-VK043HGAV5V), SAMSUNG UE43KU6000W UE43KU6000 (Panel CY-GK043HGEV1H), SAMSUNG UE55KU6400 UE55KU6400U (Panel CY-KK055HQLV4H), SAMSUNG UE49KU6670 UE49KU6670U (Panel CY-VK049HGLV4V), SAMSUNG UE40KU6000U (Panel LSF400FN05-L03 CY-GK040HGLV4V), SAMSUNG UE40KU6300U (Panel CY-WK040HGLV1V), SAMSUNG UE43KU6500U (Panel CY-VK043HGAV4V T430QVR01.0), SAMSUNG UE40KU6402U (Panel CY-KK040HGNV4H).
The appearance of the power supply
Main features of the SAMSUNG UE49KU6300 device:
Installed matrix (LED-panel) CY-WK049HGLV1V.
To power the backlight LEDs, a converter is used, combined with a power supply.
The formation of the necessary supply voltages for all nodes of the SAMSUNG UE49KU6300 TV is carried out by the power module BN44-00807A, or its analogues.
MainBoard - the main board (motherboard) is a BN41-02528A module, using microchips SDP1531, K4F8E304HBMGCH, 25Q40CLSIP, 25Q80DVSIG, S24C512C and others.
The tuner BN40-00323A provides the reception of television programs and tuning to channels.