![](https://blogger.googleusercontent.com/img/b/R29vZ2xl/AVvXsEifIORS2fG7epjxUjWup6IHYpbXiB0oCs1qduTbEgUTDOvVT__ilN4KY2aLIiHEjO849Ky1nXC4YdVWrwZ2R7yhNurgDAz5XNv2Gg3w7Ia2JV5hIG0qY-9xmdNGB2fe0KxqXPmMNgP3foQ/s200/UE55KU6510U.jpg)
SAMSUNG LED
Model: UE55KU6510U UE55KU6510
Chassis / Version: FD04
Panel: CY-VK055HGLV8V
LED driver (backlight): integrated into PSU
Power Supply (PSU): BN44-00876C REV1.1 PSLF171S08A
PWM Power: PFC, PWM
MOSFET Power: 60S600CE
MainBoard: BN41-02528A BN94-10785V
IC MainBoard: SDP1531, K4F8E304HBMGCH, 25Q80DVSIG, 25Q40CLSIP, S24C512C
Tuner: BN40-00323A
Technical Specifications UE55KU6510U
SAMSUNG UE55KU6510U
General repair guidelines for TV LCD LED
Possible malfunctions
- SAMSUNG UE55KU6510U does not turn on, does not respond to buttons and remote control, indicators on the front panel do not light up and do not blink.
With such manifestations, a malfunction is likely to be detected in the BN44-00876C power supply module. It is then necessary to measure its output voltages and, if they are absent, you should check the power switches (60S600CE) and the rectifier diodes of the converters for a short circuit probability.
In case of breakdowns of semiconductors in secondary circuits, the converter can usually operate abnormally in short circuit mode, and during short circuit in the power elements of the primary circuit, the main fuse often breaks.
Mos-Fet power switches, used in switching power supplies, sometimes fail due to a malfunction of any other elements that can put it out of operation in key mode or create an excess of the maximum permissible parameters of the switch. These can be elements supplying the PWM controller, frequency-setting or damping circuits, or negative feedback elements in the stabilization circuit. PFC, PWM PWM controllers, in the absence of visible damage or explicit short-circuit between the terminals, are checked by replacing with new ones, or obviously working.
- There is no image, there is sound, all other functions of the TV work. When turned on, the image may sometimes appear for a second.
Often in such cases, there is no LED backlight. The reason can be found in the malfunction of the LEDs, in the violation of the contact connections of the LED strips, or in the provision of their power (LED-driver).
It should be remembered that it is not possible to determine the open circuit in the LED lines without disassembling the panels with a tester or multimeter without an additional device, for example, a current source. To open all PN junctions connected in series at once, a voltage of several tens of volts may be required. Then it is necessary to open the panel and check each LED separately with a multimeter. If the capabilities of your multimeter do not allow you to open the LED in the forward direction or dual LEd are used, then the PN junction of the emergency zener diode can indirectly serve as a health indicator. In case of LED-a failure, the zener diode PN junction will either be cut off or broken into short-circuit.
- The TV does not turn on, does not respond to the remote control. The indicator blinks or signals standby mode.
Repair or diagnostics of the BN41-02528A motherboard should begin by checking the stabilizers and power converters needed to power the chips and matrix. If necessary, update or replace the software (software). Often, the MB (SSB) card must be replaced in case of complex malfunctions that are difficult to detect. When trying to repair, you should check its elements - SDP1531, K4F8E304HBMGCH, 25Q80DVSIG, 25Q40CLSIP, S24C512C and replace failed chips with new ones. Some malfunctions may be due to the use of BGA soldering technologies in modern Main Board technologies. Typically, such defects are detected by local heating of the chip.
The malfunction of the tuner BN40-00323A is established after checking the software and all supply voltages at its terminals. The data exchange of the tuner with the processor via the I2C bus can be controlled by an oscilloscope.
Attention TV owners! Attempts to self-repair SAMSUNG UE55KU6510U are not recommended by the manufacturer and can lead to serious negative consequences!
![](https://blogger.googleusercontent.com/img/b/R29vZ2xl/AVvXsEgHAa5S4vxjrrdBhuI0p_jSGtdFgAOLUvedpGoWVkQ3385V0YkxMp-5a_7rFeLcPVUIpycLjKTL72B0ctqZB5uTToSh8OKV5uH3p4owOVFMBy6dsTazuJ88LZFxcjA7aOvRfPJO908le1Q/s320/BN44-00876C_DCE.jpg)
BN41-02528A
BN41-02528A can be used in TVs:
SAMSUNG UE43KU6650U (Panel CY-VK043HGAV5V), SAMSUNG UE43KU6000W UE43KU6000 (Panel CY-GK043HGEV1H), SAMSUNG UE55KU6400 UE55KU6400U (Panel CY-KK055HQLV4H), SAMSUNG UE49KU6670 UE49KU6670U (Panel CY-VK049HGLV4V), SAMSUNG UE40KU6000U (Panel LSF400FN05-L03 CY-GK040HGLV4V), SAMSUNG UE40KU6300U (Panel CY-WK040HGLV1V), SAMSUNG UE43KU6500U (Panel CY-VK043HGAV4V T430QVR01.0), SAMSUNG UE40KU6402U (Panel CY-KK040HGNV4H).
The appearance of the power supply
Main features of the SAMSUNG UE55KU6510U device:
Installed matrix (LED panel) CY-VK055HGLV8V.
To power the backlight LEDs, a converter is used, combined with a power supply.
The necessary supply voltages for all nodes of the SAMSUNG UE55KU6510U TV are generated by the BN44-00876C power supply module or its analogs using PFC, PWM microcircuits, and 60S600CE type power switches.
MainBoard - the main board (motherboard) is a BN41-02528A module, using microchips SDP1531, K4F8E304HBMGCH, 25Q80DVSIG, 25Q40CLSIP, S24C512C and others.
The tuner BN40-00323A provides the reception of television programs and tuning to channels.