Technical description and composition of the DAEWOO L32S65FVBE TV, panel type and applicable modules. The composition of the modules.DAEWOO LED
Model: L32S65FVBE
Chassis / Version: TP.S512.PB83
Panel: BOEI320WU1
LED backlight: GC32D07-ZC21FG-15 303GC320038
T-CON: 47-6021049 HV320FHB-N00
LED driver (backlight): integrated into MainBoard
PWM LED driver: SN510P
MOSFET LED driver: AOD4454
Power Supply (PSU): integrated into MainBoard
PWM Power: PWM SOT23-6
MainBoard: TP.S512.PB83
IC MainBoard: CPU: S2T512, SPI Flash: 25Q64, Sound: TPA3110LD
Tuner: XF-3SDT-H (R840)
Control: IR: 22025B8100P / T
Technical Specifications L32S65FVBE
DAEWOO L32S65FVBE
General repair guidelines for TV LCD LED
Possible malfunctions
- The DAEWOO L32S65FVBE TV does not turn on, does not respond to the remote control and the control panel buttons, does not light up or blink indicators.
In such cases, the main power source - the AC / DC voltage converter, which is combined with the MainBoard TP.S512.PB83 board, may turn out to be faulty. It is necessary to measure its output voltages, and in case of their absence, check the operability of the power switches of the converters and rectifier diodes for the probability of a short circuit.
In case of any breakdown of semiconductors in the secondary circuits, the converter can usually work normally in emergency short circuit mode. There are no output voltages. And with a short circuit in the power elements of the primary circuit, as a rule, the mains fuse breaks and less often the current sensor at the source of the key.
Breakdown of power switches (MosFet) in pulsed sources is sometimes caused by malfunctions of other circuit elements, for example, in circuits supplying a PWM controller, frequency-setting or damper ones, as well as in negative feedback circuits (OOS) of stabilization. PWM controllers (PWM) PWM SOT23-6, if they do not have visible damage to the case and open short circuit between the terminals, are usually checked by replacement.
- There is no image, there is sound, it is responding to the remote control. Or immediately after turning on for a second, the image may appear and immediately disappear.
Often in such cases, there is no LED backlight. The reason can be both in the power supply of the LEDs, in their serviceability (breakdown or breakage), as well as in the violation of the contact connections of the LED strips.
To detect a break in the LED lines without disassembling the panel, a current source is required. It is impossible to open transitions connected in series with a simple multimeter; voltage of several tens of volts is necessary.
- The TV does not enter the operating mode, does not respond to the remote control. The indicator on the front panel lights constantly or blinks.
Repair or diagnostics of the TP.S512.PB83 motherboard should begin by checking the stabilizers and power converters needed to power the microcircuits and matrix. If necessary, update or replace the software (software). In some cases, to repair the MB (SSB) board, it may be necessary to replace the chips - CPU: S2T512, SPI Flash: 25Q64, Sound: TPA3110LD with new or obviously working ones. In cases where BGA technologies are used, defects are usually localized by the heating method.
If the TV works normally from external devices, but does not tune into television channels, the tuner XF-3SDT-H (R840) may be malfunctioning. In such cases, first of all, you should make sure that there are supply voltages at its corresponding conclusions. It is also necessary to make sure that the tuner and processor can exchange data via the I2C bus. Sometimes the cause of the inoperability of the tuner may be a software failure.
It should be remembered! Attempts to independently repair the DAEWOO L32S65FVBE TV, in the absence of the necessary qualifications and experience, are categorically not recommended and are fraught with negative consequences, up to the complete non-repairability of the device!
SCHEMATIC DIAGRAM / SERVICE MANUAL ------------------> MainBoard TP.S512.PB83
The appearance of MainBoard TP.S512.PB83 is shown in the figure below:
TP.S512.PB83
TP.S512.PB83 can be used in TVs:
AKAI LEA-39V51P (Panel LC390TA2A 902-P05-390H ), DEXP 40A7000 (Panel C400F13-E2-C), DEXP F39B7100E (Panel T390HVN04.0 CX390DLEDM), DEXP H32B7000C (Panel T320XVN02.9 C320X14-E2-A), DEXP F42B7000ED (Panel CX420DLEDM), DEXP F32C7000B (Panel BOEI320WU1), DEXP F32C7100B/W F32C7100 (Panel BOEI320WU1), DEXP 32A7000 (Panel BOEI320WU1), DEXP 42A7000 (Panel CX420DLEDM), DEXP F32B7000B (Panel BOEI320WU1), DEXP H39D7000E (Panel CX390DLEDM), DEXP F40B7000C (Panel C400F13-E2-C), DEXP H32B3200CD (Panel HV320WX2-201), HAIER LE28F6000T (Panel A275HD1A01-2 / LVW280CSDO E2 V2), HAIER LE32F6000T (Panel ST3151A05-8 LVW320CSDX E13 V2), MYSTERY MTV-4025LT2 (Panel CX400DLEDM), SHIVAKI STV-32LED13 (Panel SV320SHD PDL320TU2A X41), SHIVAKI STV-42LED16 (Panel V420HJ-P01), SHIVAKI STV-32LED14 (Panel CX315DLEDM AJ32TO3), SHIVAKI STV-40LED13W (Panel V400HJ6PE1-C2), SHIVAKI STV-32LED15 (Panel HV320WHB-N80), SUPRA STV-LC32T440WL (Panel C320X14-E13-H), SUPRA STV-LC32T900WL (Panel LC320TU3A), SUPRA STV-LC40T900FL (Panel 1080p Full HD 1920x1080), THOMSON T32D15DH-01B (Panel LVW320CSDX E13 V30), THOMSON T28D15DH-01B (Panel LVW280CSDE E3 V5), THOMSON T32D16DH-01W T32D16DH (Panel LVW320CSDX E19 V28), THOMSON T43D16SF-01B T43D16SF (Panel LVF430LGDO E2 V18).
Main features of the device DAEWOO L32S65FVBE:
Installed matrix (LED-panel) BOEI320WU1.
The matrix control uses the Timing Controller (T-CON) 47-6021049.
To power the backlight LEDs, a converter is used, combined with the TP.S512.PB83 main board, controlled by the SN510P PWM controller. As power elements of the LED driver, keys of the AOD4454 type are used.
The power module is combined with the MainBoard and is made according to the flyback AC / DC voltage converter circuit using PWM SOT23-6 microcircuits.
MainBoard - the main board (motherboard) is a TP.S512.PB83 module, using CPU chips: S2T512, SPI Flash: 25Q64, Sound: TPA3110LD and others.
Tuner XF-3SDT-H (R840) provides the reception of television programs and tuning to channels.
