DAEWOO LED
Model: L32T670VGE
Chassis / Version: TP.MS3463S.PB801
Panel: CN32XB720
LED backlight: CRH-K323030T020665R
T-CON: LSC320AN09-H02
LED driver (backlight): integrated into MainBoard
PWM LED driver: SN51DP
MOSFET LED driver: PA110BDA
Power Supply (PSU): integrated into MainBoard
PWM Power: PWM SOT23-6
MainBoard: TP.MS3463S.PB801
IC MainBoard: CPU: MSD3463GU, SPI Flash: 25Q64, AUDIO: OB6220VP
Tuner: R840
Control: IR: XBT70049A3 KR
Technical Specifications L32T670VGE
DAEWOO L32T670VGE
General repair guidelines for TV LCD LED
Possible malfunctions
- DAEWOO L32T670VGE does not turn on, the indicators on the front panel do not light or flash. The TV does not respond to the control buttons and the remote control.
The malfunction in such cases, first of all, should be sought in the power elements of a switching power supply (IIP) - a network voltage converter (AC / DC), which in this TV model is combined with the MainBoard TP.MS3463S.PB801 main board. It is necessary to measure its secondary output voltages, and if they are absent, check the power switches and rectifier diodes in the converters for a short circuit.
In case of breakdowns of semiconductors in the secondary circuits, the converter can usually work abnormally in the short circuit mode, and during short circuit in the power elements of the primary circuit, the mains fuse often breaks.
Mos-Fet keys used in switching power supplies usually fail due to a malfunction of other elements that can put it out of operation in key mode or provoke an excess of the maximum current or voltage. These can be circuits supplying the PWM controller, damping or frequency-setting circuits, or elements of OOS (negative feedback) in the stabilization circuit. PWM controllers (PWM) PWM SOT23-6, in the absence of external damage and short circuit between the terminals, are checked by replacing with obviously good ones.
- There is no image, but there is sound and reaction to commands from the remote control. Or the image appears immediately after turning on and disappears.
A malfunction is usually most likely in these cases at the backlight nodes of the display matrix. The reason for this may be a break in the LED circuit, or a problem in stabilizing their power supply.
To check the health in the LED circuit, it is better to use a current source with a maximum voltage of 200V. We do not recommend using any voltage sources for this purpose. You can check each LED individually with a simple Chinese multimeter (powered by 9 volts) in the P-N-junction test mode. If you connect the red probe of the multimeter to the anode of the LED, and the black to its cathode, then the 3-volt LED will light up slightly, and in the opposite direction you can detect the transition of the emergency zener diode. A zener diode PN junction indirectly indicates a LED-a
- The TV does not turn on, does not respond to the remote control. The indicator blinks or signals standby mode.
Repair or diagnostics of the TP.MS3463S.PB801 motherboard should begin by checking the stabilizers and power converters needed to power the chips and matrix. If necessary, update or replace the software (software). When repairing an MB board, you need to check its CPU components: MSD3463GU, SPI Flash: 25Q64, AUDIO: OB6220VP. Defective items should be replaced. If chips with BGA soldering technology are used, a problem in its implementation is detected by the local heating of the chip.
The malfunction of the R840 tuner is established after checking the software and all the supply voltages at its terminals. The data exchange of the tuner with the processor via the I2C bus can be controlled by an oscilloscope.
It should be remembered! Attempts to self-repair a TV DAEWOO L32T670VGE, in the absence of the necessary qualifications and experience, are categorically not recommended and are fraught with negative consequences, up to the complete non-repairability of the device!
SCHEMATIC DIAGRAM / SERVICE MANUAL ------------------> Trouble Shooting Chassis TP.MS3463S.PB801
The appearance of MainBoard TP.MS3463S.PB801 is shown in the figure below:
TP.MS3463S.PB801
TP.MS3463S.PB801 can be used in TVs:
AKAI LEA-40V35M (Panel LSC400HM06), AKIRA 32LED38T2P (Panel ST3151A05-8), AKIRA 32LED02T2M (Panel ST3151A04-9 Ver.2.1), BBK 32LEM-1029/TS2C (Panel C320X16-E18-H), BBK 39LEM-1033/TS2C (Panel C390X15-E8-A G01), BBK 32LEM-1026/TS2C (Panel CX315DLEDM ST3151A05-8), BBK 32LEM-1027/TS2C (Panel ST3151A05-8 / CX315DLEDM), DEXP F43C7100K (Panel LC430DUY (SH)(A1)), DEXP F42B7000M (Panel V420HJ2-P01), DEXP F43C7000C (Panel C430F14-E1-L / LC430DUY), DEXP F40B7100K (Panel LSC400HN02-G02 40N06-L-HPX1F1), DEXP H28C7100C (Panel C275X15-E1-H (G31)), DEXP H32C7300K (Panel LSC320AN02), DEXP H32D7100C (Panel ST3151A05-8 Ver2.5), DEXP H28D7300K (Panel HV280WX2-260), ERISSON 32LES78T2W (Panel KM0320LDRH0037), ERISSON 32LEE30T2 (Panel LK315T3HB87-12V), SUPRA STV-LC32T560WL (Panel LSC320AN10), SUPRA STV-LC32T550WL (Panel LSC320AN02), SUPRA STV-LC40T500WL (Panel C39X15-E7-A), TELEFUNKEN TF-LED32S45T2 (Panel LK315T3HB87-12V), THOMSON T39D20DH-01B (Panel T390XVN01.0).
Main features of the DAEWOO L32T670VGE device:
Installed matrix (LED panel) CN32XB720.
The matrix control uses the Timing Controller (T-CON) LSC320AN09-H02.
To power the backlight LEDs, a converter is used, combined with the TP.MS3463S.PB801 main board, controlled by the SN51DP PWM controller. As the power elements of the LED driver, keys of the type PA110BDA are used.
The power module is combined with the MainBoard and is made according to the flyback AC / DC voltage converter circuit using PWM SOT23-6 microcircuits.
MainBoard - the main board (motherboard) is a TP.MS3463S.PB801 module, using CPU chips: MSD3463GU, SPI Flash: 25Q64, AUDIO: OB6220VP and others.
The R840 tuner provides TV reception and channel tuning.
Brand: DAEWOO, Model: L32T670VGE.
Shortly from the TV: LCD, LED backlight, 31.5 ", 1366x768, 720p HD, there is a satellite tuner, sound: 12W, HDMI connectors: 3.
The composition uses MainBoard TP.MS3463S.PB801 and LCD-panel CN32XB720. The power supply is combined with the MainBoard.
Technical description
DAEWOO L32T670VGE LED TV with CN32XB720 LCD display, diagonal size 31.5 "(80 cm) in 16: 9 format. The required screen brightness of 240 cd / m² is provided by LED backlighting. Dynamic contrast ratio of 5,000,000: 1 is achieved by special control of the LEDs. V LCD panels are backlit with Direct LEDs, and HD images can be viewed in 1366x768 pixels in 720p (HD Ready) graphic decomposition standard. Supported media file formats: MP3, WMA, MPEG4, HEVC (H.265), DivX, MKV, JPEG.
The power of the sound system 12 W (2x6 W) provides two speakers. It uses a NICAM stereo signal processing system and Sound Surround.
The external interface (communication with other devices) is supported by standard input and output connectors: antenna input (RF), AV, HDMI x3, USB. An output for connecting headphones is provided. The digital tuner is capable of receiving television channels in the standards DVB-T MPEG4, DVB-C, DVB-T2, DVB-S2.
Overall dimensions: with stand 730x476x207 mm, without stand 730x430x75 mm.
TV mass: without stand: 3.9 kg.
Attention! The CN32XB720 panel of a DAEWOO L32T670VGE LED TV is an expensive and unreliable element.
Avoid any impact on the glass and pressure on the surface of the screen to avoid damage to the LED panel!
It is also unsafe to get liquid on the screen. Sometimes one drop is enough if it flows down the glass onto the cables so that the TV becomes unrepairable.