Technical description and composition of the ERISSON 22LEB15 TV, type of panel and applicable modules. The composition of the modules.ERISSON LED
Model: 22LEB15
Chassis / Version: T.VST29.A2B 12062
Panel: M215HW01
MainBoard: T.VST29.A2B 12062
IC MainBoard: CPU: TSUMV59XU-Z1; SPI Flash: W25Q32;
Tuner: CDT-3SP5i2-36
Specifications 22LEB15
ERISSON 22LEB15
General repair guidelines for TV LCD LED
Repair of electronic equipment usually begins with its external inspection and diagnosis of the malfunction. In this case, you should examine all the internal components of the ERISSON 22LEB15 TV, as well as the external elements of the housing. According to some external signs of a change in the state of some elements, it is sometimes possible to make assumptions about the nature of the defect, as well as determine the further direction of the troubleshooting. Carbonized paint on the upper layer of resistors, electrolytic capacitors of rectifier filters swollen after boiling, cracked soldering at the terminals of heating elements or transformers can often suggest the cause of the defect and possible consequences.
Malfunctions of the power module can be expressed in different ways, for example, ERISSON 22LEB15 does not turn on at all and the control lights on its front panel do not light up and do not blink, there are no signs of operability. It should be noted that with the same external manifestations, the processor power regulator (converter) may be faulty. In the absence of swollen filter capacitors of the secondary rectifiers, the diagnostics of the power supply should be started by checking the fuse and, if it is broken, it is first necessary to check all the power semiconductor elements of the primary circuit - diodes and transistors for the possibility of an avalanche or thermal breakdown.
It should be remembered that in the practice of repair, usually the power switches in switching power supplies (SMPS) do not fail due to their poor quality and, in such cases, it is necessary to look for the cause that led to a malfunction and provoked a breakdown of the key. Most often, the culprits of the accident are dried electrolytic capacitors or dangling resistors in the primary circuit, or the PWM controller chip itself may be faulty. It is also necessary to check all the semiconductor elements of the stabilization circuit in the primary and secondary circuits.
If, when you turn on the TV, the image appears and immediately disappears, or is initially absent when you turn on, but the sound is there and other functions work, there is a high probability of a malfunction of the LED driver (power converter for the backlight LEDs of the M215HW01 panel). In such cases, the general power module is also subject to verification, in which the electrolytic capacitors of the rectifier filter supplying the LED driver should be checked.
To check the health of the LEDs and contact connections in their power circuit, the panel must be disassembled.
It should be remembered that it is not possible to determine the open circuit in the LED lines without disassembling the panels with a tester or multimeter without an additional device, for example, a current source. To open all PN junctions connected in series at once, a voltage of several tens of volts may be required.
When trying to repair the motherboard, you should first check the serviceability of linear stabilizers or power converters of microcircuits and, if necessary, update the software (software).
Board repair and replacement of CPU chips: TSUMV59XU-Z1; SPI Flash: W25Q32; are made in the presence of the necessary equipment, and the corresponding element base. Faults associated with the application of BGA processor soldering technologies can be localized by the heating method.
In cases where there is no tuning to local television channels, make sure that there are supply voltages at the terminals of the tuner CDT-3SP5i2-36.
Once again, we remind TV users: you should not make attempts to repair it yourself without the appropriate knowledge, experience and the necessary qualifications! Trust the repair only to professionals with sufficient experience in the field of electronic equipment repair.
FIRMWARE FOR SPI FLASH -----------> ERISSON 22LEB15 , Main: T.VST29.A2B 12062, Panel: M215HW01
The appearance of MainBoard T.VST29.A2B is shown in the figure below:T.VST29.A2B
T.VST29.A2B can be used in TVs:
DNS E19A00 (Panel CX185LEDM (V185B1-PE)), DNS E22A11 (Panel M215HGE-P02), DNS E22A00 (Panel CX215LEDM M215HGE-P01), DNS E16A20 (Panel TL156WH4 (TL)(N2)), ERISSON 22LEB15 (Panel M215HW01), ERISSON 19LEB15 (Panel M185XW01), ERISSON 24LEB15 (Panel M240HW01 VD), ROLSEN RL-19L1003U (Panel M185BGE-L10 Rev.C1), ROLSEN RL-22L1003U (Panel V216BG1-LE1 REV C1), ROLSEN RL-23L1003UF (Panel M230HGE-L20 Rev.C1), ROLSEN RL-23L1005UF (Panel M230HGE-L20 RevC1).
Main features of the ERISSON 22LEB15 device:
Installed matrix (LED-panel) M215HW01.
The required supply voltage for all nodes of the TV ERISSON 22LEB15 provides a switching power supply.
MainBoard - the main board (motherboard) is a T.VST29.A2B module, using CPU chips: TSUMV59XU-Z1; SPI Flash: W25Q32; and others.
Tuner CDT-3SP5i2-36 provides the reception of television programs and tuning to channels.
Additional technical information about the panel:
Brand: AUO
Model: M215HW01 V2
Type: a-Si TFT-LCD, Panel
Diagonal size: 21.5 inch
Resolution: 1920x1080, FHD
Display Mode: TN, Normally White, Transmissive
Active Area: 476.64x268.11 mm
Surface: Antiglare, Hard coating (3H)
Brightness: 250 cd / m²
Contrast Ratio: 1000: 1
Display Colors: 16.7M (6-bit + Hi-FRC)
Response Time: 3.8 / 1.2 (Tr / Td)
Frequency: 60Hz
Lamp Type: 2 pcs CCFL Without Driver
Signal Interface: LVDS (2 ch, 8-bit), 30 pins
Voltage: 5.0V
Technical description
ERISSON 22LEB15 TV with an M215HW01 LCD display, diagonal size 22 "(56 cm) in 16: 9 format. The required screen brightness of 300 cd / m² is provided by LED backlighting. Contrast, as the ratio of maximum brightness to minimum, is 1000: 1. The LED panel of this TV uses end LED backlighting - Edge LED.The TV’s design and technical features include viewing programs and movies in high quality HD at a resolution of 1920x1080 pixels in a graphic resolution of 1080p (Full HD) standard. the audio or video signal can be processed in analogue systems PAL, SECAM, NTSC. Graphic processing and digital signal generation occurs in the standards 480i, 480p, 576i, 576p, 720p, 1080i, 1080p. Stereo sound is realized by two built-in speakers. The audio processing system NICAM STEREO is used .
The external interface (communication with other devices) is supported by standard input and output connectors: antenna input (RF), AV, S-Video, component, VGA, HDMI x3, USB. An output for connecting headphones is provided. To connect a computer or laptop to this TV model, a VGA (D-Sub 15) connector is used on the TV case, this interface supports resolutions: 640x480, 800x600, 1024x768, 1280x1024, 1360x768.
Overall dimensions: With stand 373x270x120 mm, Without stand 524x340x44 mm.
Attention! The M215HW01 panel of the ERISSON 22LEB15 LED TV is an expensive and unreliable element.
Avoid any impact on the glass and pressure on the surface of the screen to avoid damage to the LED panel!
It is also unsafe to get liquid on the screen. Sometimes one drop is enough if it flows down the glass onto the cables so that the TV becomes unrepairable
