ERISSON LED
Model: 22LEN60
Chassis / Version: T.MS18VG.62B
Panel: LS215AFTNO
MainBoard: T.MS18VG.62B
IC MainBoard: Flash 25Q32
Tuner: CDT-3SP5i2-36
Specifications 22LEN60
ERISSON 22LEN60
General repair guidelines for TV LCD LED
Repair of TVs, as well as other devices, it is advisable to start with an external examination. Often, by the external signs and nature of the damage to the elements, it becomes possible to draw some conclusions and determine a further algorithm for finding a defect before making the necessary measurements at control points. If ring cracks are detected in the soldering of the terminals of the elements or dangling connecting tracks, swollen capacitors or charred resistors - all this can be characteristic signs of the causes or consequences of an already known typical malfunction.
In the absence of any signs of operability, when the ERISSON 22LEN60 does not turn on and does not signal anything with the control lights on the panel, there is a possibility of a malfunction of the TV power module. With the same manifestations, the power regulator of the control processor on the motherboard may be faulty. When diagnosing and repairing the power supply, first of all, replace the swollen capacitors of the filter of the secondary rectifiers and check the fuse and, if it is broken, it is necessary to identify the cause. Often in such cases, an avalanche (thermal) breakdown is detected in the power semiconductor elements of the module — rectifier diodes and transistors in the primary circuit.
The reasons for the breakdown of the power switch in pulsed power supplies (IIPS) can be different, for example, a malfunction of semiconductor cells or electrolytic capacitors in the stabilization circuits of the primary circuit, as well as a failure in the operation of the PWM controller chip or broken resistors in its bundle.
If the ERISSON 22LEN60 does not have an image, but there is sound, the backlight LEDs of the LS215AFTNO panel or their power converter may malfunction. You should also make sure that the electrolytic capacitors of the secondary rectifiers of the common power supply are working.
Often there is a need for disassembling the panel to check the health of the LEDs, as well as contact connections in the connectors and soldering.
It should be remembered that it is not possible to determine the open circuit in the LED lines without disassembling the panels with a tester or multimeter without an additional device, for example, a current source. To open all PN junctions connected in series at once, a voltage of several tens of volts may be required.
Repair of the T.MS18VG.62B motherboard should begin with the diagnosis and verification of all linear stabilizers or power converters of its microcircuits. Sometimes it may be necessary to update the software (software) - flashing FLASH or EEPROM.
Complex repair of MB (SSB) is possible only in the conditions of a service center with the necessary equipment. Testing or replacing Flash 25Q32 elements requires the necessary training and professional skills to repair modules at the component level. Problems associated with the use of BGA soldering technologies can be diagnosed by warming up.
If you suspect a malfunction of the tuner CDT-3SP5i2-36, first of all, you need to make sure that there is a supply voltage on the corresponding output of the tuner.
Once again, remind users! Attempts to repair the TV ERISSON 22LEN60 on its own without the appropriate qualifications and experience can lead to its complete unrepairability!
FIRMWARE FOR SPI FLASH -----------> ERISSON 22LEN60 , Main: T.MS18VG.62B, Panel: LS215AFTNO
The appearance of MainBoard T.MS18VG.62B is shown in the figure below:
T.MS18VG.62B
T.MS18VG.62B can be used in TVs:
BBK LEM2483F (Panel LG LC 230EUE(TD)(A1)), BBK LEM1983 (Panel LM185WH2 (TL)(A1)), DNS M24AM2 (Panel M236HGE-P02), DNS E16A90 (Panel LP156WH4 (TL)(A1)), ERISSON 23LEN60 (Panel LM230WF5), ERISSON 22LEN60 (Panel LS215AFTNO), ERISSON 24LEN60 (Panel LM230WF5 ), ERISSON 15LEN60 (Panel B156XW02 V.2), IZUMI TLE22F750B (Panel M215HGE-L10), RUBIN RB-19S2U (Panel V185B1-PE1 A01 REV 1.0), SUPRA STV-LC18250FL (Panel B173RW01 V.3).
Main features of the ERISSON 22LEN60 device:
Installed matrix (LED-panel) LS215AFTNO.
The required supply voltage for all nodes of the TV ERISSON 22LEN60 provides a switching power supply.
MainBoard - the main board (motherboard) is a module T.MS18VG.62B, using Flash 25Q32 chips and others.
Tuner CDT-3SP5i2-36 provides the reception of television programs and tuning to channels.
ERISSON 22LEN60 TV with LS215AFTNO LCD display, diagonal size 22 "(56 cm) in 16: 9 format. The LED-panel of this TV has an end-face LED backlight - Edge LED. The design and technical capabilities of the TV include watching programs and movies in high HD quality at a resolution of 1920x1080 pixels in graphic decomposition according to the standard 1080p (Full HD). The input high-frequency or video signal can be processed in analogue systems PAL, SECAM, NTSC. Graphic processing and digital signal generation occurs in the standards 480i, 480p, 576i, 5 76p, 720p, 1080i, 1080p.
The power of the acoustic system of sound 6 W (2x3 W) provide two speakers. The audio processing system NICAM STEREO is used.
The external interface (communication with other devices) is supported by standard input and output connectors: antenna input (RF), audio x2, component, SCART, VGA, USB. To connect a computer or laptop to this TV model, a VGA (D-Sub 15) connector is used on the TV case, this interface supports resolutions: 640x480, 800x600, 1024x768.
Overall dimensions: With stand 769x536x196 mm, Without stand 580x370x44 mm.
Attention! The LS215AFTNO panel of the ERISSON 22LEN60 LED TV is an expensive and unreliable element.
Avoid any impact on the glass and pressure on the surface of the screen to avoid damage to the LED panel!
It is also unsafe to get liquid on the screen. Sometimes one drop is enough if it flows down the glass onto the cables so that the TV becomes unrepairable.