Technical description and composition of the ERISSON 32LEE30T2 TV, type of panel and applicable modules. The composition of the modules.ERISSON LED
Model: 32LEE30T2
Chassis / Version: TP.MS3463S.PB801
Panel: LK315T3HB87-12V
LED backlight: L96M32 D140619
T-CON: RUNTK DUNTK CPWBX5409TP; BD8174MU, BM9098
LED driver (backlight): integrated into MainBoard
PWM LED driver: SN51DP
Power Supply (PSU): integrated into MainBoard
PWM Power: PWM SOT23-6
MainBoard: TP.MS3463S.PB801
IC MainBoard: CPU: MSD3463GU, SPI Flash: GD25Q64, AUDIO: OB6220VP
Tuner: XF-3SDT-H (R840)
Control: CX-507
Specifications 32LEE30T2
ERISSON 32LEE30T2
General repair guidelines for TV LCD LED
Possible malfunctions
- ERISSON 32LEE30T2 does not turn on and does not show any signs of operability at all. Does not blink indicators and does not respond to control buttons.
The malfunction in such cases should be sought in the elements of the power source - the network voltage converter (AC / DC), which is located on the MainBoard TP.MS3463S.PB801 main board. In the absence of the necessary supply voltages in the secondary circuits of the converters, it is necessary to check the power switches and rectifier diodes for a possible partial or complete breakdown.
In case of any breakdown of semiconductors in the secondary circuits, the converter can usually work normally in emergency short circuit mode. There are no output voltages. And during short circuit in the power elements of the primary circuit, as a rule, the mains fuse breaks and less often the current sensor at the source of the key.
Breakdown of power switches (MosFet) in pulsed sources is sometimes caused by malfunctions of other circuit elements, for example, in circuits supplying a PWM controller, frequency-setting or damper ones, as well as in negative feedback circuits (OOS) of stabilization. PWM controllers (PWM), if they do not have visible damage to the chassis and open short circuit between the terminals, are usually checked by replacement.
- There is no image, but there is sound and reaction to commands from the remote control. Or the image appears immediately after turning on and disappears.
Usually in such cases, a malfunction is detected in the backlight nodes of the LED panel. The reason can be both in the power supply of the LEDs, in their serviceability (breakdown or breakage), as well as in the violation of the contact connections of the LED strips.
When diagnosing, it is necessary to take into account that it is impossible to check the open in the chain of LED lines without disassembling the panels using a tester or multimeter. To open all PN junctions connected in series, a voltage of the order of several tens of volts is required, and ideally, a current source. By opening the panel, each LED can be checked separately. Typically, Chinese multimeters light up a single 3-volt LED, if you connect probes in the forward direction to it. In dual 6-volt LEDs, the PN junction of its emergency zener diode can serve as an indicator of health. In the event of a LED malfunction, its zener diode will either be cut off or broken into short-circuit.
- The TV does not turn on, the indicator indicates standby or operating mode, or blinks.
Repair or diagnostics of the TP.MS3463S.PB801 motherboard should begin by checking the stabilizers and power converters needed to power the chips and matrix. If necessary, update or replace the software (software). In cases of attempts to repair the MB (SSB) board, it is necessary to check the health of its elements - CPU: MSD3463GU, SPI Flash: GD25Q64, AUDIO: OB6220VP which may require replacement with new ones. If a BGA processor is installed, there is a possibility of a violation of the soldering of the contacts of its conclusions with the board (it is diagnosed by heating).
If you suspect a malfunction of the XF-3SDT-H tuner (R840), first of all, you need to verify the correctness of the software, as well as the presence of the necessary voltage levels and pulses of data exchange with the processor via the I2C bus at the corresponding terminals of the tuner.
Attention! For users and owners of 32LEE30T2 TVs who do not have the appropriate qualifications, knowledge and experience, we strongly recommend against attempting self-repair in order to avoid negative consequences that could lead to complete non-repairability of the device.
SCHEMATIC DIAGRAM / SERVICE MANUAL ------------------> Trouble Shooting Chassis TP.MS3463S.PB801
FIRMWARE FOR SPI FLASH -----------> ERISSON 32LEE30T2, Main: TP.MS3463S.PB801 , Panel: LK315T3HB87-12V
The appearance of MainBoard TP.MS3463S.PB801 is shown in the figure below:TP.MS3463S.PB801
TP.MS3463S.PB801 can be used in TVs:
AKAI LEA-40V35M (Panel LSC400HM06), AKIRA 32LED38T2P (Panel ST3151A05-8), AKIRA 32LED02T2M (Panel ST3151A04-9 Ver.2.1), BBK 32LEM-1029/TS2C (Panel C320X16-E18-H), BBK 39LEM-1033/TS2C (Panel C390X15-E8-A G01), BBK 32LEM-1026/TS2C (Panel CX315DLEDM ST3151A05-8), BBK 32LEM-1027/TS2C (Panel ST3151A05-8 / CX315DLEDM), DEXP F43C7100K (Panel LC430DUY (SH)(A1)), DEXP F42B7000M (Panel V420HJ2-P01), DEXP F43C7000C (Panel C430F14-E1-L / LC430DUY), DEXP F40B7100K (Panel LSC400HN02-G02 40N06-L-HPX1F1), DEXP H28C7100C (Panel C275X15-E1-H (G31)), DEXP H32C7300K (Panel LSC320AN02), DEXP H32D7100C (Panel ST3151A05-8 Ver2.5), DEXP H28D7300K (Panel HV280WX2-260), ERISSON 32LES78T2W (Panel KM0320LDRH0037), ERISSON 32LEE30T2 (Panel LK315T3HB87-12V), SUPRA STV-LC32T560WL (Panel LSC320AN10), SUPRA STV-LC32T550WL (Panel LSC320AN02), SUPRA STV-LC40T500WL (Panel C39X15-E7-A), TELEFUNKEN TF-LED32S45T2 (Panel LK315T3HB87-12V), THOMSON T39D20DH-01B (Panel T390XVN01.0).
Main features of the ERISSON 32LEE30T2 device:
Installed matrix (LED-panel) LK315T3HB87-12V.
The matrix control uses the Timing Controller (T-CON) RUNTK.
To power the backlight LEDs, a converter is used, combined with the TP.MS3463S.PB801 main board, controlled by the SN51DP PWM controller.
The power module is combined with the MainBoard and is made according to the flyback AC / DC voltage converter circuit using PWM SOT23-6 microcircuits.
MainBoard - the main board (motherboard) is a TP.MS3463S.PB801 module, using CPU chips: MSD3463GU, SPI Flash: GD25Q64, AUDIO: OB6220VP and others.
Tuner XF-3SDT-H (R840) provides the reception of television programs and tuning to channels.
TV ERISSON 32LEE30T2 with LCD LK315T3HB87-12V, diagonal size 31.5 "(80 cm) 16: 9 format. The required brightness of the screen 250 cd / m² is provided by LED backlight LED. Contrast, as the ratio of maximum brightness to minimum, is 5000: 1. Edge LED backlighting is realized in the LED-panel of this TV - Edge LED. You can view images in high quality HD at a resolution of 1366x768 pixels in the standard of graphic decomposition 720p (HD Ready). The input high-frequency or video signal can be processed in analog with . Stem PAL, SECAM, NTSC Image processing and the formation of the digital signal is in 480i standards, 480p, 576i, 576p, 720p, 1080i Supported multimedia file formats:. MP3, MPEG4, Xvid, DivX, MKV, JPEG.
The power of the acoustic system of sound 20 W (2x10 W) provide two speakers. It uses a NICAM stereo signal processing system and Sound Surround.
The external interface (communication with other devices) is supported by standard input and output connectors: antenna input (RF), AV, S-Video, VGA, HDMI, USB. An output for connecting headphones is provided. To connect a computer or laptop to this TV model, a VGA (D-Sub 15) connector is used on the TV case, this interface supports resolutions: 640x480, 800x600, 1024x768, 1360x768.
A digital tuner is capable of receiving television channels in the DVB-T MPEG4, DVB-C, DVB-T2 standards.
Overall dimensions: With stand 737x472x160 mm, Without stand 737x438x77 mm.
Attention! The LK315T3HB87-12V panel of an ERISSON 32LEE30T2 LED TV is an expensive and unreliable element.
Avoid any impact on the glass and pressure on the surface of the screen to avoid damage to the LED panel!
It is also unsafe to get liquid on the screen. Sometimes one drop is enough if it flows down the glass onto the cables so that the TV becomes unrepairable.
