PHILIPS LED
Model: 43PFS4012 / 12
Chassis / Version: KTS17.1E LA
Panel: K430WDK3
LED backlight: 4708-K43WDC-A3113N11 K430WDC1 A3
T-CON: 6870C-0532A 6871L-3806B
LED driver (backlight): integrated into MainBoard
PWM LED driver: SN51DP
MOSFET LED driver: AOD458
Power Supply (PSU): integrated into MainBoard
PWM Power: PWM SOT23-6
MOSFET Power: N-FET TO-220F
MainBoard: TP.MS3463S.PB801
IC MainBoard: CPU: MSD3463GU, SPI Flash: GD25Q64, AUDIO: OB6220VP
Tuner: DVB-T2 & SAT
Control: IR: 4713-5500C1-A2123K01
Specifications 43PFS4012
PHILIPS 43PFS4012
General recommendations for TV LCD LED repair
Possible manifestations of defects
- PHILIPS 43PFS4012 TV does not turn on, does not respond to the remote control and control panel buttons, the indicators do not light up or flash.
First of all, in such cases, you should make sure that the common switching power supply (SMPS) - the AC / DC voltage converter of the mains voltage - is working. All source elements in this TV model are located on the MainBoard TP.MS3463S.PB801. It is necessary to measure its secondary output voltages, and if they are absent, check the power switches (N-FET TO-220F) and rectifier diodes in the converters for a short circuit.
In case of diode breakdowns in the secondary circuits, the converter can operate in an emergency mode of short circuit without output voltages, and with a short circuit in the power elements of the primary circuit, the mains fuse and / or the current sensor in the source of the key usually breaks off.
Mos-Fet keys used in switching power supplies usually fail due to a malfunction of other elements, which can disable it in key mode, or provoke an excess of the maximum current or voltage values. These can be circuits supplying the PWM controller, damper or frequency setting circuits, or OOS (negative feedback) elements in the stabilization circuit. PWM controllers (PWM) PWM SOT23-6, in the absence of external damage and a short circuit between the terminals, are checked by replacing them with a known good one.
- There is no picture, but there is sound and reaction to commands from the remote control. Or the image appears immediately after switching on and disappears.
The malfunction in most of such cases is found in the nodes and elements of the LED panel backlighting. Often the cause of a malfunction is the lack of current in the LED circuit, for example, their open or short circuit, or a violation of the contact connections of the connectors.
To check the LED lines for breakage without disassembling the panel, for example, a current source will help. It is impossible to open series-connected PN junctions with a simple multimeter; a voltage of the order of several tens of volts is required.
- The TV does not go into operation, does not respond to the remote control. The indicator on the front panel is on or blinking.
Repair or diagnostics of the TP.MS3463S.PB801 motherboard should begin with checking the stabilizers and power converters necessary to power the microcircuits and matrix. If necessary, you should update or replace the software (software). Repair of the board and replacement of chips CPU: MSD3463GU, SPI Flash: GD25Q64, AUDIO: OB6220VP are made with the necessary equipment and the corresponding element base. Failures associated with the use of BGA soldering technologies can be localized by warming up.
If you suspect a malfunction of the DVB-T2 & SAT tuner, first of all, you need to make sure the software is correct, as well as the presence of the required supply voltage levels and pulses of data exchange with the processor via the I2C bus on the corresponding tuner pins.
Attention! Users and owners of 43PFS4012 TVs who do not have the appropriate qualifications, knowledge and experience are strongly discouraged from trying to repair themselves in order to avoid negative consequences that can lead to the complete non-repairability of the device.
DOWNLOAD SCHEMATIC DIAGRAM / SERVICE MANUAL ------------------> PHILIPS 43PFS4012 Chassis KTS17.1E LA
The appearance of MainBoard TP.MS3463S.PB801 is shown in the figure below:
TP.MS3463S.PB801
TP.MS3463S.PB801 can be used in TVs:
AKAI LEA-40V35M (Panel LSC400HM06), AKIRA 32LED38T2P (Panel ST3151A05-8), AKIRA 32LED02T2M (Panel ST3151A04-9 Ver.2.1), BBK 32LEM-1029/TS2C (Panel C320X16-E18-H), BBK 39LEM-1033/TS2C (Panel C390X15-E8-A G01), BBK 32LEM-1026/TS2C (Panel CX315DLEDM ST3151A05-8), BBK 32LEM-1027/TS2C (Panel ST3151A05-8 / CX315DLEDM), DEXP F43C7100K (Panel LC430DUY (SH)(A1)), DEXP F42B7000M (Panel V420HJ2-P01), DEXP F43C7000C (Panel C430F14-E1-L / LC430DUY), DEXP F40B7100K (Panel LSC400HN02-G02 40N06-L-HPX1F1), DEXP H28C7100C (Panel C275X15-E1-H (G31)), DEXP H32C7300K (Panel LSC320AN02), DEXP H32D7100C (Panel ST3151A05-8 Ver2.5), DEXP H28D7300K (Panel HV280WX2-260), ERISSON 32LES78T2W (Panel KM0320LDRH0037), ERISSON 32LEE30T2 (Panel LK315T3HB87-12V), SUPRA STV-LC32T560WL (Panel LSC320AN10), SUPRA STV-LC32T550WL (Panel LSC320AN02), SUPRA STV-LC40T500WL (Panel C39X15-E7-A), TELEFUNKEN TF-LED32S45T2 (Panel LK315T3HB87-12V), THOMSON T39D20DH-01B (Panel T390XVN01.0).
The main features of the PHILIPS 43PFS4012 device:
Installed matrix (LED panel) K430WDK3.
Matrix control uses the 6870C-0532A Timing Controller (T-CON).
To power the backlight LEDs, a converter combined with the TP.MS3463S.PB801 main board is used, controlled by the SN51DP PWM controller. AOD458 type keys are used as power elements of the LED driver.
The power module is combined with the MainBoard and is made according to the AC / DC flyback voltage converter using SOT23-6 PWM microcircuits and N-FET TO-220F power switches.
MainBoard - the main board (motherboard) is a TP.MS3463S.PB801 module, using CPU chips: MSD3463GU, SPI Flash: GD25Q64, AUDIO: OB6220VP and others.
The DVB-T2 & SAT tuner provides reception of television programs and tuning to channels.
PWM SMPS in SOT-23-6, SOT-26, TSOP-6 packages
In
the circuitry of modern switching power supplies (SMPS), PWM
controllers made in small-sized planar packages with six terminals have
gained wide popularity. The enclosure type designation can be SOT-23-6,
SOT-23-6L, SOT-26, TSOP-6, SSOT-6. The appearance and arrangement of the
pins are shown in the figure below. In this case, the code marking
LD7530A is shown on the left fragment of the picture.
Pin assignment:
1 - GND. (Common wire).
2
- FB. (FeedBack - Feedback). Input for controlling the duration of
pulses with a signal from the output voltage. Sometimes it can be
labeled COMP (input comparator).
3 - RI / RT / CT / COMP / NC -
Depending on the type of microcircuit, it can be used for a
frequency-setting RC circuit (RI / RT / CT), or for organizing
protection, as an input of a PWM trip comparator at a threshold value at
its input, specified in the document. In some types of microcircuits,
this input may not be used in any way (NC - No Connect).
4 - SENSE, otherwise CS (Current Sense) - Input from the current sensor at the source of the key.
5 - VCC - Input voltage supply and start of the microcircuit.
6 - OUT (GATE) - Output for controlling the gate (Gate) of the key.
Functionally,
these regulators work on the principle of the previously popular xx384x
PWM microcircuits, which have proven themselves well in terms of
reliability and stability.
Some difficulties often arise when
replacing or choosing an analog for such PWM regulators due to the use
of code markings in the designation of the type of microcircuits. The
situation is complicated by a large number of component manufacturers
who do not always provide documentation to the mass access, just as not
all manufacturers of finished devices supply repair service centers with
diagrams, so repairmen often have to study real circuit solutions by
installed components and wiring connections directly on the board.
In
practice, PWM microcircuits and the marking code EAxxx and Eaxxx are
often found. Official documentation for them was not found in the public
domain, but discussions on the forums and pieces of pictures from PDF
from System General, which publishes them as SG6848T and SG6848T2, have
survived. The drawing is here placed left .
For the attention of the masters, here below are PDF datasheet tables
compiled from information available on the Internet and PDF documents
for the selection of analogues types when replacing the most common
six-legged planar PWM with pinout pins: pin1 - GND, pin2 - FB (COMP),
pin4 - Sense, pin5 - Vcc, pin6 - OUT ...
Their main difference is the application and purpose of pin 3.
Name | Part Number | Fabricant | Marking |
---|---|---|---|
SG6849 | SG684965TZ | Fairchild / ON Semi | BBxx |
SG6849 | SG6849-65T, SG6849-65TZ | System General | MBxx EBxx |
SGP400 | SGP400TZ | System General | AAKxx |
PWM controllers (PWM) with a 95-100 kOhm resistor on pin 3.
When
applying the PWM listed below, the frequency should be set with the RT
(RI) resistor from pin 3 to ground. Usually its nominal value is chosen
95-100 kOhm for a frequency of 65-100 KHz. For more details, see the
here below attached documentation. PDF files are packed in RAR.
Name | Part Number | Fabricant | Marking |
---|---|---|---|
AP3103A | AP3103AKTR-G1 | Diodes Incorporated | GHL |
AP8263 | AP8263E6R, A8263E6VR | AiT Semiconductor | S1xx |
AT3263 | AT3263S6 | ATC Technology | 3263 |
CR6848 | CR6848S | Chip-Rail | 848H16 |
CR6850 | CR6850S | Chip-Rail | 850xx |
CR6851 | CR6851S | Chip-Rail | 851xx |
FAN6602R | FAN6602RM6X | Fairchild / ON Semi | ACCxx |
FS6830 | FS6830 | FirstSemi | |
GR8830 | GR8830CG | Grenergy | 30xx |
GR8836 | GR8836C, GR8836CG | Grenergy | 36xx |
H6849 | H6849NF | HI-SINCERITY | |
H6850 | H6850NF | HI-SINCERITY | |
HT2263 | HT2263MP | HOT-CHIP | 63xxx |
KP201 | Kiwi Instruments | ||
LD5530 | LD5530GL LD5530R | Leadtrand | xxt30 xxt30R |
LD7531 | LD7531GL, LD7531PL | Leadtrend | xxP31 |
LD7531A | LD7531AGL | Leadtrend | xxP31A |
LD7535/A | LD7535BL, LD7535GL, LD7535ABL, LD7535AGL | Leadtrend | xxP35-xxx35A |
LD7550 | LD7550BL, LD7550IL | Leadtrend | xxP50 |
LD7550B | LD7550BBL, LD7550BIL | Leadtrend | xxP50B |
LD7551 | LD7551BL/IL | Leadtrend | xxP51 |
LD7551C | LD7551CGL | Leadtrend | xxP51C |
NX1049 | XN1049TP | Xian-Innuovo | 49xxx |
OB2262 | OB2262MP | On-Bright-Electronics | 62xx |
OB2263 | OB2263MP | On-Bright-Electronics | 63xx |
PT4201 | PT4201E23F | Powtech | 4201 |
R7731 | R7731GE/PE | Richtek | 0Q= |
R7731A | R7731AGE | Richtek | IDP=xx |
SD4870 | SD4870TR | Silan Microelectronics | 4870 |
SF1530 | SF1530LGT | SiFirst | 30xxx |
SG5701 | SG5701TZ | System General | AAExx |
SG6848 | SG6848T, SG6848T1, SG6848TZ1, SG6848T2 | Fairchild / ON Semi | AAHxx EAxxx |
SG6858 | SG6858TZ | Fairchild / ON Semi | AAIxx |
SG6859A | SG6859ATZ, SG6859ATY | Fairchild / ON Semi | AAJFxx |
SG6859 | SG6859TZ | Fairchild / ON Semi | AAJMxx |
SG6860 | SG6860TY | Fairchild | AAQxx |
SP6850 | SP6850S26RG | Sporton Lab | 850xx |
SP6853 | SP6853S26RGB, SP6853S26RG | Sporton Lab | 853xx |
SW2263 | SW2263MP | SamWin | |
UC3863/G | UC3863G-AG6-R | Unisonic Technologies Co | U863 U863G |
XN1049 | XN1049, XN1049TP | Innuovo Microelectronics | 49 xxx |
PWM controllers that use pin 3 differently.
When
using the following PWM (PWM controllers), you should pay attention to
pin 3, which can be used to organize protection - thermal or from
overvoltage of the input voltage.
The frequency can be fixed at 65kHz, or set by the value of the capacitor at pin 3.
When replacing any microcircuits with analogs, carefully study the documentation. PDF files are packed in a RAR archive.
Name | Part Number | Fabricant | Marking |
---|---|---|---|
AP3105/V/L/R | AP3105KTR-G1, AP3105VKTR-G1, AP3105LKTR-G1, AP3105RKTR-G1 | Diodes Incorporated | GHN GHO GHP GHQ |
AP3105NA/NV/NL/NR | AP3105NAKTR-G1, AP3105NVKTR-G1, AP3105NLKTR-G1, AP3105NRKTR-G1 | Diodes Incorporated | GKN GKO GKP GKQ |
AP3125A/V/L/R | AP3125AKTR-G1, AP3125VKTR-G1, AP3125LKTR-G1, AP3125RKTR-G1 | Diodes Incorporated | GLS GLU GNB GNC |
AP3125B | AP3125BKTR-G1 | Diodes Incorporated | GLV |
AP3125HA/HB | AP3125HAKTR-G1, AP3125HBKTR-G1 | Diodes Incorporated | GNP GNQ |
AP31261 | AP31261KTR-G1 | Diodes Incorporated | GPE |
AP3127/H | AP3127KTR-G1, AP3127HKTR-G1 | Diodes Incorporated | GPH GSH |
AP3301 | AP3301K6TR-G1 | Diodes Incorporated | GTC |
FAN6862 | FAN6862TY | Fairchild / ON Semi | ABDxx |
FAN6863 | FAN6863TY, FAN6863LTY, FAN6863RTY | Fairchild / ON Semi | ABRxx |
HT2273 | HT2273TP | HOT-CHIP | 73xxx |
LD7510/J | LD7510GL, LD7510JGL | Leadtrend | xxP10 xxP10J |
LD7530/A | LD7530PL, LD7530GL, LD7530APL, LD7530AGL | Leadtrend | xxP30 xxxP30A |
LD7532 | LD7532GL | Leadtrend | xxP32 |
LD7532A | LD7532AGL | Leadtrend | xxP32A |
LD7532H | LD7532HGL | Leadtrend | xxP32H |
LD7533 | LD7533GL | Leadtrend | xxP33 |
LD7536 | LD7536GL | Leadtrend | xxP36 |
LD7536R | LD7536RGL | Leadtrend | xxP36R |
LD7537R | LD7537RGL | Leadtrend | xxP37R |
LD7539C GL | LD7539C GL | Leadtrend | xxP39C |
ME8204 | ME8204M6G | MicrOne | ME8204xx |
NCP1250 | NCP1250ASN65T1G, NCP1250BSN65T1G, NCP1250ASN100T1G, NCP1250BSN100T1G | ON Semiconductor | 25xxxx |
NCP1251 | NCP1251ASN65T1G, NCP1251BSN65T1G, NCP1251ASN100T1G, NCP1251BSN100T1G | ON Semiconductor | 5xxxxx |
OB2273 | OB2273MP | On-Bright-Electronics | 73xx |
R7735 | R7735AGE, R7735HGE, R7735GGE, R7735RGE, R7735LGE | Richtek | |
UC3873/G | UC3873-AG6-R, UC3873G-AG6-R | Unisonic Technologies | U873 U873G |
Instructions and updates
Documentation:User manual PDF file, 939.1 kB, published November 6, 2018Brochure Version: 13.7.1, PDF file, 444.9 kB, published February 20, 2020
Files can be downloaded from the manufacturer's website for model 43PFS4012 / 12.
PHILIPS 43PFS4012 TV with LCD K430WDK3, diagonal size 42.5 "(108 cm) 16: 9. The required brightness of the screen of 250 cd / m2 is provided by LED backlighting. The LCD panel is backlit from Direct LED LEDs.
The K430WDK3 matrix and the MainBoard TP.MS3463S.PB801 software provide viewing of broadcasts and movies in high quality HD at a resolution of 1920x1080 pixels in graphics resolution in 1080p (Full HD). Supported media file formats: MP3, WMA, MPEG4, HEVC (H.265), MKV, JPEG.
Speaker power 16 W (2x8 W) is provided by two speakers. Uses the NICAM stereo signal processing system and the Sound Surround function.
External interface (communication with other devices) is supported by standard input and output connectors: antenna input (RF), AV, audio x2, component, VGA, HDMI x3, MHL, USB. A headphone output is provided.
The digital tuner is capable of receiving television channels in the DVB-T MPEG4, DVB-C, DVB-T2, DVB-S2 standards.
The TV uses a power supply unit as part of the MainBoard.
Dimensions: with stand 969x625x243 mm, without stand 969x567x83 mm.
TV weight: with stand: 7.5 kg, without stand: 7.3 kg.
Attention! Panel K430WDK3 LED TV PHILIPS 43PFS4012 is an expensive and unreliable element.
Do not allow any impact on the glass and pressure on the screen surface to avoid damage to the LED panel!
It is also unsafe for liquid to spill onto the screen. Sometimes one drop is enough if it drips down the glass onto the cables to make the TV unrepairable.
The LED screen of the PHILIPS 43PFS4012 TV requires respect from users. The glass can crack even if it is lightly hit by a child's plastic toy.
Excessive pressure on the screen surface over any part of the area is equally dangerous.