REPAIRING AND NOT THROWING AWAY

Richtige Fernseher haben Röhren!

Richtige Fernseher haben Röhren!

In Brief: On this site you will find pictures and technical information about Service Modes, Circuit Diagrams, Firmware Update procedure, Disassemble procedure, Universal remote control set-up codes, Troubleshooting and more....

If you go into the profession, you will obtain or have access to a variety of tech tips databases HERE IT IS Master Electronics Repair !.

These are an excellent investment where the saying: 'time-is-money' rules. However, to learn, you need to develop a general troubleshooting approach - a logical, methodical, method of narrowing down the problem. A tech tip database might suggest: 'Replace C536' for a particular symptom. This is good advice for a specific problem on one model. However, what you really want to understand is why C536 was the cause and how to pinpoint the culprit in general even if you don't have a service manual or schematic and your tech tip database doesn't have an entry for your sick TV or VCR.

While schematics are nice, you won't always have them or be able to justify the purchase for a one-of repair. Therefore, in many cases, some reverse engineering will be necessary. The time will be well spent since even if you don't see another instance of the same model in your entire lifetime, you will have learned something in the process that can be applied to other equipment problems.
As always, when you get stuck, checking out a tech-tips database may quickly identify your problem and solution.In that case, you can greatly simplify your troubleshooting or at least confirm a diagnosis before ordering parts.

Happy repairing!
Today, the West is headed for the abyss. For the ultimate fate of our disposable society is for that society itself to be disposed of. And this will happen sooner, rather than later.

How to use the site:

- If you landed here via any Search Engine, you will get what you searched for and you can search more using the search this blog feature provided by Google. You can visit more posts scrolling the left blog archive of all posts of the month/year,
or you can click on the main photo-page to start from the main page. Doing so it starts from the most recent post to the older post simple clicking on the Older Post button on the bottom of each page after reading , post after post.

You can even visit all posts, time to time, when reaching the bottom end of each page and click on the Older Post button.

- If you arrived here at the main page via bookmark you can visit all the site scrolling the left blog archive of all posts of the month/year pointing were you want , or more simple You can even visit all blog posts, from newer to older, clicking at the end of each bottom page on the Older Post button.
So you can see all the blog/site content surfing all pages in it.

- The search this blog feature provided by Google is a real search engine. If you're pointing particular things it will search IT for you; or you can place a brand name in the search query at your choice and visit all results page by page. It's useful since the content of the site is very large.

Note that if you don't find what you searched for, try it after a period of time; the site is a never ending job !

..............The bitterness of poor quality is remembered long after the sweetness of todays funny gadgets low price has faded from memory........ . . . . . .....
Don't forget the past, the end of the world is upon us! Pretty soon it will all turn to dust!

©2010, 2011, 2012, 2013, 2014 Frank Sharp - You do not have permission to copy photos and words from this blog, and any content may be never used it for auctions or commercial purposes, however feel free to post anything you see here with a courtesy link back, btw a link to the original post here , is mandatory.
All posts are presented here for informative, historical and educative purposes as applicable within fair use. NOTHING HERE IS FOR SALE !

Thursday, 17 September 2020

REPAIRING / SERVICING TV BBK 28LEM-1044

Technical description and composition of the BBK 28LEM-1044 TV, panel type and modules used. The composition of the modules.
BBK LED
Model: 28LEM-1044
Chassis / Version: CV512H-U42
Panel: ST2751A01-8
LED backlight: JS-D-JP2820-051EC (71220)
T-CON: ST3151A05-8
LED driver (backlight): integrated into MainBoard
PWM LED driver: BIT3267
MOSFET LED driver: ME15N10-G
Power Supply (PSU): integrated into MainBoard
PWM Power: PWM SOT23-6 AP3125
MOSFET Power: 7N60 TO-220F
MainBoard: CV512H-U42
IC MainBoard: SPI Flash: W25Q64, Audio: RDA3118E28 (TPA3110D)
Tuner: CDT-9NT372-RD60
Specifications 28LEM-1044 / T2C
BBK 28LEM-1044
General recommendations for TV LCD LED repair
Possible manifestations of defects
- BBK 28LEM-1044 does not turn on, indicators on the front panel do not light or flash. The TV does not respond to the control buttons and the remote control.
First of all, in such cases, you should make sure that the common switching power supply (SMPS) - the AC / DC voltage converter of the mains voltage - is working. All source elements in this TV model are located on the MainBoard CV512H-U42. Its output voltages should be measured and, in their absence, the power switches (7N60 TO-220F) and rectifier diodes should be checked for the probability of a short circuit in the converters.
In case of breakdowns of semiconductors in the secondary circuits, the converter can usually work in an emergency in the short-circuit mode, and with a short circuit in the power elements of the primary circuit, the mains fuse often breaks.
Mos-Fet keys used in switching power supplies usually fail due to a malfunction of other elements that can disable it in key mode, or provoke an excess of the maximum current or voltage values. These can be circuits supplying a PWM controller, damper or frequency setting circuits, or OOS (negative feedback) elements in the stabilization circuit. PWM controllers (PWM) PWM SOT23-6 AP3125, in the absence of external damage and short circuit between the terminals, are checked by replacing them with a known good one.
- There is no picture, but there is sound, it reacts to the remote control. Or the image appears when turned on and immediately disappears
A malfunction is usually in these cases most likely in the backlight units of the display matrix. Often the cause of a malfunction is the lack of current in the LED circuit, for example, their open or short circuit, or a violation of the contact connections of the connectors.
It is impossible to check the line of series-connected LEDs without a special current source, and it is unsafe for them to use any voltage sources above 12V for this purpose. Then all that remains is to open the panel and check each LED separately. Typically, Chinese multimeters with a 9V power supply lightly light up one 3-volt LED if you connect the probes to it in the forward direction, the red probe to the anode, and the black one to the cathode. For dual 6-volt LEDs, the PN junction of its emergency zener diode can serve as an indicator of LED health. In the event of a malfunction of the LED, its zener diode will either be cut off, or broken through in the SC.
- The indicator on the front panel blinks, the TV does not turn on in operating mode, does not respond to the remote control.
Repair or diagnostics of the CV512H-U42 motherboard should begin with checking the stabilizers and power converters necessary to power the microcircuits and matrix. If necessary, you should update or replace the software (software). If it is not possible to replace the MB (SSB) board, you need to check the serviceability of its elements - SPI Flash: W25Q64, Audio: RDA3118E28 (TPA3110D). Defective components must be replaced.
If there is no reception of television channels, but the TV is working properly from external devices, first of all, you need to check the supply voltage of the CDT-9NT372-RD60 tuner and update the software. I2C communication pulses must be monitored with an oscilloscope.

If the BBK 28LEM-1044 / T2C has no image, but there is sound, the backlight of the ST2751A01-8 display often simply does not work. Moreover, in LED TVs, the LEDs inside the panel usually fail, less often the LED driver.
In such cases, you can see a barely noticeable image with a successful hit of external light on the screen.
Replacing the LEDs requires disassembling the ST2751A01-8 LCD panel - a process that requires experience and qualifications from the master. We do not recommend doing such work on your own to the owners of TVs and craftsmen who do not have experience in repairing LCD panels
If there is no image, and the backlight is on, the screen becomes slightly lighter when turned on, and in an open TV you can see light through the holes in the panel case.
In this case, the panel may also be faulty - damage to strips, loops, for example, as a result of moisture ingress after unsuccessful washing of the screen, the T-CON (Timing Controller) board may be faulty. But the main board MainBoard CV512H-U42 often turns out to be faulty, a software failure is also possible.
Then, first of all, you need to check the panel supply voltage, the fuses on the T-CON board, as well as the supply and reference voltages of the column and line drivers - VGH, VGL, Vcom.
If these measurements are within normal limits, it is necessary to trace the passage of LVDS signals from the MainBoard CV512H-U42 with an oscilloscope, as well as synchronizing signals to the loops with drivers.
Flooded or unsuccessfully washed screens of LED TVs can be restored, in about half of the cases, usually if significant damage has not formed in the loops and panel strips.

Attention to users! Self-repair of the BBK 28LEM-1044 TV without the appropriate qualifications and the necessary experience can lead to its complete non-repairability!
Additional MainBoard Repair
The appearance of the MainBoard CV512H-U42 is shown in the figure below:
CV512H-U42


CV512H-U42 can be used in TVs:
DEXP H39D7000Q (Panel LC390TA2A), SUPRA STV-LC32LT0010W (Panel KM0320LDRH0037).
The main features of the BBK 28LEM-1044 device:
Installed matrix (LED-panel) ST2751A01-8.
Matrix control uses the ST3151A05-8 Timing Controller (T-CON).
To power the backlight LEDs, a converter combined with the CV512H-U42 main board is used, controlled by the BIT3267 PWM controller. The keys of the ME15N10-G type are used as power elements of the LED driver.
The power module is combined with the MainBoard and is made according to the AC / DC flyback voltage converter using PWM SOT23-6 AP3125 chips and 7N60 TO-220F power switches.
MainBoard - the main board (motherboard) is a CV512H-U42 module, using SPI Flash chips: W25Q64, Audio: RDA3118E28 (TPA3110D) and others.
Tuner CDT-9NT372-RD60 provides reception of television programs and tuning to channels.
Additional technical information about the panel:
Brand: CSOT
Model: ST2751A01-8
Type: a-Si TFT-LCD, CELL
Diagonal size: 27.5 inch
Resolution: 1366x768, WXGA
Display Mode: HVA, Normally Black, Transmissive
Active Area: 607.528x345.024 mm
Surface: Antiglare (Haze 2%), Hard coating (3H)
Glass Depth: 0.50 + 0.50 mm
Transmissivity: 7.2% (with Polarizer)
Contrast Ratio: 3000: 1
Display Colors: 16.7M (8-bit), CIE1931 62%
Response Time: 6.5 (G to G)
Frequency: 60Hz
Signal Interface: LVDS (1 ch, 8-bit), 30 pins
Voltage: 12.0V

 

 

PWM SMPS in SOT-23-6, SOT-26, TSOP-6 packages

In the circuitry of modern switching power supplies (SMPS), PWM controllers made in small-sized planar packages with six terminals have gained wide popularity. The enclosure type designation can be SOT-23-6, SOT-23-6L, SOT-26, TSOP-6, SSOT-6. The appearance and arrangement of the pins are shown in the figure below. In this case, the code marking LD7530A is shown on the left fragment of the picture.


 

 Pin assignment:
1 - GND. (Common wire).
2 - FB. (FeedBack - Feedback). Input for controlling the duration of pulses with a signal from the output voltage. Sometimes it can be labeled COMP (input comparator).
3 - RI / RT / CT / COMP / NC - Depending on the type of microcircuit, it can be used for a frequency-setting RC circuit (RI / RT / CT), or for organizing protection, as an input of a PWM trip comparator at a threshold value at its input, specified in the document. In some types of microcircuits, this input may not be used in any way (NC - No Connect).
4 - SENSE, otherwise CS (Current Sense) - Input from the current sensor at the source of the key.
5 - VCC - Input voltage supply and start of the microcircuit.
6 - OUT (GATE) - Output for controlling the gate (Gate) of the key.

Functionally, these regulators work on the principle of the previously popular xx384x PWM microcircuits, which have proven themselves well in terms of reliability and stability.

Some difficulties often arise when replacing or choosing an analog for such PWM regulators due to the use of code markings in the designation of the type of microcircuits. The situation is complicated by a large number of component manufacturers who do not always provide documentation to the mass access, just as not all manufacturers of finished devices supply repair service centers with diagrams, so repairmen often have to study real circuit solutions by installed components and wiring connections directly on the board.

In practice, PWM microcircuits and the marking code EAxxx and Eaxxx are often found. Official documentation for them was not found in the public domain, but discussions on the forums and pieces of pictures from PDF from System General, which publishes them as SG6848T and SG6848T2, have survived. The drawing is here placed left .


 

For the attention of the masters, here below are PDF datasheet tables compiled from information available on the Internet and PDF documents for the selection of analogues types when replacing the most common six-legged planar PWM with pinout pins: pin1 - GND, pin2 - FB (COMP), pin4 - Sense, pin5 - Vcc, pin6 - OUT ...
Their main difference is the application and purpose of pin 3. 

 

NamePart NumberFabricantMarking
SG6849SG684965TZFairchild / ON SemiBBxx
SG6849SG6849-65T, SG6849-65TZSystem GeneralMBxx EBxx
SGP400SGP400TZ System General AAKxx

 

 PWM controllers (PWM) with a 95-100 kOhm resistor on pin 3.

When applying the PWM listed below, the frequency should be set with the RT (RI) resistor from pin 3 to ground. Usually its nominal value is chosen 95-100 kOhm for a frequency of 65-100 KHz. For more details, see the here below attached documentation. PDF files are packed in RAR.

 

NamePart NumberFabricantMarking
AP3103AAP3103AKTR-G1Diodes IncorporatedGHL
AP8263AP8263E6R, A8263E6VRAiT SemiconductorS1xx
AT3263AT3263S6ATC Technology3263
CR6848CR6848SChip-Rail848H16
CR6850CR6850SChip-Rail850xx
CR6851CR6851SChip-Rail851xx
FAN6602RFAN6602RM6XFairchild / ON SemiACCxx
FS6830FS6830FirstSemi
GR8830GR8830CGGrenergy30xx
GR8836GR8836C, GR8836CGGrenergy36xx
H6849H6849NFHI-SINCERITY
H6850H6850NFHI-SINCERITY
HT2263HT2263MPHOT-CHIP63xxx
KP201
Kiwi Instruments
LD5530LD5530GL LD5530RLeadtrandxxt30 xxt30R
LD7531LD7531GL, LD7531PLLeadtrendxxP31
LD7531ALD7531AGLLeadtrendxxP31A
LD7535/ALD7535BL, LD7535GL, LD7535ABL, LD7535AGLLeadtrendxxP35-xxx35A
LD7550LD7550BL, LD7550ILLeadtrendxxP50
LD7550BLD7550BBL, LD7550BILLeadtrend xxP50B
LD7551LD7551BL/ILLeadtrendxxP51
LD7551CLD7551CGLLeadtrendxxP51C
NX1049XN1049TPXian-Innuovo49xxx
OB2262OB2262MPOn-Bright-Electronics62xx
OB2263OB2263MPOn-Bright-Electronics63xx
PT4201PT4201E23FPowtech4201
R7731R7731GE/PERichtek0Q=
R7731AR7731AGERichtekIDP=xx
SD4870SD4870TRSilan Microelectronics4870
SF1530SF1530LGTSiFirst30xxx
SG5701SG5701TZSystem GeneralAAExx
SG6848SG6848T, SG6848T1, SG6848TZ1, SG6848T2Fairchild / ON SemiAAHxx EAxxx
SG6858SG6858TZFairchild / ON SemiAAIxx
SG6859ASG6859ATZ, SG6859ATYFairchild / ON SemiAAJFxx
SG6859SG6859TZFairchild / ON SemiAAJMxx
SG6860SG6860TYFairchildAAQxx
SP6850SP6850S26RGSporton Lab850xx
SP6853SP6853S26RGB, SP6853S26RGSporton Lab853xx
SW2263SW2263MPSamWin
UC3863/GUC3863G-AG6-RUnisonic Technologies CoU863 U863G
XN1049XN1049, XN1049TPInnuovo Microelectronics49 xxx

 

 PWM controllers that use pin 3 differently.

When using the following PWM (PWM controllers), you should pay attention to pin 3, which can be used to organize protection - thermal or from overvoltage of the input voltage.
The frequency can be fixed at 65kHz, or set by the value of the capacitor at pin 3.
When replacing any microcircuits with analogs, carefully study the documentation. PDF files are packed in a RAR archive.

 

NamePart NumberFabricantMarking
AP3105/V/L/RAP3105KTR-G1, AP3105VKTR-G1, AP3105LKTR-G1, AP3105RKTR-G1Diodes IncorporatedGHN GHO GHP GHQ
AP3105NA/NV/NL/NRAP3105NAKTR-G1, AP3105NVKTR-G1, AP3105NLKTR-G1, AP3105NRKTR-G1Diodes IncorporatedGKN GKO GKP GKQ
AP3125A/V/L/RAP3125AKTR-G1, AP3125VKTR-G1, AP3125LKTR-G1, AP3125RKTR-G1Diodes IncorporatedGLS GLU GNB GNC
AP3125BAP3125BKTR-G1Diodes IncorporatedGLV
AP3125HA/HBAP3125HAKTR-G1, AP3125HBKTR-G1Diodes IncorporatedGNP GNQ
AP31261AP31261KTR-G1Diodes IncorporatedGPE
AP3127/HAP3127KTR-G1, AP3127HKTR-G1Diodes IncorporatedGPH GSH
AP3301AP3301K6TR-G1Diodes IncorporatedGTC
FAN6862FAN6862TYFairchild / ON SemiABDxx
FAN6863FAN6863TY, FAN6863LTY, FAN6863RTYFairchild / ON SemiABRxx
HT2273HT2273TPHOT-CHIP73xxx
LD7510/JLD7510GL, LD7510JGLLeadtrendxxP10 xxP10J
LD7530/ALD7530PL, LD7530GL, LD7530APL, LD7530AGLLeadtrendxxP30 xxxP30A
LD7532LD7532GLLeadtrendxxP32
LD7532ALD7532AGLLeadtrendxxP32A
LD7532HLD7532HGLLeadtrendxxP32H
LD7533LD7533GLLeadtrendxxP33
LD7536LD7536GLLeadtrendxxP36
LD7536RLD7536RGLLeadtrendxxP36R
LD7537RLD7537RGLLeadtrendxxP37R
LD7539C GLLD7539C GLLeadtrendxxP39C
ME8204ME8204M6GMicrOneME8204xx
NCP1250NCP1250ASN65T1G, NCP1250BSN65T1G, NCP1250ASN100T1G, NCP1250BSN100T1GON Semiconductor25xxxx
NCP1251NCP1251ASN65T1G, NCP1251BSN65T1G, NCP1251ASN100T1G, NCP1251BSN100T1GON Semiconductor5xxxxx
OB2273OB2273MPOn-Bright-Electronics73xx
R7735R7735AGE, R7735HGE, R7735GGE, R7735RGE, R7735LGERichtek
UC3873/GUC3873-AG6-R, UC3873G-AG6-RUnisonic TechnologiesU873 U873G

 

 

 


LED TV BBK 28LEM-1044 / T2C with LCD ST2751A01-8, diagonal size 27.5 "(70 cm) 16: 9. The required brightness of the screen of 200 cd / m2 is provided by LED backlighting. The ratio of maximum brightness to minimum ( contrast) is 3000: 1. The display technology of the model is implemented with LED backlighting.
ST2751A01-8 sensor and CV512H-U42 motherboard software provide high quality HD viewing at 1366x768 pixels in 720p (HD Ready). Supported media file formats: MP3, MPEG4, HEVC (H.265), MKV, JPEG.
The power of the acoustic system of sound is 10 W (2x5 W), provided by two speakers. The NICAM STEREO audio processing system is used.
External interface (communication with other devices) is supported by standard input and output connectors: antenna input (RF), AV, component, VGA, HDMI x3, USB. A headphone output is provided. The digital tuner is capable of receiving television channels in the DVB-T MPEG4, DVB-C, DVB-T2 standards.
The TV can use a power supply unit as part of the MainBoard.
Dimensions: with stand 643x418x137 mm, without stand 643x393x86 mm.
TV weight: 3.1 kg.
Attention! The ST2751A01-8 panel of the BBK 28LEM-1044 / T2C LED TV is an expensive and unreliable element.
Do not allow any impact on the glass and pressure on the screen surface to avoid damage to the LED panel!
It is also unsafe for liquid to spill onto the screen. Sometimes one drop is enough if it drips down the glass onto the cables to make the TV unrepairable.