REPAIRING AND NOT THROWING AWAY

Richtige Fernseher haben Röhren!

Richtige Fernseher haben Röhren!

In Brief: On this site you will find pictures and technical information about Service Modes, Circuit Diagrams, Firmware Update procedure, Disassemble procedure, Universal remote control set-up codes, Troubleshooting and more....

If you go into the profession, you will obtain or have access to a variety of tech tips databases HERE IT IS Master Electronics Repair !.

These are an excellent investment where the saying: 'time-is-money' rules. However, to learn, you need to develop a general troubleshooting approach - a logical, methodical, method of narrowing down the problem. A tech tip database might suggest: 'Replace C536' for a particular symptom. This is good advice for a specific problem on one model. However, what you really want to understand is why C536 was the cause and how to pinpoint the culprit in general even if you don't have a service manual or schematic and your tech tip database doesn't have an entry for your sick TV or VCR.

While schematics are nice, you won't always have them or be able to justify the purchase for a one-of repair. Therefore, in many cases, some reverse engineering will be necessary. The time will be well spent since even if you don't see another instance of the same model in your entire lifetime, you will have learned something in the process that can be applied to other equipment problems.
As always, when you get stuck, checking out a tech-tips database may quickly identify your problem and solution.In that case, you can greatly simplify your troubleshooting or at least confirm a diagnosis before ordering parts.

Happy repairing!
Today, the West is headed for the abyss. For the ultimate fate of our disposable society is for that society itself to be disposed of. And this will happen sooner, rather than later.

How to use the site:

- If you landed here via any Search Engine, you will get what you searched for and you can search more using the search this blog feature provided by Google. You can visit more posts scrolling the left blog archive of all posts of the month/year,
or you can click on the main photo-page to start from the main page. Doing so it starts from the most recent post to the older post simple clicking on the Older Post button on the bottom of each page after reading , post after post.

You can even visit all posts, time to time, when reaching the bottom end of each page and click on the Older Post button.

- If you arrived here at the main page via bookmark you can visit all the site scrolling the left blog archive of all posts of the month/year pointing were you want , or more simple You can even visit all blog posts, from newer to older, clicking at the end of each bottom page on the Older Post button.
So you can see all the blog/site content surfing all pages in it.

- The search this blog feature provided by Google is a real search engine. If you're pointing particular things it will search IT for you; or you can place a brand name in the search query at your choice and visit all results page by page. It's useful since the content of the site is very large.

Note that if you don't find what you searched for, try it after a period of time; the site is a never ending job !

..............The bitterness of poor quality is remembered long after the sweetness of todays funny gadgets low price has faded from memory........ . . . . . .....
Don't forget the past, the end of the world is upon us! Pretty soon it will all turn to dust!

©2010, 2011, 2012, 2013, 2014 Frank Sharp - You do not have permission to copy photos and words from this blog, and any content may be never used it for auctions or commercial purposes, however feel free to post anything you see here with a courtesy link back, btw a link to the original post here , is mandatory.
All posts are presented here for informative, historical and educative purposes as applicable within fair use. NOTHING HERE IS FOR SALE !

Thursday, 17 September 2020

FUNAI LCD A3206 - 32 INCH LCD TV HOW TO ENTER THE SERVICE MODE HOW TO INITIALIZE, ELECTRICAL ADJUSTMENTS PSU SMPS AND BACKLIGHT INVERTER SCHEMATIC, WHITE BALANCE ADJUSTMENT, FLICKER ADJUSTMENT

FUNAI 32" COLOR LCD TELEVISION - LCD-A3206 - LCD-B3206 -  LCD-C3206 - LCD-D3206

  Always respect voltages. While some may not be dangerous in themselves, they can cause unexpected reactions that are best avoided. Before reaching into a powered TV set, it is best to test the high voltage insulation. It is easy to do, and is a good service precaution.

Hot Chassis Warning
a.
Some TV receiver chassis are electrically connected directly to one conductor of the AC power cord and maybe safety-serviced without an isolation transformer only if the AC power plug is inserted so that the chassis is connected to the ground side of the AC power source. To confirm that the AC power plug is inserted correctly, with an AC voltmeter, measure between the chassis and a known earth ground. If a voltage reading in excess of 1.0V is obtained, remove and reinsert the AC power plug in the opposite polarity and again measure the voltage potential between the chassis and a known ground.
b. Some TV receiver chassis normally have 85V AC(RMS) between chassis and earth ground regardless of the AC plug polarity. This chassis can be safety-serviced only with an isolation transformer inserted in the power line between the receiver and the AC power source, for both personnel and test equipment protection.
c. Some TV receiver chassis have a secondary ground system in addition to the main chassis ground. This secondary ground system is not isolated from the AC power line. The two ground systems are electrically separated by insulation material that must not be defeated or altered.

Disassembly Flowchart
This flowchart indicates the disassembly steps for the cabinet parts, and the CBA in order to gain access to item(s) to be serviced. When reassembling, follow the steps in reverse order. Bend, route and dress the cables as they were.



Disassembly Method





HOW TO INITIALIZE THE LCD TELEVISION
To put the program back at the factory-default, initialize the LCD television as the following procedure.
How to initialize.
1. Turn the power off.
2. To enter the service mode,
while pressing [SETUP] button, press [STANDBY-ON] button on the TV unit.
- To cancel the service mode, press [STANDBYON] button on the remote control.
3. To initialize the LCD television, press “DISPLAY” button on the remote control unit.
4. Confirm "FF" indication on the upper left of the screen.

ELECTRICAL ADJUSTMENTs

Electrical adjustments are required after replacing circuit components and certain mechanical parts. It is important to perform these adjustments only after all repairs and replacements have been completed.
Also, do not attempt these adjustments unless the proper equipment is available.
Test Equipment Required
1. DC Voltmeter
2. Pattern Generator
3. Colour Analyzer
How to Set up the Service mode.
1. Turn the power off.
2. While pressing [SETUP] button, press [STANDBYON] button on the TV unit.
- To cancel the service mode, press [STANDBY-ON] button on the TV unit.

Initial Setting
General
Enter the Service mode.
Set the each initial data as shown on table.


Flicker Adjustment
This adjustment is needed when reparing T-CON CBA.
1. Enter the Service mode.
2. Press [2] button on the remote control unit. The following screen appears.

3. If Flicker Adjustment is not fit, the screen become the following.

4. Turn the VR1 on the LCD Module so that flash stops.

Purity Check Mode
This mode cycles through full-screen displays of red, green, blue, and white to check for non-active pixels.
1. Enter the Service mode.
2. Each time pressing [7] button on the service remote control unit, the display changes as follows.

Auto Calibration.
Purpose: To bring the colour adjustment of each component into standard alignment.
Symptom of Maladjustment:

 If this adjustment is incorrect, component signals do not reproduce the corresponding color.

Gain Adjustment
1. Input white raster signal (5%=5 IRE, 100%=100 IRE) from Component jack.

2. Enter the service mode.
3. To enter the Auto Calibration. adjustment mode, press [5] button on the service remote control unit.
4. To start auto adjustment, press [CH UP] button on the service remote control unit.
- In the auto adjustment mode, “Please Wait” appears on the screen.
- Upon completion, “OK” and appears on the screen.
- If the auto adjustment failure, “ NG” appears on the screen.

Offset Adjustment.
5. Input white raster signal (5%=5 IRE) from Component jack.

6. Enter the service mode.

7. To enter the Auto Calibration adjustment mode, press [6] button on the service remote control unit.
8. To start auto adjustment, press [CH UP] button on the service remote control unit.
- In the auto adjustment mode, “Please Wait” appears on the screen.
- Upon completion, “OK” and appears on the screen.
- If the auto adjustment failure, “ NG” appears on the screen.

The following adjustment normally is not attempted in the field. Only when replacing the LCD Panel then adjust as a preparation.

White Balance Adjustment
*This adjustment is needed when repairing T-CON CBA.
Purpose: To mix red, green and blue beams correctly for pure white.
Symptom of Maladjustment: White becomes bluish or reddish.

1. Operate the unit for more than 20 minutes.
2. Input the White Purity.

3. Set the color analyzer to the CHROMA mode and bring the optical receptor to the center on the LCD-Panel surface after zero point calibration as shown.
Note: The optical receptor must be set perpendicularly to the LCD Panel surface.
4. [CVBS]
Enter the Service mode. Press “VOL DN” button on the remote control unit and select “C/D/S 1” mode.

[YUV]
Enter the Service mode. Press “VOL DN” button on the remote control unit and select “C/D/S 2” mode.
[RGB]
Enter the Service mode. Press “VOL DN” button on the remote control unit and select “C/D/S 3” mode.

5. [CVBS]----(APL 70%)
Press “6” button to select “DB 1(C/D/S 1)” for Blue adjustment. Press “4” button to select “DR 1(C/D/S 1)” for Red adjustment. When “x” value and “y” value are not within specification, adjust “DB 1(C/ D/S 1)” or “DR 1(C/D/S 1)”. Refer to “1. Initial Setting.”
[CVBS]----(APL 25%)
Press “3” button to select “COB 1(C/D/S 1)” for Blue adjustment. Press “1” button to select “COR 1(C/D/S 1)” for Red adjustment. When “x” value and “y” value are not within specification, adjust “COB 1(C/D/S 1)” or “COR 1(C/D/S 1)”. Refer to “1. Initial Setting.”
After adjusting (APL 25%), verify (APL 70%) again and adjust repeatedly until both values are within specification.
6. [YUV]----(APL 70%)
Press “6” button to select “DB 2(C/D/S 2)” for Blue adjustment. Press “4” button to select “DR 2(C/D/S 2)” for Red adjustment. When “x” value and “y” value are not within specification, adjust “DB 2(C/ D/S 2)” or “DR 2(C/D/S 2)”. Refer to “1. Initial Setting.”
[YUV]----(APL 25%)
Press “3” button to select “COB 2(C/D/S 2)” for Blue adjustment. Press “1” button to select “COR 2(C/D/S 2)” for Red adjustment. When “x” value and “y” value are not within specification, adjust “COB 2(C/D/S 2)” or “COR 2(C/D/S 2)”.  Refer to “1. Initial Setting.”
After adjusting (APL 25%), verify (APL 70%) again and adjust repeatedly until both values are within specification.
7. [RGB]----(APL 70%)
Press “6” button to select “DB 3(C/D/S 3)” for Blue adjustment. Press “4” button to select “DR 3(C/D/S 3)” for Red adjustment. When “x” value and “y” value are not within specification, adjust “DB 3(C/ D/S 3)” or “DR 3(C/D/S 3)”. Refer to “1. Initial Setting.”
[RGB]----(APL 25%)
Press “3” button to select “COB 3(C/D/S 3)” for Blue adjustment. Press “1” button to select “COR 3(C/D/S 3)” for Red adjustment. When “x” value and “y” value are not within specification, adjust “COB 3(C/D/S 3)” or “COR 3(C/D/S 3)”. Refer to “1. Initial Setting.”
After adjusting (APL 25%), verify (APL 70%) again and adjust repeatedly until both values are within specification.
8. Turn the power off and on again. (Main power button on the TV unit.)

Power [SMPS] and backlight board schematic.