Technical description and composition of the THOMSON T32ED13DU TV, panel type and modules used. The composition of the modules.THOMSON LED
Model: T32ED13DU
Chassis / Version: 40-MT31BP-MAA2LG
Panel: LVW320CSDXE4V11
LED backlight: 4C-LB320T-YH5
T-CON: MT315A04-1-XC-9
LED driver (backlight): integrated into MainBoard
PWM LED driver: MP3398A
MOSFET LED driver: ME25N06
Power Supply (PSU): integrated into MainBoard
PWM Power: LD7536 (PWM SOT23-6)
MOSFET Power: 4N65
MainBoard: 40-MT31BP-MAA2LG
IC MainBoard: CPU: MT5531NDNT 1429-BCAH, SPI Flash: 25Q64F, SOUND: RT9108NB
Tuner: ST34WN-2T-E
Specifications T32ED13DU
THOMSON T32ED13DU
General recommendations for TV LCD LED repair
Possible malfunctions
- THOMSON T32ED13DU TV does not turn on at all. No response to the remote control and front panel control buttons. Indicator lamps do not light up or flash.
In such cases, the 40-MT31BP-MAA2LG power supply usually fails. Then we recommend measuring its output voltages and, if they are absent, you should check the serviceability of the power switches (4N65) and the rectifier diodes of the converters for a possible short circuit.
In case of breakdowns of semiconductors in the secondary circuits of any converter, as a rule, it can operate in an emergency mode of short circuit without output voltages, and with a short circuit in the elements of the primary circuit, the mains fuse most often breaks off immediately and less often the current sensor in the source of the key.
The breakdown of power switches (MosFet) in switching sources is sometimes caused by malfunctions of other circuit elements, for example, in the circuits supplying the PWM controller, frequency setting or damper, as well as in the circuits of Negative Feedback (OOS) stabilization. PWM regulators (PWM) LD7536 (PWM SOT23-6), if they have no visible damage to the case and an open short circuit between the pins, are usually checked by replacing.
- There is no image, there is sound, it reacts to the remote control. Or, immediately after switching on for a second, the image may appear and immediately disappear.
In some of these cases, the malfunction is caused by the lack of display backlighting. The reason may be both in the power supply of the LEDs, in their serviceability (breakdown or breakage), as well as in the violation of the contact connections of the LED strips.
To check the health of the LED circuit, it is better to use a current source with a maximum voltage of 200V. We do not recommend using any voltage sources for this purpose. You can check each LED separately with a simple Chinese multimeter (powered by 9 volts) in the P-N transition test mode. If you connect the red probe of the multimeter to the anode of the LED, and the black one to its cathode, then the 3-volt LED will light up slightly, and in the opposite direction you can detect the transition of the emergency zener diode. The serviceability of the PN junction of the Zener diode indirectly indicates the serviceability of the LED-a
- The TV does not turn on, does not respond to the remote control. The indicator blinks or signals the standby mode.
Repair or diagnostics of the 40-MT31BP-MAA2LG motherboard should begin with checking the stabilizers and power converters required to power the microcircuits and matrix. If necessary, you should update or replace the software (software). In cases of complex MB (SSB) repairs and with the necessary skills and equipment, it may sometimes be necessary to replace its CPU chips: MT5531NDNT 1429-BCAH, SPI Flash: 25Q64F, SOUND: MP3398A and other possible faulty components. Malfunctions associated with the use of BGA soldering technologies are usually easily diagnosed by the warm-up method.
If THOMSON T32ED13DU does not have an image, but there is sound, often the display backlight simply does not work. Moreover, in LED TVs, the LEDs inside the panel usually fail, less often the LED driver.
In such cases, you can see a barely noticeable image with a successful hit of external light on the screen.
Replacing the LEDs requires disassembling the LCD panel - a process that requires experience and qualifications from the master. We do not recommend doing such work on your own to the owners of TVs and craftsmen who do not have experience in repairing LCD panels
If there is no image, and the backlight is on, the screen becomes slightly lighter when turned on, and in an open TV you can see light through the holes in the panel case.
In this case, the panel may also be faulty - damage to the strips, loops, for example, as a result of moisture ingress after unsuccessful washing of the screen, the T-CON (Timing Controller) board may be faulty. But often the main board MainBoard turns out to be faulty, a software failure is also possible.
Then, first of all, it is necessary to check the panel supply voltage, fuses on the T-CON board, as well as the supply and reference voltages of the column and line drivers - VGH, VGL, Vcom.
If these measurements are within normal limits, it is necessary to trace the passage of LVDS signals from the MainBoard with an oscilloscope, as well as synchronization signals to the loops with drivers.
Flooded or unsuccessfully washed screens of LED TVs can be restored, in about half of the cases, usually if significant damage has not formed in the loops and panel strips.
If the TV operates normally from external devices, but does not tune to TV channels, the ST34WN-2T-E tuner may be faulty. In such cases, first of all, you should make sure that there are supply voltages at its corresponding terminals. It is also necessary to make sure that the tuner and processor can exchange data via the I2C bus. Sometimes the reason for the inoperability of the tuner may be a software failure.
Attention to TV owners! Attempts to repair THOMSON T32ED13DU on your own are not recommended by the manufacturer and can lead to serious negative consequences!
DOWNLOAD SCHEMATIC DIAGRAM / SERVICE MANUAL ------------------> THOMSON T32ED13DU Chassis 40-MT31BP-MAA2LG
The appearance of the MainBoard 40-MT31BP-MAA2LG is shown in the figure below:40-MT31BP-MAA2LG
40-MT31BP-MAA2LG can be used in TVs:
ERISSON 32LET82 (Panel LVW320CSOT E145 V2), ERISSON 32LET42T2 (Panel LVW320CSOT E274 V2), ERISSON 32LET41T2 (Panel LVW320CS0T E274 V2), FUSION FLTV-32T21 (Panel LVW320CZOT), SUPRA STV-LC32T420WL (Panel LVW320CSOT E155 V2), SUPRA STV-LC32T850WL (Panel LVW320CSOT E45 V1), SUPRA STV-LC28T662WL (Panel T8-28T3520-LPM20), SUPRA STV-LC24T850WL (Panel 720p HD 1366x768), TELEFUNKEN TF-LED32S29T2 (Panel LVW320CS0T E198 V4), TELEFUNKEN TF-LED24S29T2 (Panel V236BJ1-LE2 Rev.C1), THOMSON T24E12DHU-01B T24E12DHU (Panel LVW240AUDX E2 V6).
The main features of the THOMSON T32ED13DU device:
Installed matrix (LED panel) LVW320CSDXE4V11.
Matrix control uses MT315A04-1-XC-9 Timing Controller (T-CON).
To power the backlight LEDs, a converter combined with the 40-MT31BP-MAA2LG main board is used, controlled by the MP3398A PWM controller. The keys of the ME25N06 type are used as power elements of the LED driver.
The power module is combined with the MainBoard and is made according to the AC / DC flyback voltage converter using LD7536 microcircuits (PWM SOT23-6) and power switches of the 4N65 type.
MainBoard - the main board (motherboard) is a 40-MT31BP-MAA2LG module, using CPU chips: MT5531NDNT 1429-BCAH, SPI Flash: 25Q64F, SOUND: RT9108NB and others.
The ST34WN-2T-E tuner provides reception of television programs and tuning to channels.
LED TV THOMSON T32ED13DU with LCD, diagonal size 32 "(81 cm) 16: 9 format. The declared brightness of the screen of 250 cd / m2 is provided by modern LED backlight LED. The ratio of maximum brightness to minimum (contrast) is not less than 4000: 1. The LCD panel uses direct backlighting with rear LEDs - Direct LED. You can view in high quality HD at a resolution of 1366x768 pixels in 720p standard (HD Ready). Input high-frequency or video signal is decoded in analog systems PAL, SECAM, NTSC. digital signal (graphic format) is produced in the standards 480i, 576i, 576p, 720p, 1080i, 1080p Multimedia formats are supported: MP3, JPEG.
Speaker power of 10 W (2x5 W) is provided by two speakers. The NICAM STEREO audio processing system is used.
External interface (communication with other devices) is supported by standard input and output connectors: antenna input (RF), AV, component, VGA, HDMI x2, MHL, USB. A standard VGA (D-Sub 15) connector is used to connect a laptop or computer. This interface supports resolutions: 1360x768. The digital tuner has the ability to receive television channels in the DVB-T MPEG4, DVB-C, DVB-T2 standards.
The power consumed by the TV from the network in the operating mode is not more than 50 W.
Dimensions: with stand 734x505x205 mm, without stand 734x441x91 mm.
TV weight: 5.4 kg.
Attention! The panel of the THOMSON T32ED13DU LED TV is an expensive and unreliable element.
Do not allow any impact on the glass and pressure on the screen surface to avoid damage to the LED panel!
It is also unsafe for liquid to spill onto the screen. Sometimes one drop is enough if it drips down the glass onto the cables to make the TV unrepairable.
