Technical description and composition of the LG 49UJ630V TV, panel type and modules used. The composition of the modules.LG LED
Model: 49UJ630V
Chassis / Version: LJ7 Chassis
Panel: SDL490W0 (LD0-B11)
LED backlight: JL.D49091330-001FS-M
LED driver (backlight): integrated into PSU
PWM LED driver: SMD
MOSFET LED driver: TO-252
Power Supply (PSU): LGP49DJ-17U1 EAY64511101 (1.6)
PWM Power: PFC, PWM
MOSFET Power: TO-252
MainBoard: EAX67133404 (1.0)
IC MainBoard: Realtek K3Lp, FT24C256A, DTA2010M
Tuner: TDJN-G501D EBL61841001
Specifications 49UJ630V
LG 49UJ630V
General recommendations for TV LCD LED repair
Possible malfunctions
- LG 49UJ630V does not turn on, indicators on the front panel do not light or flash. The TV does not respond to the control buttons and the remote control.
In such cases, the LGP49DJ-17U1 power supply is usually defective. It is necessary to measure its secondary output voltages, and if they are absent, check the power switches (TO-252) and rectifier diodes in the converters for a short circuit.
In case of breakdowns of semiconductors in the secondary circuits of any converter, as a rule, it can operate in an emergency mode of short circuit without output voltages, and with a short circuit in the elements of the primary circuit, the mains fuse most often breaks off immediately and, less often, the current sensor in the source of the key.
Breakdown of power switches (MosFet) in switching sources is sometimes caused by malfunctions of other circuit elements, for example, in the circuits supplying the PWM controller, frequency setting or damper, as well as in the circuits of Negative Feedback (OOS) stabilization. PWM controllers (PWM) PFC, PWM, if they do not have visible damage to the case and an outright short circuit between the pins, are usually checked by replacement.
- There is no picture, but there is sound and reaction to the remote control. Or, for a second, the image may appear immediately after switching on.
Usually, in such cases, there is no backlighting of the LED panel (matrix). Usually the cause of the malfunction is in the breakage of the LEDs, or in the connectors of the LED strips, but sometimes the LED driver is also faulty.
It is impossible to check the line of series-connected LEDs without a special current source, and it is unsafe for them to use any voltage sources above 12V for this purpose. Then all that remains is to open the panel and check each LED separately. Usually, Chinese multimeters with 9V power supply lightly light one 3-volt LED, if you connect the probes to it in the forward direction, the red probe to the anode, the black one to the cathode. For dual 6-volt LEDs, the PN junction of its emergency zener diode can serve as an indicator of the LED health. In the event of a malfunction of the LED, its zener diode will either be cut off or pierced in the K / Z.
- The TV does not go into operation, does not respond to the remote control. The indicator on the front panel is on or blinking.
Repair or diagnostics of the EAX67133404 motherboard should begin with checking the stabilizers and power converters required to power the microcircuits and matrix. If necessary, you should update or replace the software (software). Complex repair of MB (SSB) is possible only in a service center with the necessary equipment. Checking or replacing Realtek K3Lp, FT24C256A, DTA2010M elements requires the necessary training and professional skills in repairing modules at the component level. Problems associated with the use of BGA soldering technologies can sometimes be diagnosed by the warm-up method.
If LG 49UJ630V has no picture, but there is sound, often the display backlight SDL490W0 (LD0-B11) simply does not work. Moreover, in LED TVs, the LEDs inside the panel usually fail, less often the LED driver.
In such cases, you can see a barely noticeable image with a successful hit of external light on the screen.
Replacing the LEDs requires disassembling the SDL490W0 LCD panel - a process that requires experience and qualifications from the master. We do not recommend doing such work on your own to the owners of TVs and craftsmen who do not have experience in repairing LCD panels
If there is no image, and the backlight is on, the screen becomes slightly lighter when turned on, and in an open TV you can see light through the holes in the panel case.
In this case, the panel may also be faulty - damage to strips, loops, for example, as a result of moisture ingress after unsuccessful washing of the screen, the T-CON (Timing Controller) board may be faulty. But the main board MainBoard EAX67133404 often turns out to be faulty, a software failure is also possible.
Then, first of all, you need to check the panel supply voltage, the fuses on the T-CON board, as well as the supply and reference voltages of the column and line drivers - VGH, VGL, Vcom.
If these measurements are within the normal range, it is necessary to trace the passage of LVDS signals from the MainBoard EAX67133404 with an oscilloscope, as well as synchronization signals to the loops with drivers.
Flooded or unsuccessfully washed screens of LED TVs can be restored, in about half of the cases, usually if significant damage has not formed in the loops and panel strips.
If the TV operates normally from external devices, but does not tune to TV channels, the TDJN-G501D EBL61841001 tuner may be faulty. In such cases, first of all, you should make sure that there are supply voltages at its corresponding terminals. It is also necessary to make sure that the tuner and processor can exchange data via the I2C bus. Sometimes the reason for the inoperability of the tuner may be a software failure.
Owners of the 49UJ630V TV are advised to contact only qualified specialists with the necessary work experience for repair! Attempts to repair yourself without the appropriate knowledge and skills can lead to irreversible negative consequences!
DOWNLOAD SCHEMATIC DIAGRAM / SERVICE MANUAL ------------------> CHASSIS : UD74P for models 49UJ630*, 49UJ630*-ZA, 49UJ639V, 49UJ639V-ZE, 49UJ6307, 49UJ630V
Additional MainBoard RepairThe appearance of the MainBoard EAX67133404 is shown in the figure below:
EAX67133404
External view of the power supply
Main features of the LG 49UJ630V device:
Installed matrix (LED panel) SDL490W0 (LD0-B11).
A converter combined with a power supply is used to power the backlight LEDs and is controlled by an SMD PWM controller. TO-252 switches are used as power elements of the LED driver.
The formation of the necessary supply voltages for all nodes of the LG 49UJ630V TV is carried out by the LGP49DJ-17U1 power module, or its analogs using PFC, PWM microcircuits and power switches of the TO-252 type.
MainBoard - the main board (motherboard) is an EAX67133404 module, using Realtek K3Lp, FT24C256A, DTA2010M and others.
Tuner TDJN-G501D EBL61841001 provides reception of television programs and tuning to channels.
There are files to download for model 49UJ630V from the manufacturer:Files with updates and instructions:
File Description File Name Type Date Size
SW File (Version 05.80.50). Update instructions TV_Software_Update_Guide_v3.pdf PDF 01/22/2020 2014K
SW File (Version 05.80.50). Firmware (USB) Software_File (Version_05.80.50) .zip ZIP 01/22/2020 831673K
Compatible with 43UJ620V-ZA, 43UJ6307-ZA, 43UJ6309-ZA, 43UJ630V-ZA, 43UJ631V-ZA, 43UJ634V-ZD, 43UJ635V-ZF, 43UJ639V-ZE, 43UJ6517-ZA, 43UJ6519-ZA, 43UJ651V-ZA, 43UJ655V-ZC, 43UJ670V-ZD, 43UJ675V-ZC, 43UJ701V-ZC, 49UJ620V-ZA, 49UJ6307-ZA, 49UJ6309-ZA, 49UJ630V-ZA, 49UJ631V-ZA, 49UJ634V-ZD, 49UJ635V-ZF, 49UJ639V-ZE, 49UJ6517-ZA, 49UJ6519-ZA, 49UJ651V-ZA, 49UJ655V-ZC, 49UJ670V-ZD, 49UJ675V-ZC, 49UJ701V-ZC, 55UJ620V-ZA, 55UJ6307-ZA, 55UJ6309-ZA, 55UJ630V-ZA, 55UJ634V-ZD, 55UJ635V-ZF, 55UJ6517-ZA, 55UJ6519-ZA, 55UJ651V-ZA, 55UJ655V-ZC, 55UJ670V-ZD, 55UJ675V-ZC, 55UJ701V-ZC, 55UK6100PLA, 55UK6100PLB, 60UJ6307-ZA, 60UJ6309-ZA, 60UJ630V-ZA, 60UJ634V-ZD, 60UJ6517-ZA, 60UJ6519-ZA, 60UJ651V-ZA, 65UJ620V-ZA, 65UJ6307-ZA, 65UJ6309-ZA, 65UJ630V-ZA, 65UJ634V-ZD, 65UJ6517-ZA, 65UJ6519-ZA, 65UJ651V-ZA, 65UJ655V-ZC, 65UJ670V-ZD, 65UJ675V-ZC, 65UJ701V-ZC, 65UK6100PLA, 65UK6100PLB, 70UJ675V-ZA, 75UJ651V-ZB, 75UJ675V-ZA.
User Manuals and Instructions:
File type File name Language Date Size
User Manual UJ630_ (ENG) .pdf English 20.11.2017 18094K
Quick Start Guide w3.5_mr_e05_c.zip English, Estonian, Latvian, Lettish, Lithuanian, Russian 10/31/2019 56,267K
Instructions for quick setup Web_OS_3.5_Smart_QSG_ENG.pdf English 09/25/2017 4926K
The files can be downloaded from the manufacturer's website for the 49UJ630V model.
TV LG 49UJ630V with LCD SDL490W0 (LD0-B11), diagonal size 48.5 "(123 cm) 16: 9 format. The LCD-panel implements the principle of direct backlight display with rear-mounted LEDs - Direct LED.
SDL490W0 sensor and MainBoard EAX67133404 software are capable of realizing images in the highest UHD quality at a resolution of 3840x2160 pixels in 4K UHD, HDR standard. Image processing is performed using modern High Dynamic Range (HDR) technology with an extended range of brightness gradations.
The 49UJ630V TV has built-in SMART software and webOS operating system installed. The connection to the network can be carried out via Wi-Fi wireless connection. Supported media file formats: MP3, WMA, MPEG4, HEVC (H.265), DivX, MKV, JPEG.
Speaker sound system power 20 W (2x10 W) is provided by two speakers. The NICAM stereo audio processing system and the Sound Surround function are used.
Communication with other devices via an external interface is supported by standard input and output connectors: antenna input (RF), AV, component, HDMI x3, USB x2, Ethernet (RJ-45), Bluetooth, Wi-Fi 802.11ac, WiDi, Miracast. A headphone jack is provided.
The digital tuner can receive TV channels in the DVB-T MPEG4, DVB-C, DVB-T2, DVB-S2 standards.
The TV uses the LGP49DJ-17U1 power supply.
Dimensions: With stand 1110x705x235 mm, Without stand 1110x650x81 mm.
Attention! The SDL490W0 panel of the LG 49UJ630V LED TV is an expensive and unreliable element.
Do not allow any impact on the glass and pressure on the screen surface to avoid damage to the LED panel!
It is also unsafe for liquid to spill onto the screen. Sometimes one drop is enough if it drips down the glass onto the cables to make the TV unrepairable.
