
SAMSUNG LED
Model: UE40H5303 UE40H5303AK
Panel: CY-DF400BGLV1V
LED backlight: D3GE-400SMA-R2 [13.07.10] D3GE-400SMB-R2 [13.07.10]
T-CON: 13Y FHD_60Hz_V02 BN41-01938B
LED driver (backlight): integrated into PSU; 152V 425mA
Power Supply (PSU): BN44-00770A L40HFP_ESM PSFL940H06A
MainBoard: BN41-02241A BN94-07772A
IC MainBoard: SPI Flash: 25Q40CL; EEPROM: ATMLH 416 2EC; SOUND: TAS5747PHPR
Tuner: DNTQ403IL286A BN40-00287A
Control: BN59-01178B, WIFI: WIDT30Q BN59-01174A
Technical Specifications UE40H5303
SAMSUNG UE40H5303
General repair guidelines for TV LCD LED
If the TV does not turn on, no control lights are on or blinking, there are no sounds when you turn on and there is not the slightest sign of operability - the most likely malfunction is in the power module. When repairing the power supply, it is advisable to start the diagnosis by checking the mains fuse and the electrolytic capacitors of the filters of the converter secondary rectifiers. In the event of a fuse breaking, the reason should be sought in the power semiconductor elements of the pulse converter of the main power supply. First of all, it is necessary to check the diodes of the bridge of the rectifier of the mains voltage and the power key (s) of the converter. The complete inoperability of the power supply unit can be caused by a short circuit in the power elements in the primary circuit, followed by an open fuse, or a short circuit in the loads.
The LED driver for the display backlight is made according to the boost converter circuit on the common board of the power module BN44-00770A.
If there is no image when you turn on the SAMSUNG UE40H5303, or it appears and immediately disappears, but there is sound, most likely there is a malfunction in the backlight LED circuit of the CY-DF400BGLV1V panel, or in the node of the LED driver.
To check the health of the LEDs and contact connections in their power circuit, the panel must be disassembled.
To detect a break in the LED lines without disassembling the panel, a current source is required. It is impossible to open transitions connected in series with a simple multimeter; voltage of several tens of volts is necessary.
Repair of the motherboard BN41-02241A BN94-07772A must begin with the diagnosis and verification of all linear stabilizers and power converters of its microcircuits. Sometimes it may be necessary to update the software (software) - flashing FLASH, EEPROM, NAND.
Often, the MB (SSB) card must be replaced in case of complex malfunctions that are difficult to detect. When trying to repair, you should check its elements - SPI Flash: 25Q40CL; EEPROM: ATMLH 416 2EC; SOUND: TAS5747PHPR and replace failed chips with new ones. Some malfunctions may be due to the use of BGA soldering technologies in modern Main Board. Typically, such defects are detected by local heating of the chip.
In the absence of tuning to local television channels, you should make sure that the software is correct, as well as the presence of supply voltages at the terminals of the tuner DNTQ403IL286A. The data exchange of the tuner with the processor can be controlled using an oscilloscope.
Attention to the owners! Attempts to repair the TV SAMSUNG UE40H5303 on its own are not recommended by the manufacturer and can lead to serious negative consequences!

BN41-02241A
BN41-02241A can be used in TVs:
SAMSUNG UE40H5303 UE40H5303AK (Panel CY-DF400BGLV1V), SAMSUNG UE40H6203 UE40H6203AK (Panel CY-DF400CSLV3V), SAMSUNG UE46H6233 UE46H6233AK (Panel CY-DF460CSLV1V), SAMSUNG UE46H5303AK (Panel CY-DF460BGLV1V), SAMSUNG UE55H6203AK UE55H6203 (Panel CY-DF550CSLV1V), SAMSUNG UE32H5303AK UE32H5303 (Panel CY-DF320BGLV1V LSF320HN02-A01), SAMSUNG UE46H6203AK UE46H6203 (Panel CY-DF460CSLV1V).
The appearance of the power supply
Main features of the SAMSUNG UE40H5303 device:
Installed matrix (LED-panel) CY-DF400BGLV1V.
The matrix control uses the Timing Controller (T-CON) 13Y.
To power the backlight LEDs, a converter is used, combined with a power supply.
The formation of the necessary supply voltages for all nodes of the SAMSUNG UE40H5303 TV is carried out by the power module BN44-00770A, or its analogues.
MainBoard - the main board (motherboard) is a BN41-02241A module, using SPI Flash chips: 25Q40CL; EEPROM: ATMLH 416 2EC; SOUND: TAS5747PHPR and others.
The tuner DNTQ403IL286A BN40-00287A provides the reception of television programs and tuning to channels.